Citizen Eco-Drive 0855 Betriebsanleitung

Setting Instructions for Movement Caliber 0855

Contents (click on a topic)

1) Outline

2) Specifications

3) Before Using

4) Special Functions of the Solar Powered Watch

5) Notes on Use

6) Notes on Recharging

7) Time Required for Recharging

8) Using Your Watch

a. Changing the mode

b. Setting the Time

c. Using the Alarm

d. Using the Chronograph

e. Insufficient Charge and Time Setting Warnings

f. Checking and Adjusting the ‘0’ Position for the Hands

9) Care of Your Timepiece

1. Outline

This is a multi-hand, multi-function analog solar powered watch with an alarm

and chronograph functions. A solar power function as its base, which provides

the power source for the watch hands movement and alarm sound by converting

solar energy into electrical power with the solar cell, fitted on its face.

2. Specifications

Movement Caliber 0855

Accuracy Within +/- 20 seconds per month (when worn at

normal temperatures of 5oC to 41 oC/(41oF to 95 oF)

Operating temperature range Watch operating temperature range : -10oC +60oC

(14oF to 140oF)

Display

Function

• Time Hour, Minute, Second and 24 hour

hands

• Calendar Date, Day of Week

• Alarm Hour, Minute and 24 hour hands.

alarm on/off

• Chronograph Minute, Second, 1/20 (0.05)

second hands

Additional Functions

• Alarm

Daily alarm (sounds for about 15 seconds)

Alarm Monitor (sounds for about 5 seconds)

• Chronograph

Measurement is taken in 1/20 seconds and 60

minutes maximum. (A beep for

start/stop/split confirmation will sound

when the associated button is pressed)

• Insufficient charging warning function

• Stop warning function

• Hands Setting warning function

• Overcharging prevention function

Continuous running times

Fully charged to stopped: Approximately 80 days

Running time when second hand first points to

“CHARGE” position: Roughly 5 days

Battery

Eco Drive rechargeable Manganese Titanium

battery. Not user replaceable

Returnto Table of Contents

3. BEFORE USING

When the watch does not operate according to the handling instruction, it is

insufficiently charged. Charge the secondary battery of the watch for more than 6

hours, approximately 20 cm away from the fluorescent lamp or incandescent lamp as

light sources.

When charging the secondary battery, do not pull it too close to the light source.

* When charging the watch under direct rays of the sun, charge more than an hour.

An Eco Drive Rechargeable battery is used in this watch to store electrical energy.

This rechargeable battery is a clean energy battery which doesn't use any toxic

substances such as mercury. Once fully charged, the watch will continue to run for

about 80 days (using the alarm sound for, 15 seconds/day and the chronograph

measurement 60 minutes/day) without further charging

How to use this watch properly

For the comfortable use of this watch and its additional alarm and chronograph

functions, take care to keep it sufficiently recharged.

There is no concern for over-charging this watch. (Over-Charging Prevention

Functions is included) We recommend that you recharge the watch everyday.

4. SPECIAL FUNCTIONS OF THE SOLAR POWER WATCH

If this watch becomes insufficiently charged, a warning function comes into

operation and the display changes, as below.

Returnto Table of Contents

Insufficient Recharging Warning Function (Refer to section "Insufficient

Charge and Time Setting Warnings")

If the watch is put in the undercharged state during any display mode, it

switches to the time display when in other display modes, then the second hand

moves to the A CHARGE position, indicating the shortage of electricity.

(Electric power shortage warning display) Even then, the time (hour, minute and

24-hour hands) runs accurately.

• The alarm does not ring even if it is set.

• If the chronograph is being used, measurement stops and it is reset.

• The push button does not function.

Stop Warning Function (Refer to section "Insufficient Charge and Time

Setting Warnings")

If the watch is left intact in the undercharged state, about 5 days later the second

hand will move to the A STOP position, indicating that the watch has stopped due to

Electric power shortage. (Stop warning display) The other hands (hour, minute and 24-

hour hands) also stop.

* In this condition, all function stop.

Hands Setting Warning Function (Refer to section "Insufficient Charge and

Time Setting Warnings")

When the watch is recharged by exposing it to light after once stopped, the second hand

moves to the ^SET position, indicating that the watch does not keep correct time.

(Hands setting warning display)

* The hours, minute and 24-hour hands run at the incorrect time.

Over-Charging Prevention Function

You can recharge without worry. When the rechargeable battery is fully

recharged, the over-charging prevention function works so that the rechargeable

battery is not overcharged.

5. NOTES ON USE

/!\ Warning

Never use a battery other than the Eco Drive Rechargeable battery.

The watch structure is so designed that a different kind of battery

other than the specified cannot be used to operate it. However, in

case a different kind of battery such as a silver oxide battery, there is a

danger that the watch will be overcharged to burst, causing damage to the

watch and even to the human body.

Returnto Table of Contents

6. NOTES ON RECHARGE

/!\ Caution

* The watch will be damaged during recharging if it gets too hot (Over

60'C/140'F).

Avoid recharging at high temperatures (Over 60oC/140oF).

(eg)Charging the watch near a light source that easily become hot, such as

an incandescent lamp or a halogen lamp.

Charging in a place that easily becomes hot, such as a dashboard.

7. TIME REQUIRED FOR RECHARGE

Time required for recharge may vary according to the design (color of the

dial, etc.) and operating environment. The following table will serve you as

rough reference.

* The recharging time is the time when the watch is continuously exposed to

light.

Running Time

At Full Charge Low Charge

Warning

Quick

Start Feature

80 Days 5 Days No

Charge Rates from Indoor Light Source

Indoors, Office

(500 lux) Fluorescent at 6" Distance

Incandescent at 20" Distance

(3000 lux)

One Day

Use One

Second

Step

Full

Charge One Day

Use One Second

Step Full

Charge

2.5 Hours 28 Hours 220

Hours 25 Minutes 4.5 Hours 34 Hours

Charge Rates from Outdoor Light Source

Outdoors Cloudy

(10,000 lux) Outdoors Bright Sun

(100,000 lux)

One Day

Use One

Second

Step

Full

Charge One Day

Use One Second

Step Full

Charge

5 Minutes 30

Minutes 9 Hours 2 Minutes 10 Minutes 3.5 Hours

Returnto Table of Contents

8. HOW TO USE THIS WATCH

1) CHANGING THE MODE

Other than the time display, this watch has alarm and chronograph main

display functions- Each press of the (M) button changes Time <TME> ->

Alarm <ALM> -> Chronograph <CHR> -> "O" position confirmation <(O)>.

Confirm the change with the mode hand.

After that returns to the time mode <TME> display.

Display alarm set time. The alarm

setting is in

1 minute. Confirm of am/pm with

the 24-hour hand If the alarm is

ON, it will ring at the set time

for 15 seconds once every day.

Display present time in hours,

minutes, seconds and 24-hours.

Use the 24-hour hand to confirm

am/pm

Measures up to a maximum

60 minutes in 1/20

seconds, and display split

times.

A confirmation sounds when

you start/stop or measure

a split time

Not used usually. This

display function should be

used to adjust the display

correctly, in case a wrong

display of

time results from static

electricity, shock etc

Returnto Table of Contents

2) TIME SETTING Check that the mode hand is indicating <TME>

and the watch is in time mode.

1) Pull the button (M) out, so that the

second hand stops at the "O" position.

Time setting synchronize the minute hand -

> hour hand -> 24-hour hand

When the watch is adjusted by button

operation, the time setting is completed

by electro-magnetic correction.

2) Set the time by pressing button (B) or button (C)

Each time button (B) is pressed ...............

The watch advances 1 minute in a clockwise direction.

Each time button (C) is pressed ...............

The watch turns back 1 minute in a counter-clockwise direction.

Depress button (B) or (C) continuously, the hands move rapidly. Turn the hands

in the direction that is closest to set the time.

3) After setting the time, push the button k to the normal position and

the watch will start at the correct time.

If the minute hand shows incorrect position

a. Pull button (M) out to the first click.

b. When button (B) or (C) is pressed with button (A) depressed, the minute

hand moves every 20 seconds.

Caution: Do not press three buttons (A), (B) and (C) simultaneously. If

all the buttons are pressed simultaneously, "O" Position Adjustment

(page 10) and all other functions will need to be set again.

3) USING THE ALARM

The alarm sounds once a day for 15 seconds at the alarm time set. Pressing

any of buttons (A), (B) or (C) stops the alarm ringing.

Setting the alarm

Alarm setting is on a 24-hour system

in 1 minute. The hands are moved

thus: minute hand -> hour hand -> 24-

hour hand.

1)Press button (M) to set the mode

hand to <ALM> and switch to the

alarm mode.

2)Pull button (M) out to the alarm

set time adjusting state.

3)Press buttons (B)or (C) to set the

minute, hour and 24-hour hands to

the desired time.

• Each time button (B) is pressed … The watch advances 1 minute in a

clockwise direction

• Each time button (P is pressed … The watch turns back in 1 minute

increments in a counter clockwise direction

Returnto Table of Contents

Depress button (B) or (C) continuously, the hands move rapidly.

After setting the alarm time, push the (M) button. The hour, minute and 24-

hour hands move rapidly automatically to the present time. If those hands do

not stop moving, push the (M) button again.

Switching the alarm ON and OFF

Each time button (A) is pressed in the alarm mode, the alarm switches ON and OFF

Alarm sound monitor

On the alarm mode (button (M) in the normal position), press button (A) and the

alarm will sound for 5 seconds.

Note

* There may be some variation in the volume of the alarm sound, depending on

how much the Eco Drive Rechargeable battery is charged.

* The alarm sound volume gets rather lower in the display other than the time

display (alarm, chronograph, "O" position confirmation, and each display's

adjustment state).

Once the alarm time has been set, use the watch normally in time display mode.

4) USING THE CHRONOGRAPH

Chronograph measurement is taken in 1/20 (0.05) seconds and can continue

for 60 minutes max. Over 60 minutes, the watch enters the chronograph-

reset state.

Chronograph measurement

Chronograph reset

Read the chronograph hands

For measurement less than 1 minute

Second hand -> Chronograph second hand Function hand -> Chronograph 1/20

second hand

For measurement over 1, minute:

Second hand -> Chronograph second hand Function hand -> Chronograph

minute hand

Returnto Table of Contents

Chronograph measurement

Chronograph standard or accumulated elapsed

time measurement.

1) Press button (M) to set the mode hand <CHR>

and get the chronograph display. At this

time, the second hand and the function hand

will return to the "O" position.

The hour, minute, and 24-hour hands

show the present time.

2) Each time button (A) is pressed, it

repeatedly starts or stop the chronograph,

along with a confirmation sound.

How to read each chronograph hand if the

measured time when the chronograph is stopped

is over 1 minute.

a. Read the number of minutes with the function

hand.

b. Read the number of seconds with the

second hand.

c. While pressing button (B) continuously, the

function hand switches to 1/20 (0.05) second

hand measurement, so read the value at that

time.

When button (B) is released, the function

hand resumes showing chronograph minutes.

3) While the chronograph is stopped state,

pressing button & reset the function hand and

the second hand to the "O" position.

Chronograph split measurement

Pressing button (C) during chronograph

measurement causes the chronograph split time

to appear on display with a beep for

confirmation.

Press button (C) again, the next chronograph

split time is displayed, along with a

confirmation sound. The split time display

is automatically cancelled after about 10

second, and the chronograph return to the

measurement state.

During either chronograph split time display

or measurement, pressing button (A) causes

the chronograph stop to appear on display.

In the chronograph stop state, pressing

button (C) causes the chronograph reset.

During split time measurement or while

split time display, each time you press

button (C) the next split time is

displayed.

Returnto Table of Contents

5) TIME SETTING AND RECHARGE WARNINGS

When shown the insufficient charge warning display

If the watch is put in the undercharged

state during any display mode, it

switches to the time display when in

other display modes, then the second

hand modes to the ^CHARGE position,

indicating insufficiently charged. In

such a case, expose the watch to

sufficient light for the warning state

to be cancelled. (The second hand

return to 1 second movement)

It takes about 30 minutes from starting

to expose the watch to light until this

warning state is cancelled. The

charging time varies depending on the

light (light source) that radiates over

the watch.

When shown the stop warning display If the watch is left intact in the

undercharged state, about 5 days later

the second hand move to the ^STOP

position, indicating that the watch has

stopped due to insufficient recharge.

* All function are stopped in this state.

In such a case, expose the watch to

sufficient light for the warning state to

be cancelled.

After carrying out sufficient

charging, it is necessary to reset

the alarm time.

When shown the hands setting warning display

If you expose a watch which has stopped

once to light and recharge it, the second

hand will move to the ^SET position to let

you know that the time is incorrect.

In such a case, readjust the hour, minute

and 24- hour hands to keep correct time.

Without adjusting the time hands after the

watch is fully recharged, you cannot use

such function as alarm, chronograph, etc.

properly.

Be careful because if the watch is not

sufficiently charged during the Hands

Setting Warning Display State, and if

light is blocked from it, the second hand

will change to the ^STOP position and the

watch will stop running.

Returnto Table of Contents

Inhaltsverzeichnis

Andere Citizen Betrachten Handbücher

Citizen

Citizen Japon JP25 Momentus CC287 Bedienungsanleitung

Citizen

Citizen MOVEMENT CAL GP00 Bedienungsanleitung

Citizen

Citizen 1400A-02 Handbuch

Citizen

Citizen E030 Handbuch

Citizen

Citizen Eco-Drive B612 Bedienungsanleitung

Citizen

Citizen 6S00 Bedienungsanleitung

Citizen

Citizen Peyten Bedienungsanleitung

Citizen

Citizen 6702 Bedienungsanleitung

Citizen

Citizen CTZ-B6810 Bedienungsanleitung

Citizen

Citizen J810 Bedienungsanleitung

Citizen

Citizen Eco-Drive CTZ-B8143 Bedienungsanleitung

Citizen

Citizen Watch Bedienungsanleitung

Citizen

Citizen H144 Bedienungsanleitung

Citizen

Citizen P991 Handbuch

Citizen

Citizen Elysee 82S5 Bedienungsanleitung

Citizen

Citizen 0S22 Bedienungsanleitung

Citizen

Citizen ANA-DIGI 30-7XXX Bedienungsanleitung

Citizen

Citizen Eco-Drive CAL 8651 Bedienungsanleitung

Citizen

Citizen Sport AW1524-84E Bedienungsanleitung

Citizen

Citizen Quartz 0580 Handbuch

Citizen

Citizen Quartz E870 Handbuch

Citizen

Citizen CAL.0S Series Bedienungsanleitung

Citizen

Citizen CTZ-B6778 Bedienungsanleitung

Citizen

Citizen YACHTING JH2 series Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

Seiko

Seiko N830 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung