Citronic CV8A Bedienungsanleitung
CV SERIES
Active Speaker Cabinets
Item ref: 178.154UK, 178.157UK,
178.160UK, 178.163UK
User Manual
CV series Active Speaker User Manual
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Introduction
Thank you for choosing this CV series active cabinet. This cabinet combines a powerful digital
amplifier section with a high density moulded enclosure for high output and efficient
performance. Please read this manual prior to use to avoid damage through misuse.
Package Contents
Please check the contents to ensure that the product has been received in good condition.
CV active speaker
IEC mains power lead(s)
If you find any accessory is missing or the product has arrived with any problems, please
contact your retailer at once. This product contains no user-serviceable parts so make no
attempt to try to fix or modify this item yourself as this will invalidate the warranty. We
recommend you keep the original package and proof of purchase for any possible replacement
or returned demand.
Warning
To prevent the risk of fire or electric shock, do not expose this appliance to rain or moisture
and avoid ingress of water into the enclosure. To prevent electric shock do not remove the
cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety
Prior to connecting mains, ensure that the supply voltage is correct and the mains lead is in
good condition. If the mains fuse blows, refer the unit to qualified service personnel
Placement
Keep the unit out of direct sunlight and away from heat sources.
Place the unit in an upright position during use and storage.
Keep the unit away from moisture or dusty environments.
Cleaning
Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls.
To avoid damage, do not use solvents to clean this equipment.
CV series Active Speaker User Manual
Rear Panel
Operation
Connect the CV-series active speaker unit to the mains using the appropriate mains IEC lead
supplied.
Combined 6.3mm jack or XLR (balanced or unbalanced) inputs are provided to connect either
a microphone, line input or both. Tone shaping is available by adjusting the BASS and TREBLE
controls and each input is governed by a VOLUME rotary control.
An XLR LINK output is provided from each input channel to link onto further active speakers.
Connect the required inputs and outputs and with the VOLUME controls down (anti-clockwise),
turn the POWER switch on. BASS and TREBLE controls should remain pointing vertically (12-o-
clock position). Gradually increase the volume and check that the signal is present by seeing
the SIGNAL/CLIP indicator light up green and that the sound is being delivered from the
speaker. Increase VOLUME to the required level.
When the signal level is too high, the SIGNAL/CLIP indicator will light red and the output may
sound distorted. In this eventuality, reduce the VOLUME to the point where the indicator only
lights red very briefly on the loudest peaks of the input signal(s).
Ensure that volume controls are turned down before powering down and unplug from the
mains when not in use for long periods.
1. MIC input (XLR or jack)
2. LINE input (XLR or jack)
3. LINK outputs (XLR)
4. BASS EQ controls
5. TREBLE EQ controls
6. VOLUME controls
7. SIGNAL/CLIP indicators
CV series Active Speaker User Manual
Specifications
Model
CV8A
CV10A
CV12A
CV15A
Power supply
110-240Vac, 50/60Hz (IEC)
Flying Points
2 x M8 + 2 x rear hook points
LF driver
200mm (8“)
250mm (10“)
300mm (12“)
380mm (15“)
LF driver: Coil size
35mmØ
50mmØ
65mmØ
75mmØ
HF driver
38mmØ Ti
38mmØ Ti
62mmØ Ti
62mmØ Ti
HF driver: Coil size
25mmØ
25mmØ
44mmØ
44mmØ
Power rating: RMS
75W
150W
300W
400W
Power rating: Max
150W
300W
600W
800W
Crossover frequency
3.5kHz
3.5kHz
3.0kHz
2.5kHz
Frequency response
60Hz-20kHz
55Hz-20kHz
45Hz-20kHz
40Hz-20kHz
SPL @ 1W/1m
97dB
99dB
101dB
103dB
Max SPL
121dB
125dB
127dB
129dB
THD
0.10%
SNR
87dB
Dimensions (mm)
415 x 285 x 265
505 x 335 x 310
610 x 390 x 350
735 x 475 x 420
Weight (kg)
10.5
14.5
18.5
23.5
Troubleshooting
No output and no LEDs lit
Check POWER switch is on
Check mains lead is connected
Check mains fuse hasn’t blown
Power LED lit but no sound
from external inputs
Check leads are OK and connected properly
Check volume and on/off switch on external mic or line source
Check VOLUME control is not fully down
Distorted or overdriven
output
Ensure that a line level signal is not connected to MIC input
Reduce the VOLUME until the SIGNAL/CLIP indicator is lit green
Reduce BASS and TREBLE controls if set high
Output is too low
Ensure that a microphone is not connected via the LINE input
If SIGNAL/CLIP indicator is not showing red, increase VOLUME
IF BASS and TREBLE controls are set low, increase both controls
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2013. AVSL Group Ltd.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Citronic Sprecher Handbücher
Citronic
Citronic ULTIMA CX-LIVE Series Bedienungsanleitung
Citronic
Citronic CUBA Series Bedienungsanleitung
Citronic
Citronic CASA-8A Bedienungsanleitung
Citronic
Citronic CS-6004 Bedienungsanleitung
Citronic
Citronic 170.341 Bedienungsanleitung
Citronic
Citronic CX-2008 Bedienungsanleitung
Citronic
Citronic CT ACTIVE Bedienungsanleitung
Citronic
Citronic ST5 Bedienungsanleitung
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung