Cisco Catalyst 3560-CX Bedienungs- und Sicherheitshinweise

Product Overview

The Catalyst 3560-CX and 2960-CX switches are Ethernet switches to which you can connect devices such

as Cisco IP Phones, Cisco Wireless Access Points, workstations, and other network devices such as servers,

routers, and other switches.

You can deploy these switches outside of the traditional wiring closet environment, such as in office

workspaces, hotel rooms, slot machines, kiosks, and classrooms. The switch is suitable for deployments

where there are space and power constraints (access to power outlets).

See the switch software configuration guide for deployment examples.

This chapter contains these topics:

•Switch Models, page 1

•Front Panel, page 2

•Rear Panel, page 9

•Management Options, page 13

•Network Configurations, page 14

Switch Models

Table 1: Catalyst 3560-CX and 2960-CX Switch Models and Descriptions

DescriptionSoftware

Image

Switch Model

8 10/100/1000 Power over Ethernet plus (PoE+) ports (PoE budget of

240 W); 2 Gigabit Ethernet and 2 small form-factor pluggable (SFP)1

module uplink slots.

IP BaseWS-3560CX-8PC-S

8 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 small form-factor

pluggable (SFP) module uplink slots.

IP BaseWS-3560CX-8TC-S

12 10/100/1000 PoE+ ports (PoE budget of 240 W); 2 Gigabit Ethernet

and 2 SFP module uplink slots.

IP BaseWS-3560CX-12PC-S

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

DescriptionSoftware

Image

Switch Model

12 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 SFP module

uplink slots.

IP BaseWS-3560CX-12TC-S

12 10/100/1000 PoE+ ports (PoE budget of 240 W); 2 Gigabit Ethernet

and 2 SFP+ 2module uplink slots.

IP BaseWS-3560CX-12PD-S

8 10/100/1000 PoE+ ports (PoE budget of 146W); 2 Gigabit Ethernet

uplink ports.

IP BaseWS-3560CX-8PT-S

2 Multigigabit 3100/1000/2500/5000/10000 PoE+ ports; 6 10/100/1000

PoE+ ports (PoE budget of 240 W); 2 SFP+ module uplink slots.

IP BaseWS-3560CX-8XPD-S

8 Gigabit Ethernet PoE+ ports; and 2 SFP module uplink slots.IP BaseWS-C3560CPX-8PT-S

6 Gigabit Ethernet ports; 2 multi-Gigabit Ethernet PoE+ ports; and 2

SFP+ uplink slots.

IP BaseWS-C3560CX-8PD-S

8 10/100/1000 PoE+ ports (PoE budget of 124 W); 2 Gigabit Ethernet

and 2 SFP module uplink slots.

LAN BaseWS-2960CX-8PC-L

8 10/100/1000 Ethernet ports; 2 Gigabit Ethernet and 2 SFP module

uplink slots.

LAN BaseWS-2960CX-8TC-L

1SFP = Gigabit uplink.

2SFP+ = 10-Gigabit uplink.

3Multigigabit ports support speeds of 100 Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps on Category 5e cable and up to 10 Gbps over Category 6a cabling

IP Base switches can be upgraded to IP Services with the RTU (right to use) software license.Note

Front Panel

•8 or 12 downlink Ethernet ports of one of these types:

◦10/100/1000

◦10/100/1000 PoE+

The Catalyst 3560CX-8XPD-S has 6 PoE+ ports and 2 Multigigabit PoE+ ports.Note

•Two 10/100/1000 uplink ports and two SFP or SFP+ module ports depending on the switch model.

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

Front Panel

•RJ-45 console port

•USB mini-Type B (console) port

•USB Type A port

•LEDs

Figure 1: Catalyst 3560CX Front Panel View

System LEDs5Mode button1

10/100/1000 PoE+ ports6USB Type A port2

10/100/1000 uplink ports7RJ-45 console port3

SFP module slots8USB mini-Type B (console) port4

Figure 2: Catalyst 3560CX-8XPD-S Front Panel View

System LEDs5Mode button1

10/100/1000 PoE+ ports6USB Type A port2

Multigigabit PoE+ ports7RJ-45 console port3

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

Front Panel

SFP module slots8USB mini-Type B (console) port4

PoE+ ports 1 to 6 are Gigabit Ethernet 1/0/1 to 1/0/6. The remaining ports are 10-Gigabit Ethernet 1/0/1

and 1/0/2. However, depending on the SFP type, the rightmost ports will either be 10-Gigabit Ethernet

1/0/3 and10-Gigabit Ethernet 1/0/4 or Gigabit Ethernet 1/0/7 and Gigabit Ethernet 1/0/8.

Note

PoE and PoE+ Ports

The ports provide PoE+ support for devices compliant with IEEE 802.3af, IEEE 802.3at, and ePoE and also

provide Cisco prestandard PoE support for Cisco IP Phones and Cisco Aironet Access Points.

The maximum switch power output is either 124 W or 240 W, depending on the switch mode. Intelligent

power management allows flexible power allocation across all ports.

For switches with a 124 W power budget, you can budget the PoE and PoE+:

•15.4 W of PoE output on 8 ports

•30 W of PoE+ output on 4 ports

For switches with a 240 W power budget, you can budget the PoE and PoE+:

•15.4 W of PoE output on 12 ports

•30 W of PoE+ output on 8 ports

On a per-port basis, you control whether or not a port automatically provides power when an IP phone or an

access point is connected.

The PoE ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters).

The 10BASE-T, 100BASE-TX, 1000BASE-T traffic requires Category 5, Category 5e, or Category 6 unshielded

twisted pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable.

Cisco intelligent power management capabilities include enhanced power negotiation, power reservation, and

per-port power policing. For information about configuring and monitoring PoE ports, see the switch software

configuration guide on Cisco.com.

The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC 60950-1.Note

10/100/1000 Ports

The 10/100/1000 ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet

(100 meters). The 10BASE-T, 100BASE-TX, 1000BASE-T traffic requires Category 5 or Category 5e twisted

pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable.

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

PoE and PoE+ Ports

Multigigabit ports

The Multigigabit ports can be configured to auto-negotiate multiple speeds on switch ports, and support 100

Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps speeds on Category5e cables, and up to 10 Gbps over Category6 and

Category 6A cables.

The Multigigabit ports support PoE and PoE+ for all the supported speeds and cable types. The following

table lists the cable types and speed.

10G5G2.5G1G100MbpsCable Type

N/AYesYesYesYesCategory5E

Yes (55meters)YesYesYesYesCategory6

YesYesYesYesYesCategory6A

Management Ports

The management ports connect the switch to a PC running Microsoft Windows or to a terminal server.

•RJ-45 console port (EIA/TIA-232). The RJ-45 console port connection uses an RJ-45-to-DB-9 female

cable.

•USB mini-Type B console port (5-pin connector).

If you use the USB mini-Type B console port, the Cisco Windows USB device driver must be installed on

any PC connected to the console port (for operation with Microsoft Windows). Mac OS X or Linux do not

require special drivers.

The 4-pin mini-Type B connector resembles the 5-pin mini-Type B connectors. They are not compatible. Use

only the 5-pin mini-Type B.

This illustration shows a 5-pin mini-Type B USB port.

Figure 3: USB Mini-Type B Port

With the Cisco Windows USB device driver, you can connect and disconnect the USB cable from the console

port without affecting Windows HyperTerminal operations.

The console output always goes to both the RJ-45 and the USB console connectors, but the console input is

active on only one of the console connectors at any one time. The USB console takes precedence over the

RJ-45 console. When a cable is connected into the USB console port, the RJ-45 console port becomes inactive.

Conversely, when the USB cable is disconnected from the USB console port, the RJ-45 port becomes active.

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

Multigigabit ports

You can use the command-line interface (CLI) to configure an inactivity timeout which reactivates the RJ-45

console if the USB console has been activated and no input activity has occurred on the USB console for a

specified time.

After the USB console deactivates due to inactivity, you cannot use the CLI to reactivate it. Disconnect and

reconnect the USB cable to reactivate the USB console. For information on using the CLI to configure the

USB console interface, see the software guide.

SFP and SFP+ Module Slots

The switch has either two 1-Gigabit SFP or 10-Gigabit SFP+ module slots. The slots marked SFP+ support

both SFP and SFP+ modules. The SFP slots support only the SFP modules.

For Cisco SFP and SFP+ modules documentation, including compatibility matrixes, refer to this URL: http:/

/www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

LEDs

You can use the switch system and port LEDs to monitor switch activity and performance.

This figure shows the switch LEDs and the Mode button that you use to select a port mode.

Figure 4: Switch LEDs and Mode Button

STACK LED 4

6Mode button1

Console LED7SYST LED (system)2

Port LEDs8STAT LED (status)3

Uplink port LED (copper)9SPEED LED4

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

SFP and SFP+ Module Slots

Uplink port LED ( SFP/SFP+)10PoE LED 5

4Only on switch models that have stacking capability. Note that this release does not support switch stacking.

5Only on switch models that support PoE.

System LED

System StatusColor

System is not powered on.Off

System is operating normally.Green

System is receiving power but is not operating

properly.

Amber

System StatusColor

System is not powered on.Off

System is operating normally.Green

System is receiving power but is not operating

properly.

Amber

POST is in progress.Blinking Green

Modes for Port LEDs

The port LEDs, as a group or individually, display information about the switch and about the individual

ports.

DescriptionPort ModeLED

The port status. This is the default mode.Port statusSTAT

The port operating speed: 10, 100, or 1000

Mb/s.

Port speedSPEED

The PoE status.PoE port powerPoE

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

LEDs

PoE LED

Even if the PoE mode is not selected, the LED shows PoE problems when they are detected. The PoE LED

is only on the switches that support PoE.

DescriptionColor

PoE is not enabled.Off

PoE is enabled. Ports are functioning correctly.Green

•PoE mode is not selected

•At least one of the 10/100 or 10/100/100 PoE ports has been denied

power

•At least one of the ports has a PoE fault

Blinking amber

Console LEDs

The console LEDs show which console port is in use.

If you connect a cable to a console port, the switch automatically uses that port for console communication.

If you connect two console cables, the USB-mini console port has priority.

DescriptionColorLED

RJ-45 console port is active.

USB-mini console port LED is not

active.

GreenRJ-45 console port

Port is not active.

USB-mini console port is active.

Off

USB-mini console port is active.

RJ-45 console port LED is not

active.

GreenUSB-mini console port

Port is not active.

RJ-45 console port is active.

Off

Port LEDs

RJ-45 ports and SFP-module slots have port LEDs. These LEDs, as a group or individually, provide information

about the switch and about the individual ports.

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

LEDs

DescriptionLED Color

No link or port was administratively shut down.Off

Link present but is not sending or receiving data.Green

Activity. Port is sending or receiving data.Blinking green

Link fault. Error frames can affect connectivity, and errors such as

excessive collisions, CRC errors, and alignment and jabber errors are

monitored for link faults.

Alternating green-amber

Port is blocked by Spanning Tree Protocol (STP) and is not forwarding

data. After a port is reconfigured, the port LED is amber for up to 30

seconds as STP searches for loops.

Amber

Rear Panel

•A security slot

•An AC power connector or a power adapter connector (on Catalyst 3560CX-8PT-S only)

•A loop (for the optional power cord retainer)

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

Rear Panel

•Heat sink fins (PoE models only)

Figure 5: Rear Panel of a Non-PoE Switch

Figure 6: Rear Panel of a PoE Switch

•A security slot

•An AC power connector

•A loop (for the optional power cord retainer)

Catalyst 3560-CX and 2960-CX Switch Hardware Installation Guide

Product Overview

Rear Panel

Andere Handbücher für Catalyst 3560-CX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 805 Series Bedienungsanleitung

Cisco

Cisco 1811W - Integrated Services Router Wireless Bedienungsanleitung

Cisco

Cisco 867VAE-W Bedienungsanleitung

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Bedienungsanleitung

Cisco

Cisco XR 12410 Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco Linksys WET11 Bedienungsanleitung

Cisco

Cisco MWR 2941 Betriebsanleitung

Cisco

Cisco ASR 920 series Bedienungsanleitung

Cisco

Cisco ASR 900 Series Bedienungsanleitung

Cisco

Cisco 3600 Series Handbuch

Cisco

Cisco 7204 - VXR Router Bedienungsanleitung

Cisco

Cisco XR 12416 Bedienungsanleitung

Cisco

Cisco cBR Series Handbuch

Cisco

Cisco C1109-2PX Kurzanleitung

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Bedienungsanleitung

Cisco

Cisco 2851 - Integrated Services Router Bedienungsanleitung

Cisco

Cisco 2811 - Voice Security Bundle Router Bedienungsanleitung

Cisco

Cisco ASR 1000 Series Bedienungsanleitung

Cisco

Cisco Linksys EA2700 Bedienungsanleitung

Cisco

Cisco ASR 901 10G Series Handbuch

Cisco

Cisco 1751 Bedienungsanleitung

Cisco

Cisco NCS55A1 Handbuch

Cisco

Cisco ONS 15454 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung