Cisco Catalyst 9500 Series Betriebsanleitung

Troubleshooting

•Getting Started, on page 1

•Solving Problems at the System Component Level, on page 1

•Identifying Startup Problems, on page 2

•Troubleshooting the Power Supply, on page 2

•Troubleshooting the Fan Tray , on page 3

•Status LED Indicators, on page 3

•Contacting Cisco Customer Service, on page 3

•Finding the Serial Number, on page 4

Getting Started

When the initial system startup is complete, verify the following:

• Power supplies are supplying power to the system.

• The fan tray assembly is operating.

• System software boots successfully.

If one or more of the above conditions are not met, use the procedures described in this chapter to isolate and,

if possible, resolve the problem. If all of the above conditions are met, and the hardware installation is complete,

refer to your software release notes for hardware support information and software caveats.

Solving Problems at the System Component Level

The key to success when troubleshooting the system is to isolate the problem to a specific system component.

The first step is to compare what the system is doing to what it should be doing. Because a startup problem

can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather

than troubleshoot each separate component in the system.

The switch consists of these subsystems:

• Power supplies

• Fan tray assembly

Troubleshooting

The chassis fan tray assembly should operate whenever system power is on. You should see the FAN

LED turn green and hear the fan tray assembly operating. A red or amber FAN LED indicates that one

or more fans in the fan tray assembly is not operating. You should immediately contact a Customer

Service representative if the fan tray assembly is not functioning properly. There are no installation

adjustments that you can make if the fan tray assembly does not function properly at initial startup.

Identifying Startup Problems

LEDs indicate all system states in the startup sequence. By checking the LEDs, you can determine when and

where the system failed in the startup sequence.

Procedure

Step 1 Turn on the power supplies. You should immediately hear the system fan tray assembly begin to operate.

Step 2 If the startup information and system banner do not display at startup, verify that the terminal is set correctly

and that it is connected properly to the console port.

Troubleshooting the Power Supply

If the Power Supply LED does not light after you turn on the power switch, follow these steps to isolate a

power subsystem problem:

Procedure

Step 1 Verify that the Power Supply LED on the power supply is green.

• If the Power Supply LED is green, the AC or DC source is good and the power supply is functional.

• If the Power Supply LED remains off, there might be a problem with the AC source, the DC source, or

the power cable.

• Turn off the power to the switch, connect the power cord to another power source if one is available, and

turn on the power.

• If the Power Supply LED is green, the problem is the first power source.

• If the Power Supply LED fails to light after you connect the power supply to a new power source, replace

the power cord, and turn on the switch.

• If the Power Supply LED then goes on, return the first power cord for replacement.

If this unit has more than one power cord, repeat Step 1 for each power supply.

If the Power Supply LED still fails to light when the switch is connected to a different power source with a

new power cord, the power supply is probably faulty.

Troubleshooting

Identifying Startup Problems

If a second power supply is available, install it in the second power supply bay, and contact a customer service

representative for further instructions.

Step 2 If you have a second power supply, repeat Step 1 for this power supply.

What to do next

If you are unable to resolve the problem or if you determine that either a power supply or backplane connector

is faulty, see Contacting Cisco Customer Service, on page 3.

Troubleshooting the Fan Tray

To isolate a fan tray problem, follow these steps:

Procedure

Step 1 Verify that the FAN LED on the fan tray is green.

If the FAN LED is not green, see Fan LED to determine whether or not the power subsystem is functioning

properly.

Step 2 Check to determine if the FAN LED is red or amber. If the FAN LED is red, one or more fans' tachometer

faults have exceeded the maximum limit. If the FAN LED is amber, one or more fans have encountered

tachometer faults.

Do the following:

• To ensure that the fan tray is seated properly, loosen the captive installation screws, remove the fan tray,

and reinstall it.

• Tighten all captive installation screws, and then restart the system.

• If the FAN LED is still red or amber, the system detects an individual fan failure. Contact a customer

service representative for instructions.

Status LED Indicators

Refer to "System LED" section in the "Product Overview" chapter. More details will be added here later.

Contacting Cisco Customer Service

If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contact

a Cisco customer service representative for assistance and additional instructions. Before you call, have the

following information ready to help your service provider assist you as quickly as possible:

Troubleshooting

Troubleshooting the Fan Tray

• Date on which you received the switch

• Chassis serial number

• Type of software and release number

• Maintenance agreement or warranty information

• Brief description of the problem

• Brief explanation of the steps you have already taken to isolate and resolve the problem

Finding the Serial Number

If you contact Cisco Technical Assistance, you need to know the switch serial number. The figure shows

where the serial number is located. You can also use the show version privileged EXEC command to see the

serial number.

Figure 1: Serial Number Location and Switch Labels

Serial number of the switch is located at the top of the switch. Following illustrations show all the labels at

the top and the bottom of the switch.

Serial Number6Mult1 Power Warning1

Laser Warning7Fan Tray Warning2

Caution ESD8RFID3

Lab Altitude9CLEI4

Compliance label10MAC Number5

Troubleshooting

Finding the Serial Number

Andere Handbücher für Catalyst 9500 Series

Inhaltsverzeichnis

Andere Cisco Schalten Handbücher

Cisco

Cisco Nexus 3000 series Bedienungsanleitung

Cisco

Cisco Catalyst 3650 Bedienungsanleitung

Cisco

Cisco ME 3400 Series Bedienungsanleitung

Cisco

Cisco Catalyst WS-C3850-24T-L Bedienungs- und Sicherheitshinweise

Cisco

Cisco 2950 - Catalyst Switch Installationshandbuch

Cisco

Cisco IE 3010 Bedienungsanleitung

Cisco

Cisco 3750 - Catalyst EMI Switch Bedienungsanleitung

Cisco

Cisco NCS 4200 Series Bedienungsanleitung

Cisco

Cisco MDS 9000 Series Bedienungsanleitung

Cisco

Cisco Cisco Industrial Ethernet 3000 Series Bedienungsanleitung

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Bedienungsanleitung

Cisco

Cisco Nexus 4001I Bedienungsanleitung

Cisco

Cisco Catalyst Express 500 Technisches Dokument

Cisco

Cisco Catalyst 2960 Series Bedienungsanleitung

Cisco

Cisco 3750 - Catalyst EMI Switch Bedienungsanleitung

Cisco

Cisco 3750 - Catalyst EMI Switch Bedienungsanleitung

Cisco

Cisco Catalyst 3030 Bedienungsanleitung

Cisco

Cisco SF-300-24P - Bedienungsanleitung

Cisco

Cisco Nexus 6000 Bedienungsanleitung

Cisco

Cisco Small Business 200 Series Bedienungsanleitung

Cisco

Cisco MDS 9000 Series Bedienungsanleitung

Cisco

Cisco SD216 Bedienungsanleitung

Cisco

Cisco Catalyst 3650 Series Bedienungsanleitung

Cisco

Cisco Catalyst 9500 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung