Cisco N540-FH-CSR-SYS Handbuch

Install the Device

Before you begin this task, ensure that you have read and understood the safety warnings in the Standard

Warning Statements section of the Safety Warnings handout.

•Install N540-FH-CSR-SYS, on page 1

•Install Cisco N540-FH-AGG-SYS, on page 23

Install N540-FH-CSR-SYS

Installing the Cisco N540-FH-CSR-SYS involves these tasks:

Rack Compatibility

We recommend that you follow these rack specifications.

Rack Types

Figure 1: Rack specification EIA (19 inches and 23 inches)

Install the Device

Table 1: Rack specification EIA (19 inches and 23 inches)

Mounting Flange

Dimension (Z)

Rack Mounting Hole

Centre-Centre (Y)

Rack Front Opening

(X)

Rack TypePost Type

482.6mm (19”)465mm (18.312”)450.8mm (17.75”)19 inches (48.3

centimeters)

4 Post

2 Post

584.2mm (23”)566.7mm (22.312”)552.45mm (21.75”)23 inches (58.4

centimeters)

4 Post

2 Post

Figure 2: Four Post Rack Type

Install the Device

Rack Types

Figure 3: Two Post Rack Type

Set up Device on Rack

You can set up the Cisco N540-FH-CSR-SYS on a rack.

Rack Mount

The device is shipped with rack mounting brackets that are to be secured on the sides of the device.

If the rack is on wheels, ensure that the brakes are engaged or the rack is otherwise stabilized.

Caution

Table 2: Cisco N540-FH-CSR-SYS Router Rack-Mount Kit

Part DescriptionQuantity

Front Rear brackets2

M4 x 0.7 x 7-mm Phillips flat-head screws16

12-24 x 0.49 inches L, Philips pan head screws4

Install the Device

Set up Device on Rack

1. Attach the rack-mount brackets and the cable guides to the router as follows:

a. The router has port-side intake modules, position the router so that its ports are facing the cold aisle.

b. Position the bracket ears facing front or middle rack-mount, on the side of the chassis so that the holes

are aligned.

c. Use four M4 screws to attach the brackets to the chassis.

d. Repeat Steps 1b and 1c with the other rack-mount bracket on the other side of the router.

Figure 4: Installing Rack-Mount Brackets

Install the Device

Rack Mount

Figure 5: Installing Cable Management and 19 inch Rack-Mount Brackets in the Front

Figure 6: Installing Cable Management and 19 inch Rack-Mount Brackets in the Middle

Install the Device

Rack Mount

Figure 7: Installing Cable Management and 19 inch Rack-Mount Brackets in the Rear

Figure 8: Installing Cable Management and 23 inch Rack-Mount Brackets in the Front

Install the Device

Rack Mount

Figure 9: Installing Cable Management and 23 inch Rack-Mount Brackets in the Middle

Figure 10: Installing Cable Management and ETSI Rack-Mount Brackets in the Front

Install the Device

Rack Mount

Figure 11: Installing Cable Management and ETSI Rack-Mount Brackets in the Middle

Figure 12: Installing Cable Management and ETSI Rack-Mount Brackets in the Rear

Ground the Device

Before you begin this task, ensure that you have read and understood the safety warnings in the Preventing

ESD Damage section of the Safety Warnings handout.

Install the Device

Ground the Device

Before you connect the power or turn on the power to the device, you must provide an adequate device ground

(earth) connection to your device.

This section describes how to ground the device. The grounding lug location is on the back panel of the device.

1. Verify that the ground cable is connected to the top of the rack and according to local site practice.

Figure 13: Ground Lug

2. Attach one end of the shelf ground cable (#6 AWG cable) to the ground point on the rear of the chassis

using the specified dual-hole lug connector.

• Use a wire-stripping tool to remove approximately 0.75 inches (19 mm) of the covering from the

end of the grounding cable.

• Insert the stripped end of the grounding cable into the open end of the grounding lug.

• Use the crimping tool to secure the grounding cable in the grounding lug.

• Remove the adhesive label from the grounding pad on the chassis.

• Place the grounding lug against the grounding pad so that there is solid metal-to-metal contact, and

insert the two M4 screws with washers through the holes in the grounding lug and into the grounding

pad.

• Ensure that the lug and cable do not interfere with other equipment.

• Prepare the other end of the grounding cable and connect it to an appropriate grounding point in your

site to ensure adequate earth ground.

Install the AC Power Cables

Refer Chapter 6: Replace Power Supply for more information about AC power cables installation.

Install the Device

Install the AC Power Cables

To install the AC power cables in the power supply slots:

1. Plug the power supply cord in the power supply module.

2. Insert the power supply cord into the tie [1, 3] and tighten the tie around the power supply cord as shown

in [2, 4] in the figure below.

Figure 14: Attach the AC Power Tie-and-Clip Cord

These images are for only representation purposes. Certain variants of Cisco NCS 540 do not include a tie

for the power supply cord.

Note

Activate an AC Power Supply Module

Perform the following procedure to activate an AC power supply:

Step 1 Plug the power cord into the power supply.

Step 2 Connect the other end of the power cord to an AC-input power source.

Step 3 Verify power supply operation by checking if the respective power supply front panel LED (PS0 or PS1) is green.

Step 4 If the LEDs indicate a power problem, see Troubleshooting for troubleshooting information.

Step 5 If you are also connecting a redundant AC power supply, repeat these steps for the second power source.

If you are connecting a redundant AC power supply, ensure that each power supply is connected to a separate

power source in order to prevent power loss in the event of a power failure.

Note

Install the Device

Activate an AC Power Supply Module

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco CRS Betriebsanleitung

Cisco

Cisco ME 4924-10GE Originalbetriebsanleitung

Cisco

Cisco XR 12000 Bedienungsanleitung

Cisco

Cisco 2621XM Bedienungsanleitung

Cisco

Cisco WS-C3550-12G Bedienungsanleitung

Cisco

Cisco 520-T1 - Small Business Pro SR Secure Router Bedienungsanleitung

Cisco

Cisco 7600 Series Bedienungsanleitung

Cisco

Cisco C3230-1W-49-K9 - 3230 WMIC Card Bundle... Anwendungshandbuch

Cisco

Cisco CISCO7301 Originalbetriebsanleitung

Cisco

Cisco 2851 - Integrated Services Router Bedienungsanleitung

Cisco

Cisco 7505 Bedienungsanleitung

Cisco

Cisco 12000 GSR Series Service-Handbuch

Cisco

Cisco WS-C4507R Betriebsanleitung

Cisco

Cisco ASR 5000 Series Bedienungs- und Sicherheitshinweise

Cisco

Cisco ME-C6524GS-8S Bedienungsanleitung

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Bedienungsanleitung

Cisco

Cisco RV120W Bedienungsanleitung

Cisco

Cisco 1003 Bedienungsanleitung

Cisco

Cisco CCNA 2 Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco CRS Bedienungsanleitung

Cisco

Cisco 7609 Bedienungsanleitung

Cisco

Cisco 1417 Bedienungsanleitung

Cisco

Cisco CSS11501S-C-K9 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung