Cisco WAP351 Leitfaden

Andere Handbücher für WAP351

1

Inhaltsverzeichnis

Andere Cisco Drahtloser Zugangspunkt Handbücher

Cisco

Cisco MERAKI MR72 Bedienungsanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco Small Business WAP551 Bedienungsanleitung

Cisco

Cisco WAP121 Bedienungsanleitung

Cisco

Cisco WAP371 Bedienungsanleitung

Cisco

Cisco AIR-LAP1252AG-A-K9 - Aironet 1252AG - Wireless Access... Bedienungsanleitung

Cisco

Cisco Meraki Go GR10 Bedienungsanleitung

Cisco

Cisco Catalyst IW6300 Series Handbuch

Cisco

Cisco Aironet 2600 Series Bedienungsanleitung

Cisco

Cisco ASA 5508-X Handbuch

Cisco

Cisco Aironet 1815T Bedienungsanleitung

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Bedienungsanleitung

Cisco

Cisco Catalyst 9164 Series Bedienungsanleitung

Cisco

Cisco Aironet 1140 Series Bedienungsanleitung

Cisco

Cisco Aironet LAP1522 Handbuch

Cisco

Cisco Meraki GR60 Bedienungsanleitung

Cisco

Cisco MERAKI MR44 Bedienungsanleitung

Cisco

Cisco Aironet 1520 Series Bedienungsanleitung

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Handbuch

Cisco

Cisco Linksys WAP55AG Bedienungsanleitung

Cisco

Cisco WAP125 Bedienungsanleitung

Cisco

Cisco AIR-CAP3502I-A-K9 Bedienungsanleitung

Cisco

Cisco 1522AG - Aironet Lightweight Outdoor Mesh Access... Bedienungsanleitung

Cisco

Cisco AIR-CAP1552H-x-K9 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

Reboot and Reset Factory Default Settings on

the WAP351

Objective

Rebooting a device is used to shut down and restart the device with a saved configuration.

The factory default is used to restore the factory default configuration on the device to

remove any previous configurations.

The objective of this document is to show you how to reboot your WAP351 device and reset

it to the factory default.

Applicable Devices

• WAP351

Software Version

• 1.0.0.39

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press and hold the Reset button located at the back of the device for approximately

ten seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log into the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the Power button to turn off the device. After 10 seconds have passed, press

the Power button a second time to power the device back on.

The Access Point reboots.

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login Page appears. Login with the saved administration credentials.