Cissell ACDCMAN407 Bedienungsanleitung

Page 1

MAN407 2/97

Automatic

Computer

Drying

SUPPLEMENTAL

OWNER’S MANUAL

THIS MANUAL MUST BE GIVEN TO THE EQUIPMENT OWNER.

CISSELL MANUFACTURING COMPANY

HEADQUARTERS PHONE: (502) 587-1292

831 SOUTH FIRST ST. SALES FAX: (502) 585-3625

P.O. BOX 32270 SERVICE/PARTS FAX: (502) 681-1275

LOUISVILLE, KY 40232-2270

Page 2

DESCRIPTION

The Automatic Computer Drying Control is used to manage the drying and cooling

cycles of one clothes dryer. The operator has the flexibility to select either automatic or

timed drying and either automatic or timed cooling. When automatic is selected, the

drying cycle will be terminated when the clothes are dry. A dryness sensor "feels" the

clothes and signals the control when they are dry. In the timed mode, the operator sets

the time and temperature for the load.

FEATURES:

• Automatic/Timed drying selection.

• Automatic/Timed cooling selection.

• Fabric selection (in automatic mode only).

• LED display of cycle time.

• Drying temperature range of 100° F - 195° F (Timed mode only).

• Drying time range of 0-60 minutes (Timed mode only).

• Cooling time range of 0-60 minutes (Timed mode only).

• Repeat Last Cycle feature.

• Safety tumble cycle.

• Reversing/Non-reversing selection (option).

• Power off after 30 minutes of non-use.

Page 3

DESCRIPTION OF CONTROL PANEL

1. ON. Turn the control on.

2. OFF/STOP. Turns the control off.

3. START. Starts the cycle.

4. COOLING TIME. With this button held down, the cooling time in minutes will

be shown in the display. To change the time, use the “up” and “down” buttons.

(The cooling time cannot be changed when Automatic Cooling is selected, “-A-”

will show in the display when this button is held down.)

5. DRYING TIME. With this button held down, the drying time in minutes will be

shown in the display. To change the time, use the “up” and “down” buttons. (The

drying time cannot be changed when Automatic Drying is selected, “-A-” will show

in the display when this button is held down.)

6. DRYING TEMPERATURE. With this button held down, the drying

temperature in degrees F will be shown in the display. To change the

temperature, use the “up” and “down” buttons. (The drying temperature cannot

be changed when Automatic Drying is selected, the temperature associated with

the fabric selected will show in the display when this button is held down.)

7. FABRIC SELECTOR. Used to select the type of fabric to be dried when

Automatic Drying is selected. The fabric selection automatically sets the

temperature:

HEAVY .................. 195ºF

COTTON ................. 195ºF

PERMANENT PRESS ....... 175ºF

DELICATE................ 160ºF

8. DRYING. Pressing this button changes the selection of Automatic or Timed

Drying.

9. COOLING. Pressing this button changes the selection of Automatic or Timed

Cooling.

10. REPEAT LAST CYCLE. Pressing this button before the start of a cycle will reset

all of the selections, temperatures, and times to what they were at the beginning of

the last cycle.

11. NON-REVERSING/REVERSING. Pressing this button changes the selection of

Non-reversing and Reversing.

Page 4

CONTROL PANEL ILLUSTRATION

Page 5

DESCRIPTION OF CONTROL PANEL (cont’d)

12. LED Display. Shows cycle time. In Automatic, it shows the time used. In

Timed, it shows the time remaining. When the DRYING TEMPERATURE button

is pressed and held, the drying temperature will be displayed. When the DRYING

TIME button is pressed and held, either the total drying time or “-A-” will be

displayed depending on whether AUTO or TIMED drying has been selected.

When the COOLING TIME button is pressed and held, either the total cooling

time or “-A-” will be displayed depending on whether AUTO or TIMED cooling has

been selected.

13. DRYING. Illuminated when in the drying cycle.

14. COOLING. Illuminated when in the cooling cycle.

15. END OF CYCLE. Illuminated at the end of the cycle.

16. OPEN DOOR. Illuminated when the door is open. (START must be pressed to

restart the cycle after closing the door.)

DISPLAY

Display Condition

“__0” Normal display between loads. Dryer is waiting for the next

load.

“012” Normal display during drying/cooling cycle. Display shows

“time used” when in automatic and “time remaining” when in

timed mode.

“012” (flashing) The door has been opened. Close the door and press START

to continue the cycle.

“-S-” (flashing) The dryer is in the Safety Tumble mode. The cycle has ended

and the dryer can be unloaded.

“_PF” (flashing) There has been a power failure. To restart the dryer, press

ON and START. To terminate the cycle press OFF/STOP.

“FFF” (flashing) The temperature sensor has failed. The dryer cannot be run

until it is repaired.

“-A-” Indicates the automatic mode has been selected. (DRYING

TIME and COOLING TIME only).

Page 6

DETAILS OF CONTROL BOARD AND OPTIONS

Switch set #1

Switch ON OFF

#8 F/C Deg F Deg C

#7 SFTY-EN enabled disabled

#6 6-ADD + 6 Min. 0

#5 REPEAT S/E Start E n d

#4 2 DEG + 2 Deg. 0

#3 5 DEG + 5 Deg. 0

#2 10 DEG + 10 Deg. 0

#1 20 DEG + 20 Deg. 0

#8 F/C. Selection of Deg F or Deg C for temperature display. Position the

switch for the desired unit.

#7 SFTY-EN. The switch enables the “safety tumble” feature. To disable,

position this switch in the OFF position.

#6 6-ADD. Used in conjunction with the HEAVY fabric selection. When

switched to the “+ 6” position, an additional 6 minutes of drying time will

be added to the cycle when HEAVY has been selected. This is to

compensate for “hard to dry” loads or mixed loads.

#5 REPEAT S/E. This switch works in conjunction with the REPEAT LAST

CYCLE button. The parameters (mode, time, temperature) of the cycle will

be stored either at the START or the END of the cycle based on this switch

setting. The parameters that are stored will be used by the control when

the REPEAT LAST CYCLE button is pressed prior to starting a drying

cycle.

#4 2 DEG. Adds 2 Degrees to the differential temperature.

#3 5 DEG. Adds 5 Degrees to the differential temperature.

#2 10 DEG. Adds 10 Degrees to the differential temperature.

#1 10 DEG. Adds 10 Degrees to the differential temperature.

NOTE: The differential temperature is part of the heating logic. The heat turns off

when the temperature in the dryer reaches the temperature set for the

drying cycle. The temperature has to drop a set number of degrees below

the drying temperature before the heat will turn on. The difference

between the cycle temperature and the temperature to turn the heat on is

called the differential temperature. This control allows the differential to

be set between 5 and 25 degrees. The control “sums” the values set on the

switches but will not go lower than 5 nor greater than 25. If the sum is less

than 5 the control will default to 5. If the sum is greater than 25, the

control will default to 25.

Page 7

CONTROL BOARD AND OPTIONS ILLUSTRATION

Page 8

DETAILS OF CONTROL BOARD AND OPTIONS (cont’d)

Switch set #2

Switch ON OFF

#8 No Function ------

#7 No Function ------

#6 No Function ------

#5 No Function ------

#4 No Function ------

#3 No Function ------

#2 No Function ------

#1 No Function ------

Thermistor Calibration

To verify the calibration of the thermistor circuit, proceed as follows:

1. Disconnect the thermistor leads going to the circuit board.

2. Short the terminals at JP5 (thermistor calibration pins).

3. Press the “up arrow” and the “down arrow” keys to display the temperature.

4. The temperature should read 158

5. If not 158

F, adjust the thermistor calibration potentiometer until the display reads

158

6. Remove the jumper from the thermistor calibration pins.

7. Connect the thermistor leads to the circuit board.

Reversing Dwell Time

This potentiometer is used to set the dwell time when the dryer has the reversing option. The

dwell is the time from when the motor turns off to when it turns on again in the opposite

direction. Turning the knob counter-clockwise increases the dwell time and turning it clockwise

decreases the dwell time.

Computer Reset

Push this button if the control “locks up”. Pushing this button will reset the control.

120/230 Switch

This switch must be switched to the correct input voltage for the control to work. Applying 230

V when switched to the 120 V position will blow fuses on the circuit board.

Alarm Relay

A socket has been included to add a relay for an alarm to signal the end of the cycle. The

ALARM 1 and ALARM 2 terminals connect to the contacts of the relay. The relay energizes at

the end of the cycle and stays energized until either the door is opened or the dryer is turned

off.

Page 9

DETAILS OF OPERATION

Status Indicators (LED’s) and Buttons

ON. Turns the control on. The control has an Auto Power Off function. If the

dryer has not been used for 30 minutes, the control will turn itself off. Push ON

to turn the control back on.

OFF/STOP. Turns the control off or stops the dryer during a cycle.

START. Starts the cycle.

POWER. The control has power.

DRYING. The dryer is in the drying part of the cycle.

COOLING. The dryer is in the cooling part of the cycle.

END OF CYCLE. The cycle is complete. The dryer is ready for the next load.

DOOR OPEN. Indicates that the door is open. If the door is opened during a

cycle, the heat will turn off and the motors will stop. To restart the cycle, close

the door and press START. When the door is closed the display will flash the

current cycle time until the START button is pressed.

AUTO/TIMED. Indicates the selection of either an automatic or timed cycle.

Pushing either the DRYING or the COOLING buttons will “toggle” the selection

from AUTO to TIMED or from TIMED to AUTO.

FABRIC SELECTION. This functions in conjunction with the selection of the

AUTO DRYING mode. When AUTO DRYING is selected, a fabric must also be

selected. The control will not allow the cycle to start unless a fabric has been

selected. Pressing (or holding down) the FABRIC SELECTOR button will

sequence through the fabric selections. Stop when the light next to the fabric

desired is lit. The fabric selection automatically sets the drying temperature.

Heavy ........... 195

Cotton .......... 195

Permanent Press . 175

Delicate ......... 160

Page 10

DETAILS OF OPERATION (cont’d)

DRYING TEMPERATURE. In AUTO drying mode, pressing and holding this

button will show in the display the temperature (in Deg F) associated with the

fabric selection. In TIMED mode, pressing and holding this button will show in

the display the current temperature for the drying cycle. In the TIMED mode

only, the temperature can be changed by pressing and holding the DRYING

TEMPERATURE button and using the “up arrow” or “down arrow” buttons.

DRYING TIME. In AUTO drying mode, pressing and holding this button will

show in the display “-A-”. This indicates that the automatic drying cycle has

been selected. In TIMED mode, pressing and holding this button will show in

the display the current time (in minutes) set for the drying cycle. In the TIMED

mode only, the drying time can be changed by pressing and holding the DRYING

TIME button and using the “up arrow” or “down arrow” buttons.

COOLING TIME. In AUTO cooling mode, pressing and holding this button

will show in the display “-A-”. This indicates that the automatic cooling cycle

has been selected. In TIMED mode, pressing and holding this button will show

in the display the current time (in minutes) set for the cooling cycle. In the

TIMED mode only, the cooling time can be changed by pressing and holding the

COOLING TIME button and using the “up arrow” or “down arrow” buttons.

“UP” AND “DOWN”. These two buttons are used in conjunction with the

DRYING TEMPERATURE, DRYING TIME, and COOLING TIME buttons to

change the value of those parameters. Pressing and releasing the button will

step the value one unit at a time (slowly for the first 5 seconds and then

rapidly). Pressing and holding both buttons will show the actual temperature in

the dryer.

REPEAT LAST CYCLE. Pressing this button before starting the drying cycle

will reset all of the parameters (mode, time and temperature) from the last cycle

run. To start a new cycle, press the REPEAT LAST CYCLE button and then

START.

NON-REVERSING/REVERSING (option). Pressing this button “toggles”

between NON-REVERSING and REVERSING.

Safety Tumble

At the end of the cycle the control goes into the “Safety Tumble” mode. “-S-” will

flash in the display. If the door of the dryer is not opened in 2 minutes or the

control is not turned off, the dryer will start running in cooling for 30 minutes to

prevent wrinkles from being set in the goods.

Inhaltsverzeichnis

Andere Cissell Trockner Handbücher

Cissell

Cissell 50LB PARTS Bedienungsanleitung

Cissell

Cissell MANHD175LB Bedienungsanleitung

Cissell

Cissell HD110 Bedienungsanleitung

Cissell

Cissell L36TD30ME Bedienungsanleitung

Cissell

Cissell L28DPS30G Bedienungsanleitung

Cissell

Cissell MANHD30SL Bedienungsanleitung

Cissell

Cissell L36USS30G Bedienungsanleitung

Cissell

Cissell L50CD42G Bedienungsanleitung

Cissell

Cissell L36USS36G Bedienungsanleitung

Cissell

Cissell C30STG Bedienungsanleitung

Cissell

Cissell HDMAN2110 Bedienungsanleitung

Cissell

Cissell L28US30G Bedienungsanleitung

Cissell

Cissell HD175 Bedienungsanleitung

Cissell

Cissell L36URD36E Bedienungsanleitung

Cissell

Cissell 36BD30 Bedienungsanleitung

Cissell

Cissell 28BS30 Bedienungsanleitung

Cissell

Cissell MANHD30.1 Bedienungsanleitung

Cissell

Cissell 36BS30 Bedienungsanleitung

Cissell

Cissell L44CD42G Bedienungsanleitung

Cissell

Cissell HD150.1 Bedienungsanleitung

Cissell

Cissell L36USS36G Bedienungsanleitung

Cissell

Cissell HD125 Bedienungsanleitung

Cissell

Cissell HD190G Bedienungsanleitung

Cissell

Cissell MANHD190 Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung