Citizen LINE THERMAL PRINTER CT-S280 Bedienungsanleitung

— 1 —

TE74922-02F

1.02E-0916

Printed in Japan

LINE THERMAL PRINTER

MODEL CT-S280

Quick Start Guide

GENERAL PRECAUTIONS

●For further information and more detailed instructions on the use of your new

printer, please refer to the complete user manual included on the CD-ROM

accompanying your printer.

●Please take moment to read this Quick Start Guide which will familiarise yourself

with the printer and its operation.

●The information contained herein is subject to change without prior notice.

●Reproduction or transfer of part or all of this document in any means is prohibited

without permission from CITIZEN SYSTEMS.

●Note that CITIZEN SYSTEMS is not responsible for any operation results regardless

of missing, error, or misprinting in this manual.

●Note that CITIZEN SYSTEMS is not responsible for any trouble caused as a result

of using options or consumables that are not specified in this manual.

●Except explained elsewhere in this manual, do not attempt to service, disassemble,

or repair this product.

●Note that CITIZEN SYSTEMS is not responsible for any damage attributable to

incorrect operation/handling or improper operating environments that are not

specified in this manual.

●Data are basically for temporary use, not stored for a long period or permanently.

Please note that CITIZEN SYSTEMS is not responsible for damage or lost profit

resulting from the loss of data caused by accidents, repairs, tests or other

occurrence.

●If you find loss of information, error, or uncertain matter, please contact your

CITIZEN SYSTEMS dealer.

●If you find any disordered or missing page(s), contact your CITIZEN SYSTEMS

dealer for replacement.

— 2 —

This printer conforms to the following Standards:

The Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS

Directive 2002/95/EC, and the WEEE Directive 2002/96/EC.

LVD:EN60950-1

EMC : EN55022 Class A

EN61000-3-2

EN61000-3-3

EN55024

This declaration is applied only for 230V model.

Declaration of Conformity

IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy

and if not installed and used in accordance with the instruction manual, may cause

interference to radio communications. It has been tested and found to comply with

the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC

Rules, which are designed to provide reasonable protection against such interference

when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

CAUTION: Use shielded cable for this equipment.

Sicherheitshinweis

Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und

leicht zugänglich sein.

For Uses in Canada

This digital apparatus does not exceed the class A limits for radio noise emissions

from digital apparatus, as set out in the radio interference regulations of the Canadian

department of communications.

Pour L’utilisateurs Canadiens

Cet appareil numérique ne dépasse pas les limites de carégorie a pour les émissions

de bruit radio émanant d’appareils numériques, tel que prévu dans les réglements

sur l’interférence radio du départment Canadien des communications.

EPSON and ESC/POS are registered trademarks of Seiko Epson Corporation.

CITIZEN is a registered trade mark of CITIZEN WATCH CO.

CITIZEN es una marca registrada de CITIZEN WATCH CO.

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

— 3 —

Do not use or store this product in a place where it will be exposed to:

●Flames or moist air

●Direct sunlight

●Hot airflow or radiation from a heating device

●Salty air or corrosive gases

●Ill-ventilated atmosphere

●Chemical reactions in a laboratory

●Airborne oil, steel particles, or dust

●Static electricity or strong magnetic field

•Neglecting these warnings may result in printer failure, overheating,

emission of smoke, fire, or electric shock.

PRECAUTIONS ON PRINTER INSTALLATION

Do not drop any foreign object nor spill liquid into the printer. Do not

place any object on the printer either.

●Do not drop any metallic object such as paper clip, pin or screw into

the printer.

●Do not place a flower vase, pot or cup containing water on the printer.

●Do not spill coffee, soft drinks or any other liquid into the printer.

●Do not spray insecticide or any other chemical liquid over the printer.

•Ametallic foreign object, if accidentally dropped into the printer, may

cause printer failure, fire, or electric shock. Should it occur,

immediately turn the printer off, unplug it from the supply outlet,

and call your local CITIZEN SYSTEMS dealer.

WARNING

Do not handle the printer in the following ways:

●Do not allow the printer to sustain strong impacts or hard jolts (e.g.,

trampling, dropping, striking with a hard edge).

●Never attempt to disassemble or modify the printer.

•Neglecting to handle properly may result in printer failure,

overheating, emission of smoke, fire, or electric shock.

Install, use, or store the printer out of the reach of children.

•Electric appliances could cause an unexpected injury or accident if

they are handled or used improperly.

•Keep the power cord and signal cables out of the reach of children.

Also children should not be allowed to gain access to any internal

part of the printer.

•The plastic bag the printer came in must be disposed of properly or

kept away from children. Wearing it over the head may lead to

suffocation.

— 4 —

PRECAUTIONS IN HANDLINGTHE PRINTER

Please observe the following precautions for power source and power

cord:

●Do not plug or unplug the power cord with a wet hand.

●Use the printer only at the specified supply voltage and frequency.

●Use only the specified AC adapter with the printer.

●Use the power cord supplied with the product. Never use the power cord

for other product.

●Check to make sure that the supply outlet from which the printer is

powered has a sufficient capacity.

●Do not supply the printer from a power strip or current tap shared

with other appliances.

●Do not plug the power cord into a supply outlet with dust or debris

left on its plug.

●Do not use a deformed or damaged power cord.

●Do not move the printer while the printer power is on.

•Neglecting to handle properly may result in printer failure, emission

of smoke, fire, or electric shock.

•An overload may cause the power cord to overheat or fire or the circuit

breaker to trip.

●Do not allow anything to rest on the power cord. Do not place the

printer where the power cord will be trampled on.

●Do not use or carry the printer with its power cord bent, twisted, or

pulled.

●Do not attempt to modify the power cord unnecessarily.

●Do not lay the power cord in the neighbor of a heating device.

•Neglecting these cautions may cause wires or insulation to break,

which could result in leakage, electric shock, or printer failure. If a

power cord sustains damage contact your CITIZEN SYSTEMS dealer.

●Do not leave things around the supply outlet.

●Supply power to the printer from a convenient wall outlet, readily

accessible in an emergency.

•The printer may not be immediately shut down in an emergency.

●Insert the power plug fully into the outlet.

●If the printer is not to be used for a long time, leave it disconnected

from its supply outlet.

●Hold the plug and connector when plugging or unplugging the power

cord or signal cable after turning off the printer and the appliance

connected to it.

WARNING

— 5 —

2 Model Classification

The printer models are classified by the following designation method:

1 Unpacking

When unpacking the printer, confirm that the following are provided:

●Printer: 1

●AC adapter: 1

●AC power cord: 1

●Sample paper roll: 1 roll

●Quick start guide(This guide): 1

●CD-ROM: 1

Printer

AC adapter

Sample paper roll AC power cord

CD-ROM

Quick start guide

* The AC power cord plug will vary depending of the region.

CT-S 280 RS U - WH

Case color

WH: Cool white

BK: Black

Destination (Letters + Power cord)

J: Japan

E: Europe

U: USA

Interface

PA: Parallel IEEE 1284 compliant

RS: Serial RS-232C compliant

UB: USB

Model name

— 6 —

Connecting the AC Adapter and AC Power Cord

CAUTION!

●Use only the specified AC adapter with the printer.

●When disconnecting a cable, do not pull out by the cable. Always hold the plug.

●Always keep the AC power supply away from other noise generating equipment.

●Do not pull the power cord. Otherwise fire, electric shock, or power disconnection

may result.

●If lightning is approaching, unplug the AC power cord from the wall outlet. Otherwise

fire or electric shock may result.

●Keep the power cord away from heat generating appliances. Otherwise the shield of

power cord may be fused resulting in a fire or electric shock.

●If the printer is not to be used for a long time, leave it disconnected from its supply

outlet.

●Lay the cable not to be caught by the leg or the like.

1. Tu rn off the printer power.

2. Plug in the cable connector of the

AC adapter to the power connector

at the rear of the printer.

3. Connect the AC power cord to the

inlet of the printer, and insert the

AC power-cord plug into a suitable

wall outlet.

4 Connecting Interface Cables

Turn off the printer and unplug the power connector. Then follow the procedure for

interface cable connection.

Orient the interface cable terminal correctly and insert it into the interface connector.

CAUTION!

●When disconnecting the cable, always hold the connector.

●Lay the cable not to be caught by the leg or the like.

Serial Interface Parallel Interface USB Interface

AC power cord

Inlet

Cable

connector

AC adapter

— 7 —

5 Setting/Replacing Paper Rolls

WARNING

●When opening the paper cover, take care not to touch the print head or cutter blade.

Otherwise, burning or injury of hand may result.

1. Pull the cover open button fully toward you.

2. Open the paper cover.

3. Insert a paper roll with is print area facing down

as shown in the figure and pull out the paper

end straightforward by several cm out of the

printer.

4. Close the paper cover until a click can be heard.

6 Self-printing

Insert paper into the printer. With the FEED switch pressed and held, turn the printer

power on, keep the FEED switch held for about 1 second, and then release the FEED

switch. The printer starts self-printing. The printer prints model name, version, DIP

switch setting, memory switch setting, and built-in fonts.

Memory

switch

setting

Serial communication

condition (Only serial

interface model)

DIP switch setting

(Only serial interface

model)

Firmware version

Interface

Buffer size

CAUTION!

●Always use the specified types of paper roll.

●Confirm that the paper roll is set correctly.

●When the paper is skewed and not extended straightforward from under the cover,

open the cover and adjust the paper correctly.

●When closing the cover, press on the center part of the cover to close it firmly.

●When setting paper, pay attention not to let your fingers get injured by the edge of

paper.

— 8 —

7 Error Indication

●Paper end

Paper empty is detected in two steps: paper near-end and paper end. It causes the

ERROR LED to light. If paper end is detected, refill the paper. If the paper cover is

open, a paper-end is detected.

●Paper cover open

When the paper cover is opened, Paper cover open is detected and the ERROR LED

goes on.

During printing, do not open the paper cover. If you open the paper cover accidentally,

the ERROR LED blinks. Confirm the paper and close the cover. Printing resumes

automatically.

●Thermal head overheat

When you print dense characters or dark image, the head temperature rises. If the

head temperature exceeds a specified level, the printer stops printing operation and

waits till the head temperature is lowered. During waiting, the ERROR LED blinks.

When the head temperature is lowered, printing resumes automatically.

The status of LED, lighting or blinking, including other errors is shown below.

Status POWER LED ERROR LED

Paper-end Lights Lights

Paper near-end Lights Lights

Cover open error *1 Lights

Cover open error Lights Lights

Head overheat error Lights

Memory check error OFF

Low voltage error Lights

High voltage error Lights

Macro execution Lights

wait *2

*1: When the printer is printing.

*2: The ERROR LED may blink even in the execution of macro function.

— 9 —

LINE THERMAL PRINTER

MODEL CT-S280

Guide de démarrage

rapide

PRÉCAUTIONS GÉNÉRALES

●Pour d’ultérieures instructions et des informations plus amples et détaillées sur

l’utilisation de votre nouvelle imprimante, référez-vous au manuel d’utilisateur

complet compris dans le CD-ROM accompagnant l’imprimante.

●Veuillez lire ce Guide de Début Rapide pour vous familiariser avec l’imprimante et

son fonctionnement.

●Les informations contenues dans ce manuel sont sujettes à des changements

sans préavis.

●La reproduction ou le transfert d’une partie ou de tout ce document par n’importe

quel moyen est interdite sans l’autorisation de CITIZEN SYSTEMS.

●Prière de prendre note que CITIZEN SYSTEMS n’est pas responsable de tout

résultat de fonctionnement indépendamment de manque, d’erreur ou de défaut

d’impression de ce manuel.

●CITIZEN SYSTEMS n’est pas responsable d’aucun problème causé par l’utilisation

des options ou produits consommables qui ne sont pas indiqués dans ce manuel.

●Sauf en cas de spécification contraire dans ce manuel, ne pas essayer d’entretenir,

démonter ou réparer cet appareil.

●Noter que CITIZEN SYSTEMS n’est pas responsable d’aucun dommage attribuable

à une opération/manipulation incorrecte ou à un environnement inexact

d’opération qui ne sont pas indiqués dedans ce manuel.

●Les données sont prévues fondamentalement pour un usage provisoire, et ne

sont pas stockées pendant une longue période ou de manière permanente.

Veuillez noter que CITIZEN SYSTEMS n’est pas responsable des dommages ou

de toute manque de bénéfice résultant de la perte de données provoquées par

des accidents, réparations, essais ou toute autre occurrence.

●Si vous observez une perte d’informations, des erreurs ou des faits douteux,

veuillez contacter votre fournisseur CITIZEN SYSTEMS.

●Si vous trouvez n’importe quelle page désordonnée ou manquante, veuillez

contacter votre fournisseur CITIZEN SYSTEMS pour effectuer le remplacement.

— 10 —