clare ClareVision Bedienungsanleitung
ClareVision Video
Surveillance
ClareVision Smart Video Doorbell
Quick Start Guide
11
WHAT’S IN THE BOX
Screwdriver X1Power Kit X1
Power Kit Wires X1 U-shaped Wires X2
Doorbell X1
Faceplate X3
Pick the faceplate
that matches best
for your installation.
Mounting Plate X3
Use a wall stando or
angled plate for
adjusting the viewing
angle.
Plate Foam X1
Use the foam plate to
stabilize the Video
Doorbell when installed
on an uneven surface.
TOOLS YOU MAY NEED
Drill Pencil
Wire Connectors (x4) Mounting Screws (x3) Anchors (x3)
Security Screw (x1) Wire Terminal Screws (x2)
12
• Install the Power Kit if using a mechanical or digital chime.
• If no chime is installed, skip the Power Kit installation.
• The Video Doorbell requires 12VAC to 30VAC power.
NOTE
Not included in the package.
POWER KIT INSTALLATION
Shut o the electricity at the
breaker that controls the
doorbell’s circuit.
1
Remove the cover from your
mechanical chime.
3
Insert one end of the wire
harness into the power kit.
2
Remove the existing chime wires
from the terminals
named TRANS and FRONT.
4
REAR
TRANS
FRONT
REAR
TRANS
FRONT
3
Connect the wire harness to the
chime’s terminals
named TRANS and FRONT.
5
Mount the power kit to the side
of the chime.
7Replace the chime cover.
8
Insert the existing chime wire and
the other end of the wire harness
into the wire connector, and twist it
tightly. Repeat this step with the
other chime wire.
6
REAR
TRANS
FRONT
Wire
Connectors
Chime Wire Wire Harness
4
(Optional) If the wall is uneven,
attach the plate foam to the
mounting plate.
2
Shut o the electricity at the
breaker that controls the
doorbell’s circuit.
1
Wiring Overview
Doorbell Installation
REAR
TRANS
FRONT
REAR
TRANS
FRONT
• Recommended Installation Height: 4ft (1.2m) above the ground.
NOTE
5
reset
NOTE
• Recommended Hole Depth: 1-1.5in (25-30mm).
Mark the drill points with a
pencil.
3
Ax the mounting plate to the
wall.
5Remove the faceplate cover.
6
Drill holes according to the drill
points, and insert anchors.
4
Anchor
Mounting Screw
6
7
U-Shaped Wire
Wire Terminal
Screws
Power Supply: 12 to 30 VAC
Using wire nuts connect U-shaped wires to existing doorbell wires, then
connect U-connectors to doorbell using Wire Terminal Screws.
8
Insert the mounting pegs on the back of the Video Doorbell into the
mounting plate and slide down.
9
• The Video Doorbell is powered on when the LED indicator ring around the
call button is illuminated. If not, make sure your electricity is o and check
the wiring. Once you have a solid LED indicator around the ring button,
proceed to doorbell setup.
NOTE
Insert and fasten Security Screw to lock doorbell to mounting plate.
10
Restore the electricity at the breaker.
11
8
Doorbell Setup
9
ClareVision App
Google Play Store
ClareVision App
Apple App Store
Press and hold the reset button until you hear the second voice prompt,
“Doorbell has been reset and will reboot”, approximately 10 seconds.
1
Reset Button
Wait until the LED light ashes blue, indicating the reset is complete. You
will hear the voice prompt say, “The doorbell is ready to connect to WiFi.”
2
Download and install the ClareVision app from the google Play or Apple
App store to your device.
3
Andere Handbücher für ClareVision
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
