Clarion NZ502E Bedienungsanleitung

29NZ502E

English

INSTALLATION / WIRE

CONNECTION GUIDE

Before Starting

1. This set is exclusively for use in cars with a negative ground

12 V power supply.

2. Read these instructions carefully.

3. Besure to disconnect the battery “-” terminal before starting.

This is to prevent short circuits during installation. (Figure 1)

Package Contents

Main unit................................................... 1

Wiring harness.......................................... 1

GPS antenna ............................................ 1

Clamp for GPS antenna's cable............... 3

Double face tape for GPS Antenna .......... 1

Remote control unit.................................. 1

Battery (CR2025) ...................................... 1

(Installed in remote control)

Trim ring ................................................... 1

Cleaning cloth........................................... 1

Warranty Card .......................................... 1

Owner’s manual (CD-R) ........................... 1

Quick Start Guide and

Installation manual.....................................1

Electro tap ................................................ 2

Mounting Bracket key ............................. 2

Flush mount bolts .................................... 4

Hexagon Head Screw .............................. 5

AV cable

Rear radio stud and stopper ....................1

................................................... 1

Figure 1

Car battery

CMY

NZ502E_quick start guide_7-8121-2001-00-01_0807 29.pdf 1 2012-8-7 15:57:57

30 NZ502E

English

General Cautions

1. Do not open the case. There are no user- serviceable

parts inside. If you drop anything into the unit during

installation, consult your dealer or an authorized

Clarion service center.

2. Use a soft, dry cloth to clean the case. Never use

aroughcloth,thinner,benzine,oralcoholetc.For

tough dirt, apply a little cold or warm water to a soft

cloth and wipe off the dirt gently.

Cautions on Installation

1.Prepareallarticlesnecessaryforinstallingthe

source unit before starting.

2. This model features an operation panel that slides

forward.

On some types of cars, the operation panel may

make contact with the dashboard or gearshift

lever, in which cause it cannot be installed. Before

installing, check that the unit will not hamper

operation of the gearshift lever or obstruct your view

beforeselectingtheinstallationlocation.(Figure2)

3. Install the unit within 30° of the horizontal plane.

(Figure3)

4. If you have to do any work on the car body, such as

drilling holes, consult your car dealer beforehand.

5. Use the enclosed screws for installation. Using

otherscrewscancausedamage.(Figure4)

NZ502E

Figure3

NZ502E

Figure2

Gearshiftlever

(Checkthatitdoesnot

touchtheLCD)

Dashboard

Gearshiftlever

Figure4

Chassis Chassis

Damage

Max.8mm(M5screw)

NZ502E_quick start guide_120718.indd 30 2012-7-18 13:48:50

31NZ502E

English

Universal Mount

1. Place the universal mounting bracket into the

instrument panel, use a screwdriver to bend

each stopper of the universal mounting

bracketinward, then secure the stopper as

showninFigure 6.

2. Insert the main unit into the universal

mounting bracket until it locks.

3. Mount the outer escutcheon so that all the

hooks are locked.

Note:

•Some carmodelsrequire specialmountingkitsfor

proper installation.Consult your Clariondealerfor

details.

•Fasten thefront stoppersecurely to prevent the

main unit from comingloose.

•Console opening dimensions

Hole

7-3/16" (182 mm)

2-1/16"(53 mm)

Hole

Hexagonal

bolt

Instrument panel

Stoppers

Screwdriver

Universal mounting bracket

Stoppers

2-Spring

Main Unit

Outer escutcheon

Note:

Set theouter escutcheon

so that itsmetallicparton

thebacksidefitsthe upper

edge of themainunit.

Figure 5

Installing The Main Unit

NZ502E_quick start guide_120718.indd 31 2012-7-18 13:48:51

32 NZ502E

English

Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)

This unit is designed for fixed installation in the

dashboard.

If the vehicle is equipped with a factory-installed

radio, install the main unit with the parts and

screws marked (*2). (Figure 7)

If the vehicle is not equipped with a factory-

installed radio, obtain an installation kit to install

the main unit in the following procedure.

1. Remove the screws from both side of the

main unit. Then, at either side, lift the leaf

spring until the engaging claws are released

from the holes, and slide the spring to the

direction of arrow to remove it. Repeat the

same for the other side to remove the springs

from the both sides. (Figure 6)

2. Secure the mounting brackets to the chassis

as shown in Figure 8. Holes are pre-tapped

for TOYOTA and NISSAN vehicles;

modification,such as drillingnewholes,ofthe

mounting brackets may be required for other

models.

3. Secure the unit in the dashboard, and then

reassemble the dashboard and the center

panel.

Note:

*1The parts and screws with this mark are used to install radio or included in the installation kit.

*2The screws with this mark are enclosed in this set.

*3In some cases, the center panel may require some modification (trimming, filling, etc.).

*4If thehook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool.

MainUnit 2-ScrewEngaging claw

2-Spring

ScrewdriverFigure 6

Mounting bracket *1

(1pairfortheleftandright

sides)

4-Hexagonal screw *2

(M5 ×8)

Center Panel *3

Pocket

Figure 7

MainUnit

NZ502E_quick start guide_120718.indd 32 2012-7-18 13:48:51

33NZ502E

English

Cautions on Wiring

1. Be sure to turn the power off before wiring.

2. Be particularly careful where you route the wires.

 Keepthemwellawayfromtheengine,andexhaustpipe,etc.Heatmaydamagethewires.

3. If the fuse should blow, check to see if the wiring is correct.

 Ifafuseisblown,replaceitwithanewoneofthesameamperageratingastheoriginal(15AFUSE).

4.Toreplacethefuse,removetheoldfuseonthebackoftheunitandinsertthenewone.(Figure8)

NOTE:

There are various types of fuse holder. Do not let the battery side touch other metal parts.

Figure8

Fuse(15AFUSE)

After the connection, ﬁx the cord by a clamp

or insulation tape for protection.

Fuseholder

CAUTION

NZ502E_quick start guide_120718.indd 33 2012-7-18 13:48:51

34 NZ502E

English

Installtion Guide

Installationsguide

NZ502E_quick start guide_120718.indd 34 2012-7-18 13:48:52

WARNING

• Do not install the GPS antenna in a place where it may interfere with the operation of the

airbag or hinder the driver’s visual range.

• Do not use the navigation system with the GPS antenna cord cut off. The power cables in the

cord may be short-circuited.

Note:

• ThesuppliedGPSantennaisforinstallinginsidethevehicle.Donotinstallitoutsidethe

vehicle.

• InstalltheGPSantennamorethan50cmawayfromthemainunit,otheraudiodevicessuch

asCDplayer,andaradardetector.Ifitisinstallednearthesedevices,GPSreceptionmaybe

impaired.

• To improvetheGPSsignalreception,installtheGPSantennahorizontallyonaflatplane.

• DonotwaxorpaintthecoveroftheGPSantenna.Thismayreducetheperformanceofthe

GPSantenna.

• InstalltheGPSantennaatleast10cmawayfromthewindshield.

• WipeoffthedirtofthemountingsurfacebeforeinstallingtheGPSantenna.

GPS antenna

• Mount the GPS antenna.

Stick it surely on a at plane of

the passengerside dashboard

where GPS signal interruption is

minimized.

• Wire the GPS antenna cord.

Fasten the cord using the cord

holders.

Cord holder

Double-sided tape

Bottom face of the GPS antenna

• Stick the double-sided tape to the bottom

face of the GPS antenna.

35NZ502E

English

Wire Connections

Note:

•Beforeinstalling,besuretodisconnectthenegativecableofthecarbattery.

•Intheoptionaldevices,theRCAcablesandtheConnectorcablesareseparately-solditems.

Black

Radio Antenna Jack

4-Channel Amplifier

Subwoofer 1

Subwoofer 2

Line Out

Rear R

Line Out

Rear L

Line Out

Front R

Line Out

Video Out

Front L

Video in

Audio/R

Audio/L

Camera

Yellow

White

Red

White

Yellow

Purple

Gray

Red

Black

White

Steering Wheel

Remote Control Terminal

Yellow

Monitor

Yellow

White

Red

Rear zone out R

Rear zone out L

Red

White

Green

GPS

Antenna

External

Microphone

Connection

iPod/iPhone

MIC

SWI

CAMERA

VISUAL OUT

VISUAL IN

DVB-T Tuner (DTX501E)

DTV

CCA-748 (sold separately)

Rear Vision Camera

Refer to

page 36

NZ502E_quick start guide_120718.indd 35 2012-7-18 13:48:52

36 NZ502E

English

See next page for how to connect the parking brake cord.

15A

A-1

A-2

A-3

A-4

A-5

A-6

A-7

A-8

B-1

B-2

B-3

B-4

B-5

B-6

B-7

B-8

Description

No.

A-1

A-2

A-3

A-4

A-5

A-6

A-7

A-8

B-1

B-2

B-3

B-4

B-5

B-6

B-7

B-8

Rear right-

Rear right+

Rear left-

Rear left+

Front left-

Front left+

Front right+

Front right-

GND

Illumination

Auto antenna

+12V accessory

+12V main power

+12V main power (Yellow)

Auto antenna (Blue)

Phone interrupt (Brown)

Parking (Grass-green)

Remote (Blue/White)

Reverse (Purple/White)

+12V accessory (Red)

No. Description

!!!!Warning!!!!

Parking brake safety

device must be connected

for complete operation

Yellow

Red

Yellow

Red

For VW and Audi: Change wiring as above

Note:

*1: Connecting the PHONE INTERRUPT terminal

The phone interrupt will mute the audio if the lead receives a negative or ground signal.

NZ502E_quick start guide_120718.indd 36 2012-7-18 13:48:52

37NZ502E

English

Connecting the parking brake cord

Connect the cord to parking brake lamp ground in the meter panel.

Note:

•ConnectingtheparkingbrakecordtolampgroundallowsyoutowatchiPod/iPhonevideo/DVDvideo/AVinputwhen

theparkingbrakeisengaged.

•Whentheparkingbrakecordisnotconnected,themonitorwillnotshowanyvideosources.

•If“AUDIOONLY”appearsonthescreenjustafterturningontheACCpowerofthecar,releasetheparkingbrake

whileconrmingsafety,andthenengagetheparkingbrakeagain.

Connecting the accessories

• Connecting to the external amplier

Theexternalamplierscanbeconnectedtothe6channelRCAoutputconnections.Ensurethattheconnectors

are not grounded or shorted to prevent damage to the unit.

• Connecting to iPod/iPhone device

TheiPod/iPhonedevicecanbeconnectedtodedicatediPod/iPhoneconnectiononthemainunit.Fordetailed

information,refertotheinstructionsheetormanualfortheiPod/iPhonecable.

Note:

•ThisunitmaynotsupportallfunctionsofalliPod/iPhonedevices.

•TheiPod/iPhoneconnectionwillchargeyouriPod/iPhoneunlesstheiPod/iPhonebatteryiscompletelydepleted.If

the speciﬁed cord of the cellular phone is connected to the phone interrupt cord of the main unit, the audio mute is

activated when cellular phone in use.

Parkingbrakelamp

cord to battery

Electro-tap

Parkingbrake

signal cord

Parkingbrake

signal cord

Stopper

Parkingbrake

signal cord

Parkingbrake

Parkingbrakecord

(Grass-green)

Parkingbrakecord

(Grass-green)

How to attach the electro-tap

1.PlacetheParkingbrakecordatthestopper,and

fold it back in the direction of the arrow

2.PasstheParkingbrakesignalcordthrough,and

fold it back in the direction of the arrow.

NZ502E_quick start guide_120718.indd 37 2012-7-18 13:48:52

Andere Handbücher für NZ502E

Inhaltsverzeichnis

Andere Clarion Autoempfänger Handbücher

Clarion

Clarion DRX9255EXL Bedienungsanleitung

Clarion

Clarion VRX6570Rz Reparaturanleitung

Clarion

Clarion DB245 Bedienungsanleitung

Clarion

Clarion NX502E Bedienungsanleitung

Clarion

Clarion DRB4375R Bedienungsanleitung

Clarion

Clarion DB568RUSB Bedienungsanleitung

Clarion

Clarion VX404AU Bedienungsanleitung

Clarion

Clarion DXZ265 Bedienungsanleitung

Clarion

Clarion FZ709 Bedienungsanleitung

Clarion

Clarion CZI09 Bedienungsanleitung

Clarion

Clarion CZ509A Bedienungsanleitung

Clarion

Clarion ARX5370R Bedienungsanleitung

Clarion

Clarion DB345MP Bedienungsanleitung

Clarion

Clarion DXZ575USB Bedienungsanleitung

Clarion

Clarion VRX766VD Reparaturanleitung

Clarion

Clarion DBZ45 Bedienungsanleitung

Clarion

Clarion DXZ538R Bedienungsanleitung

Clarion

Clarion MZ55 Bedienungsanleitung

Clarion

Clarion DXZ448R Bedienungsanleitung

Clarion

Clarion VZ401E Bedienungsanleitung

Clarion

Clarion DXZ768RMP Montageanleitung

Clarion

Clarion NX404 Bedienungsanleitung

Clarion

Clarion drb2475 Bedienungsanleitung

Clarion

Clarion DB165 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung