Cisco N9K-C93180YC-FX Bedienungsanleitung

Configuring N Port Virtualization

This chapter contains the following sections:

•Supported Hardware, page 1

•FC NPV Overview, page 2

•FC NPV Mode, page 2

•Server Interfaces, page 3

•NP Uplinks, page 3

•SAN Port Channels, page 4

•FLOGI Operation, page 9

•NPV Traffic Management, page 10

•FC NPV Traffic Management Guidelines, page 11

•FC NPV Guidelines and Limitations, page 11

•Licensing Requirements for FC NPV, page 13

•Configuring NPV, page 13

•Verifying FC NPV, page 19

•FC NPV Core Switch and FC NPV Edge Switch Configuration Example, page 22

Supported Hardware

FC NPV is supported on the N9K-C93180YC-FX switch and only the following FC SFPs are supported:

•DS-SFP-FC8G-SW

•DS-SFP-FC16G-SW

•DS-SFP-FC32G-SW

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

DS-SFP-FC32G-SW operates at 16G speed.Note

FC NPV Overview

A switch is in NPV mode after enabling NPV. NPV mode applies to an entire switch. All end devices connected

to a switch that are in NPV mode must log in as an N port to use this feature (loop-attached devices are not

supported). All links from the edge switches (in NPV mode) to the NPV core switches are established as NP

ports (not E ports), which are used for typical inter-switch links. NPIV is used by the switches in NPV mode

to log in to multiple end devices that share a link to the NPV core switch.

The following figure shows an interface-level view of an FC NPV configuration.

Figure 1: FC NPV Interface Configuration

FC NPV Benefits

FC NPV provides the following:

•Increased number of hosts that connect to the fabric without adding domain IDs in the fabric

•Connection of FC and FCoE hosts and targets to SAN fabrics using FC interfaces

•Automatic traffic mapping

•Static traffic mapping

FC NPV Mode

In FC NPV mode, the edge switch relays all traffic to the core switch and shares the domain ID of the core

switch.

FC NPV is enabled by installing and enabling feature-set fcoe-npv. You cannot configure FC NPV mode

on a per-interface basis. FC NPV mode applies to the entire switch.

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

FC NPV Overview

Server Interfaces

•In Cisco Nexus 9000 Series switches, server interfaces can be FC or vFC interfaces.

•Server interfaces are F ports on the edge switch that connect to the servers. A server interface may

support multiple end devices by enabling the N port identifier virtualization (NPIV) feature. NPIV

provides a means to assign multiple FC IDs to a single N port, which allows the server to assign unique

FC IDs to different applications.

To use NPIV, enable the NPIV feature and reinitialize the server interfaces that will

support multiple devices.

Note

•FC server interfaces should be in trunk mode off. Trunk mode on is not supported.

•vFC server interfaces should be in trunk mode on.

•Server interfaces are automatically distributed among the NP uplinks to the core switch. All of the end

devices connected to a server interface are mapped to the same NP uplink.

•8 G speed is not supported for server and target interfaces.

•The default speed is 16 G.

NP Uplinks

•In Cisco Nexus 9000 Series switches, NP uplink interfaces can be native Fibre Channel interfaces, virtual

fiber channel interfaces, SAN port channel interfaces, or virtual ethernet port-channel interfaces.

•All interfaces from the edge switch to the core switch are configured as proxy N ports (NP ports).

•An NP uplink is a connection from an NP port on the edge switch to an F port on the core switch. When

an NP uplink is established, the edge switch sends a fabric login message (FLOGI) to the core switch

then (if the FLOGI is successful) registers itself with the name server on the core switch. Subsequent

FLOGIs from end devices connected to this NP uplink are forwarded as-is to the core switch. Subsequent

flags from the same VSAN are forwarded as fdisc.

In the switch CLI configuration commands and output displays, NP uplinks are called

External Interfaces.

Note

•The features below must be enabled on the core switch:

◦feature npiv

◦feature fport-channel-trunk

•If the FC uplink speed is 8 G, the fill pattern should be configured as IDLE on the core switch.

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

Server Interfaces

Following is an example of configuring IDLE fill pattern on a Cisco MDS switch:

Switch(config)# int fc2/3

Switch(config)# switchport fill-pattern IDLE speed 8000

Switch(config)# sh run int fc2/3

interface fc2/3

switchport speed 8000

switchport mode NP

switchport fill-pattern IDLE speed 8000

no shutdown

Note

Note •For the FLOGI from NP uplink of Cisco Nexus 9000 Series switches to be successful on the core

switch, the core should be configured with the OUI of a Cisco Nexus 9000 Series switch. Configure

the OUI on the core only if the core has not registered the OUI by default.

The OUI is found and configured as follows:

N9K(config-if)# show wwn switch

Switch WWN is 20:00:2c:d0:2d:50:ea:64

N9K(config-if)#

On the core, we see the output below if the OUI (0x2cd02d) is already registered.

MDS9710(config-if)# sh wwn oui | i 2cd02d

0x2cd02d Cisco Default

MDS9710(config-if) #

If the OUI is not registered with the core, configure it manually.

MDS9710(config-if)# wwn oui 0x2cd02d

•Beginning in Cisco NX-OS Release 7.3(3)N1(1), the OUI is configurable on a Cisco Nexus 6000

Series core switch.

SAN Port Channels

About SAN Port Channels

•A SAN port channel is a logical interface that combines a set of FC interfaces connected to the same

fibre channel node and operates as one link.

•SAN port channels support bandwidth utilization and availability.

•SAN port channels on Cisco Nexus 9000 Series switches are mainly used to connect to MDS cores and

to provide optimal bandwidth utilization and transparent failover between the uplinks of a VSAN.

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

SAN Port Channels

Configuring SAN Port Channels

SAN port channels are created with default values. You can change the default configuration just as any other

physical interface.

If the following requirements are not met, a SAN port channel error is detected:

•Each switch on either side of a SAN port channel must be connected to the same number of interfaces.

•Each interface must be connected to a corresponding interface on the other side.

•Links in a SAN port channel cannot be changed after the port channel is configured. If you change the

links after the port channel is configured, be sure to reconnect the links to interfaces within the port

channel and reenable the links.

If all three conditions are not met, the faulty link is disabled. Enter the show interface command for that

interface to verify that the SAN port channel is functioning as required.

Note

SAN Port Channel Guidelines and Limitations

•The number of SAN port channels and virtual FC port channels, together, can be only 8 on the Cisco

Nexus 9000 Series switch.

•The maximum number of FC interfaces that can be combined into a SAN port channel is limited to 16.

•The default channel mode on Cisco Nexus 9000 Series switches for SAN port channels is active; this

cannot be changed.

Creating a SAN Port Channel

This section explains how to create a SAN port channel.

Procedure

Step 1 switch# configuration terminal

Enters the global configuration mode.

Step 2 switch(config)# interface san-port-channel channel-number

Creates the specified SAN port channel using the default mode (on). The SAN port channel number is in the

range of 1 to 256

The following example shows the SAN port channel creation:

switch(config)# interface san-port-channel 1

switch(config-if)#

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

Configuring SAN Port Channels

About SAN Port Channel Modes

A SAN port channel is configured with channel mode active by default. When active, the member ports initiate

port-channel-protocol negotiation with the peer port(s) regardless of the channel-group mode of the peer port.

If the peer port, while configured in a channel group, does not support the port-channel protocol, or responds

with a nonnegotiable status, the port channel will be disabled. The active port -channel mode allows automatic

recovery without explicitly enabling and disabling the port-channel-member ports at either end.

About Deleting SAN Port Channels

When you delete the SAN port channel, the corresponding channel membership is also deleted.

If you delete the SAN port channel for one port, then the individual ports within the deleted SAN port channel

retain the compatibility parameter settings (speed, mode, port VSAN, allowed VSAN, and port security). You

can explicitly change those settings as required.

Deleting SAN Port Channels

This section explains how to delete a SAN port channel.

Procedure

Step 1 switch# configuration terminal

Enters global configuration mode.

Step 2 switch(config)#no interface san-port-channel channel-number

Deletes the specified port channel, its associated interface mappings, and the hardware associations for this

SAN port channel.

The following example demonstrates how to delete a SAN port channel:

switch(config)# no interface san-port-channel 1

The SAN port channel 1 is deleted and all its members are disabled. Please do the same operation on the

switch at the other end of the SAN port channel.

Interfaces in a SAN Port Channel

You can add or remove a physical Fibre Channel interface (or a range of interfaces) to an existing SAN port

channel. The compatible parameters on the configuration are mapped to the SAN port channel. Adding an

interface to a SAN port channel increases the channel size and bandwidth of the SAN port channel. Removing

an interface from a SAN port channel decreases the channel size and bandwidth of the SAN port channel.

Virtual Fibre Channel interfaces cannot be added to SAN port channels.Note

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

Interfaces in a SAN Port Channel

Adding an Interface to a SAN Port Channel

This section explains how to add an interface to a SAN port channel.

Procedure

Step 1 switch#configuration terminal

Enters global configuration mode.

Step 2 switch(config)# interface type slot /port

Enters configuration mode for the specified interface.

Step 3 switch(config-if)#channel-group channel-number

Adds the Fibre Channel interface to the specified channel group. If the channel group does not exist, it is

created. The port is shut down.

The following example adds an interface to a SAN port channel:

switch(config)# interface fc2/3

switch(config-if)# channel-group 15

fc2/3 is added to san-port-channel 15 and is disabled. Please do the same operation on the switch at the other

end of the san-port-channel, then do “no shutdown”at both ends to bring them up

Forcing an Interface Addition

You can force the port configuration to be overwritten by the SAN port channel. In this case, the interface is

added to a SAN port channel.

When SAN port channels are created from within an interface, the force option cannot be used.Note

This section explains how to force the addition of a port to a SAN port channel.

Procedure

Step 1 switch# configuration terminal

Enters global configuration mode.

Step 2 switch(config)#interface type slot / port

Enters configuration mode for the specified interface.

Step 3 switch(config-if)# channel-group channel-number force

Forces the addition of the interface into the specified channel group. The E port is shut down.

The following example adds an interface to a SAN port channel:

switch(config)# interface fc2/3

switch(config-if)# channel-group 15 force

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

Interfaces in a SAN Port Channel

fc2/3 added to san-port-channel 15 and disabled. Please do the same operation on the switch at the other end

of the san-port-channel, then perform a no shutdown at both ends to bring them up

About Interface Deletion from a SAN Port Channel

When a physical interface is deleted from the SAN port channel, the channel membership is automatically

updated. If the deleted interface is the last operational interface, then the port channel status is changed to a

down state. Deleting an interface from a SAN port channel decreases the channel size and bandwidth of the

SAN port channel.

Deleting an Interface from a SAN Port Channel

This section explains how to delete a physical interface (or a range of physical interfaces) from a SAN port

channel.

Procedure

Step 1 switch(config)# interface type slot /port

Enters configuration mode for the specified interface.

Step 2 switch(config)#no channel-group channel-number

Deletes the physical Fibre Channel interface from the specified channel group.

The following example deletes an interface from a SAN port channel:

switch(config)# interface fc2/3

witch(config-if)# no channel-group 15

fc2/1 is removed from the SAN port-channel 2 and disabled.

Please do the same operation on the switch at the other end of the san-port-channel

Verifying SAN Port Channel Configurations

You can view specific information about existing SAN port channels at any time from EXEC mode. The

following show commands provide further details on existing SAN port channels.

The show san-port-channel summary command displays a summary of SAN port channels within the switch.

A one-line summary of each SAN port channel provides the administrative state, the operational state, the

number of attached and active interfaces (up), and the first operational port (FOP), which is the primary

operational interface selected in the SAN port channel to carry control-plane traffic (no load-balancing). The

FOP is the first port that comes up in a SAN port channel and can change if the port goes down. The FOP is

also identified by an asterisk ( *).

To display VSAN configuration information, perform one of the following tasks:

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

Verifying SAN Port Channel Configurations

Procedure

Step 1 switch# show san-port-channel summary |database |consistency [details ] | usage |

compatibility-parameters

Displays SAN port channel information.

Step 2 switch# show san-port-channel database interface san-port-channel channel-number

Displays information for the specified SAN port channel.

Step 3 switch# show interface fc slot / port

Displays VSAN configuration information for the specified Fibre Channel interface.

The following example shows how to display a summary of SAN port channel information:

switch# show san-port-channel summary

------------------------------------------------------------------------------

Interface Total Ports Oper Ports First Oper Port-

san-port-channel 7 2 0 –

san-port-channel 8 2 0 –

san-port-channel 9 2 2

The following example shows how to display SAN port channel consistency:

switch# show san-port-channel consistency

Database is consistent

The following example shows how to display details of the used and unused port channel numbers:

switch# show san-port-channel usage

Totally 3 port-channel numbers used===================================Used : 77 - 79Unused:

1 - 76, 80 - 256

FLOGI Operation

When an NP port becomes operational, the switch first logs itself in to the core switch by sending a FLOGI

request (using the port WWN of the NP port).

After completing the FLOGI request, the switch registers itself with the fabric name server on the core switch

(using the symbolic port name of the NP port and the IP address of the edge switch).

The following table identifies port and node names in the edge switch used in FC NPV mode.

Table 1: Edge Switch FLOGI Parameters

Derived FromParameter

The fWWN of the NP port on the edge switch.pWWN

The VSAN-based sWWN of the edge switch.nWWN

The edge switch name and NP port interface string.

If no switch name is available, the output

will read "switch." For example, switch: fc

1/5.

Note

symbolic port name

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

FLOGI Operation

Derived FromParameter

The IP address of the edge switch.IP address

The edge switch name.symbolic node name

NPV Traffic Management

Automatic Uplink Selection

NPV supports automatic selection of NP uplinks. When a server interface is brought up, the NP uplink interface

with the minimum load is selected from the available NP uplinks in the same VSAN as the server interface.

When a new NP uplink interface becomes operational, the existing load is not redistributed automatically to

include the newly available uplink. Server interfaces that become operational after the NP uplink can select

the new NP uplink.

Traffic Maps

In Release 7.0(3)I7(2) and later software releases, FC NPV supports traffic maps. A traffic map allows you

to specify the NP uplinks that a server interface can use to connect to the core switches.

When an FC NPV traffic map is configured for a server interface, the server interface must select only

from the NP uplinks in its traffic map. If none of the specified NP uplinks are operational, the server

remains in a non-operational state.

Note

The FC NPV traffic map feature provides the following benefits:

•Facilitates traffic engineering by allowing configuration of a fixed set of NP uplinks for a specific server

interface (or range of server interfaces).

•Ensures correct operation of the persistent FC ID feature; this is because a server interface will always

connect to the same NP uplink (or one of a specified set of NP uplinks) after an interface reinitialization

or switch reboot.

•Enables an external interface to be an individual link or SAN port channel.

Disruptive Auto Load Balancing of Server Logins across NP Links

In Release 7.0(3)I7(2) and later software releases, FC NPV supports disruptive load balancing. When disruptive

load balancing is enabled, FC NPV redistributes the server interfaces across all available NP uplinks when a

new NP uplink becomes operational. To move a server interface from one NP uplink to another NP uplink,

FC NPV forces reinitialization of the server interface so that the server performs a new login to the core switch.

Cisco Nexus 9000 Series NX-OS FC NPV Configuration Guide

Configuring N Port Virtualization

NPV Traffic Management

Inhaltsverzeichnis

Andere Cisco Schalten Handbücher

Cisco

Cisco WS-C3750-48PS-S Bedienungsanleitung

Cisco

Cisco 3750 - Catalyst EMI Switch Installationshandbuch

Cisco

Cisco 4948 Series Bedienungsanleitung

Cisco

Cisco Aironet 350 Series Bedienungsanleitung

Cisco

Cisco SG 100D-08 Bedienungsanleitung

Cisco

Cisco SRW2008 - Small Business Managed Switch Bedienungsanleitung

Cisco

Cisco Nexus 9348GC-FXP-B1 Handbuch

Cisco

Cisco MDS 9148T Handbuch

Cisco

Cisco Nexus 5548P Bedienungsanleitung

Cisco

Cisco Catalyst 3550 Bedienungsanleitung

Cisco

Cisco 3750 - Catalyst EMI Switch Merkblatt

Cisco

Cisco IE-3010-16S-8PC Handbuch

Cisco

Cisco SFS InfiniBand Server Switch SFS 7000P Handbuch

Cisco

Cisco Nexus 3400 Series Handbuch

Cisco

Cisco Catalyst X4424 Bedienungsanleitung

Cisco

Cisco Nexus 7000 Series Bedienungsanleitung

Cisco

Cisco OL-4419-06 Bedienungsanleitung

Cisco

Cisco Small Business SF200-24 Bedienungsanleitung

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Installations- und Betriebshandbuch

Cisco

Cisco SR2024 - Small Business Unmanaged Switch Bedienungsanleitung

Cisco

Cisco UCS 6100 Series Systemhandbuch

Cisco

Cisco SF250-24-K9 Bedienungsanleitung

Cisco

Cisco Catalyst 6800 Series Bedienungsanleitung

Cisco

Cisco IE 2000 Anleitung zur Verwendung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung