Cisco ASR 9010 Bedienungsanleitung

Unpacking and Installing the Chassis

This chapter describes how to unpack and install the chassis into a rack.

•Pre-Installation Considerations and Requirements, on page 1

•Installation Overview, on page 1

•Unpacking the Router, on page 3

•Removing Components Before Installing the Chassis, on page 20

•Rack-Mounting the Router Chassis, on page 48

•Supplemental Bonding and Grounding Connections, on page 64

•Installing Chassis Accessories, on page 68

Pre-Installation Considerations and Requirements

Before you perform any procedures in this chapter, review the following sections:

Observe the guidelines for preventing electrostatic discharge (ESD) damage described in Preventing Electrostatic

Discharge Damage.

See the Regulatory Compliance and Safety Information for the Cisco ASR 9000 Series Router document for

additional safety and compliance information,

This router is not designed to be installed as a shelf-mounted or a free-standing router. The router must be

installed in a rack that is secured to the building structure. You must install the router in either a telco-style

frame or a 4-post equipment rack.

Caution

Installation Overview

The following figure shows how the Cisco ASR 9010 Router is shipped and strapped to a shipping pallet.

Unpacking and Installing the Chassis

Figure 1: Cisco ASR 9010 Router Packaged on a Shipping Pallet

A fully equipped router with six power modules can weigh as much as 375 lbs (170.5 kg); an empty chassis

weighs 150 lbs (67.8 kg). The chassis is designed to be lifted by two persons after you remove some of the

components, such as line cards, power supplies, and the fan tray, to reduce the weight before lifting the chassis.

See Removing Components Before Installing the Chassis, on page 20 for procedures to remove these

components.

Required Tools and Equipment

Before you begin the rack-mount installation, you must read and understand the information in the

Rack-Mounting and Air Flow Clearance Guidelines, page 1-24 , and have the following tools and equipment:

• ESD-preventive wrist strap

• Number 1 and number 2 Phillips screwdrivers

• 1/4-inch (6.35-mm) and 3/16-inch (4.5-mm) flat-blade screwdrivers

• Tape measure

• Level (optional)

Unpacking and Installing the Chassis

Required Tools and Equipment

• Minimum of 10 slotted binderhead screws (usually provided with the rack) to secure the chassis to the

mounting flanges (also called rails ) in the rack. Five screws should be installed on each side of the

chassis.

• 11/16-inch (17.46-mm) wrench (for chassis hold-down bolts and pallet hold-down bracket bolts)

• 3/4-inch (19-mm) socket and ratchet wrench

Unpacking the Router

The following instructions describe how to unpack the Cisco ASR 9000 Series Router from its shipping

container.

Unpacking the Cisco ASR 9006 Router

Follow these steps to unpack the Cisco ASR 9006 Router from its shipping container (see the figure below).

Procedure

Step 1 Cut the straps that secure the cardboard shipping container to the pallet.

Step 2 Remove the cardboard shipping container.

Step 3 Remove the packaging material (see the figure below).

a) Remove the foam packaging material from the top of the router.

b) Remove all screws that secure the four hold-down brackets to the router chassis. The forward hold-down

brackets are secured to the router mounting brackets by two screws. The rear hold-down brackets are

secured to the chassis by four screws.

c) Remove two bolts per hold-down bracket that secure the brackets to the pallet.

Unpacking and Installing the Chassis

Unpacking the Router

Figure 2: Unpacking the Cisco ASR 9006 Router from the Shipping Container and Pallet

Chassis accessories7Cardboard

packaging container

4Top cardboard

packaging cap

Foam packaging

material- top cap

8Cardboard accessory

tray

5Three packaged

power modules

Hold-down brackets

(four places)

9Accessories and

power cables

6Cardboard

packaging dividers

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9006 Router

Step 4 Remove components, such as line cards, power supplies, and the fan tray, to reduce the weight before lifting

or moving the chassis. See Removing Components Before Installing the Chassis, on page 20 for more

information.

Step 5 Save the packaging materials in case the router needs repackaging or shipping.

Unpacking the Cisco ASR 9010 Router

Follow these steps to unpack the Cisco ASR 9010 Router from its shipping container.

Procedure

Step 1 Cut the straps that secure the cardboard shipping container to the pallet.

Step 2 Remove the cardboard shipping container.

Step 3 Remove the packaging material.

a) Remove the foam packaging material from the top of the router.

b) Remove all screws that secure the four hold-down brackets to the router chassis. The forward hold-down

brackets are secured to the router mounting brackets by two screws. The rear hold-down brackets are

secured to the chassis by four screws. Save these four screws used to hold the rear bracket to the chassis

to use later to attach the ground strap.

Step 4 Remove two bolts per hold-down bracket that secure the brackets to the pallet.

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9010 Router

Figure 3: Unpacking the Cisco ASR 9010 Router from the Shipping Container and Pallet

Rear hold-down

bracket secured

by four screws to

the chassis, and

by two bolts to

the pallet (two

places)

3Front hold-down

bracket secured

by two screws to

the chassis

mounting

brackets, and by

two bolts to the

pallet (two

places)

2Foam packaging

material- top cap

Step 5 Remove components, such as line cards and the fan tray, to reduce the weight before lifting or moving the

chassis. See the Removing Components Before Installing the Chassis for more information.

Step 6 Save the packaging materials in case the router needs repackaging or shipping.

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9010 Router

Unpacking the Cisco ASR 9904 Router

Follow these steps to unpack the Cisco ASR 9904 Router from its wooden shipping container.

Procedure

Step 1 Cut the straps that secure the cardboard shipping container to the pallet.

Step 2 Remove the corrugated top shipping container.

Step 3 Remove the accessories and corrugated packing accessory tray.

Step 4 Remove the packing material (see the figure below).

a) Remove the foam packaging material from the top of the router.

b) Remove the plastic covering from the router and remove it from the bottom foam.

Figure 4: Unpacking the Cisco ASR 9904 Router from the Shipping Container and Pallet

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9904 Router

Cardboard shipping

container

7Foam packaging

material(top cap)

4Shipping pallet1

Foam packaging

material (bottom

cap)

5Top corrugated

packaging cap

Corrugated

packaging (lower

tray)

6Corrugated

packaging accessory

tray

Step 5 Remove components, such as line cards, power supplies, and the fan tray, to reduce the weight before lifting

or moving the chassis. See Removing Components Before Installing the Chassis, on page 20 for more

information.

Step 6 Save the packaging materials in case the router needs repackaging or shipping.

Unpacking the Cisco ASR 9906 Router

Follow these steps to unpack the Cisco ASR 9906 Router from its shipping container (see the figure below).

Procedure

Step 1 Cut the straps that secure the cardboard shipping container to the pallet.

Step 2 Remove the three connecting clips.

Step 3 Remove the cardboard shipping container.

Step 4 Remove the accessory tray and chassis accessories.

Step 5 Remove the packaging material (see the figure below).

a) Remove the foam packaging material from the top of the router.

b) Remove all screws that secure the two hold-down brackets to the router chassis.

c) Remove four bolts per hold-down bracket that secure the brackets to the pallet.

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9906 Router

Figure 5: Unpacking the Cisco ASR 9906 Router from the Shipping Container and Pallet

Shipping pallet5Straps1

Hold-down bracket and

screws

6Connecting clips2

Cardboard accessory tray

and chassis accessories

7Top cardboard packaging

cap

Cardboard packaging

container

8Foam packaging material4

Step 6 Remove components, such as line cards, power supplies, and the fan tray, to reduce the weight before lifting

or moving the chassis. See Removing Components Before Installing the Chassis, on page 20 for more

information.

Step 7 Save the packaging materials in case the router needs repackaging or shipping.

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9906 Router

Unpacking the Cisco ASR 9910 Router

Follow these steps to unpack the Cisco ASR 9910 Router from its shipping container.

Procedure

Step 1 Cut the straps that secure the cardboard shipping container to the pallet.

Step 2 Remove the cardboard shipping container.

Step 3 Remove the packaging material (see the figure below).

a) Remove the foam packaging material from the top of the router.

b) Remove all screws that secure the two brackets to the router chassis. Save these screws used to hold the

bracket to the chassis to use later to attach the ground strap.

Step 4 Remove two bolts per hold-down bracket that secure the brackets to the pallet.

Unpacking and Installing the Chassis

Unpacking the Cisco ASR 9910 Router

Dieses Handbuch passt für folgende Modelle

Andere Cisco WLAN-Router Handbücher

Cisco

Cisco 3750G - Catalyst Integrated Wireless LAN... Bedienungsanleitung

Cisco

Cisco Linksys E900 Bedienungsanleitung

Cisco

Cisco Linksys WRT120N Bedienungsanleitung

Cisco

Cisco 3230 Bedienungsanleitung

Cisco

Cisco EPC3925 Bedienungsanleitung

Cisco

Cisco 3825 Series Bedienungsanleitung

Cisco

Cisco MERAKI mx60 Bedienungsanleitung

Cisco

Cisco LINKSYS WRT54GX4 Bedienungsanleitung

Cisco

Cisco Small Business WRP400 Bedienungsanleitung

Cisco

Cisco UBR7246VXR Bedienungsanleitung

Cisco

Cisco Linksys EA2700 Bedienungsanleitung

Cisco

Cisco T-Mobile HIPORT+ Bedienungsanleitung

Cisco

Cisco Linksys WAG54G2 Bedienungsanleitung

Cisco

Cisco Linksys E1000 Bedienungsanleitung

Cisco

Cisco BBSM 1 Bedienungsanleitung

Cisco

Cisco SRP521W Bedienungsanleitung

Cisco

Cisco RV134W Bedienungsanleitung

Cisco

Cisco 4402 - Wireless LAN Controller Leitfaden

Cisco

Cisco RB-WRT54GS2 - Wireless-G Broadband Router Bedienungsanleitung

Cisco

Cisco Catalyst IR1800 Rugged Series Bedienungsanleitung

Cisco

Cisco Catalyst IR1800 Rugged Series Kurzanleitung

Cisco

Cisco WRT54G2 Linksys Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco Small Business RV315W Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Milesight

Milesight UG67 Bedienungsanleitung

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

NETGEAR

NETGEAR WNR2000v4 Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung