Clare ClareOne CLR-C1-PNL1 Bedienungsanleitung

ClareOne Wireless Security and Smart Home Panel Quick Start Guide

Model CLR-C1-PNL1



Press the backplate gently

back in place.

P 

Remove the backplate,

exposing the battery.

Attach the power supply. Verify

that the battery is plugged in.

D

W

Connect the panel stand,

and then slide to the desired

position.

Remove the backplate,

exposing the battery.

Attach the power

supply to the panel.

Place the

mounting

bracket

against the

wall, and then

use the in-

cluded screws

to attach the

mount to the

wall.

Press the panel onto the mounting

bracket, and then slide the panel

downward.

P

Connect power

supply with brack-

et to the wall.

Do not connect to a

receptacle controlled

by a switch.

W

Follow the displayed onscreen wizard.

O - I A

Use the Clare Controls Install Assist

app to add smart home devices.

E

Rest secure with ClareOne

and enjoy the benets of a

safe, smart, and happy home

with Clare Contols.

T S-

Clare Controls, LLC.

General: 941.328.3991

Fax: 941.870.9646

www.clarecontrols.com

Integrator/Dealer Support:

941.404.1072

claresupport@clarecontrols.com

Note: For additionanl

power options, refer to

the full manual

DOC 1871.

D M N

• e panel must be

mounted at least 1

from a table edge, a

heat or water source,

and any sources of

interference.

• Peel the clear lm from

the anti-skid rubber on the

bottom of the panel mount.

If this lm is not removed,

the panel may slide on a

tabletop.

To view the full

manual DOC 1871,

scan the QR code or

access the link below.

http://bit.ly/35RJzMd

Before starting installation see standards on residential installation, refer to Installation of Residential Fire Warning Systems,

CAN/ULC-S540. e system must be installed in accordance with Chapter 29 of the National Fire Alarm and Signaling Code,

ANSI/NFPA 72.

Homeowners should contact their dealer for assistance.

ClareOne Wireless Security and Smart Home Panel Quick Start Guide

Model CLR-C1-PNL1

R

ETL listed to UL 1023, UL 985, UL 1610, ULC C1023, ULC S545, ULC S304

is device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) is device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

is equipment should be installed in accordance with Chapter 29 of the National Fire Alarm and Signaling Code, ANSI/NFPA 72, (National Fire Protection Association, Batterymarch

Park, Quincy, MA 02269).

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Note: is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. ese limits are designed to provide

reasonable protection against harmful interference in a residential installation. is equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

is equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. is equipment should be installed and operated with minimum distance 20cm

between the radiator and your body.

W D

(1) Power supply to connect to a non-switch

controlled outlet.

(2) (Optional) Ethernet cable to connect to router.

(3) (Optional) Wires to connect an external siren.

Use recognized energy limited cable for connection.

Battery notes:

• For battery replacement order CLR-C1-BATT

• Maximum Battery Voltage: 4.35V DC

• Maximum Battery Capacity: 5200mAh

• Maximum Charging Current: 2600mA