Clarion PU-2294A Bedienungsanleitung

- 1 - PU-2294A/B

PU-2325A

Published by Service Dept.

Printed in Japan

Clarion Co., Ltd.

Export Division - 22-3, Shibuya 2-chome, Shibuyaku, Tokyo, 150-8335 Japan Tel: 03-3400-1121

Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: 048-443-1111 FAX:048-433-6996

298-5761-00 Aug.1999 P

Service Manual

Model

PEUGEOT Automobile Genuine

RDS/FM/MW/LW Radio CD Stereo

PU-2294A

(Genuine No. 96 346 766 80)

PU-2325A

(Genuine No. 96 373 095 80)

CITROEN Automobile Genuine

RDS/FM/MW/LW Radio CD Stereo

PU-2294B

(Genuine No. 96 346 767 80)

■SPECIFICATIONS

Radio section

Tuning system: PLL frequency synthesizer system

Receive range: FM 87.5MHz to 108.0MHz

MW 531kHz to 1,602kHz

LW 153kHz to 279kHz

Intermediate frequency:

FM 10.7±0.2MHz

MW 450±3kHz

LW 450±3kHz

Quieting sensitivity: FM Less than 13dBμ(30dB S/N)

MW Less than 36dBμ(20dB S/N)

LW Less than 43dBμ(20dB S/N)

Separation: FM More than 20dB

Auto tuning stop sensitivity:

FM 22±8dBμ(DX)

45±10dBμ(LO)

MW30±10dBμ(DX)

60±10dBμ(LO)

LW 30±10dBμ(DX)

60±10dBμ(LO)

CD player section

Separation: More than 65dB

S/N ratio: More than 80dB

Distortion: Less than 1.0％

General

Load impedance: 4Ω

Output power: More than 10W×4

Power supply voltage: DC13.5V

Negative ground

Current consumption: Less than 10A

Dimensions(mm): 178(W)×50(H)×165(D)

Weight: 1.45kg

※Specifications and design are subject to change without

notice for further improvement.

■COMPONENTS

PU-2294A-A/PU-2294B-A/PU-2325A-A

Main unit −−−−− 1

■NOTE

※We cannot supply PWB with component parts in prin-

ciple. When a circuit on PWB has failure , please repair

it by component parts base. Parts which are not men-

tioned in service manual are not supplied.

PU-2294A/B

PU-2325A

■To engineers in charge of repair or

inspection of our products.

Before repair or inspection, make sure to follow

the instructions so that customers and Engineers

in charge of repair or inspection can avoid suf-

fering any risk or injury.

1. Use specified parts.

The system uses parts with special safety features against

fire and voltage. Use only parts with equivalent charac-

teristics when replacing them.

The use of unspecified parts shall be regarded as re-

modeling for which we shall not be liable. The onus of

- 2 -

PU-2294A/B

PU-2325A

product liability (PL) shall not be our responsibility in

cases where an accident or failure is as a result of un-

specified parts being used.

2. Place the parts and wiring back in their original positions

after replacement or re-wiring.

For proper circuit construction, use of insulation tubes,

bonding, gaps to PWB, etc, is involved. The wiring con-

nection and routing to the PWB are specially planned

using clamps to keep away from heated and high voltage

parts. Ensure that they are placed back in their original

positions after repair or inspection.

If extended damage is caused due to negligence during

repair, the legal responsibility shall be with the repairing

company.

3. Check for safety after repair.

Check that the screws, parts and wires are put back se-

curely in their original position after repair. Ensure for

safety reasons there is no possibility of secondary

ploblems around the repaired spots.

If extended damage is caused due to negligence of re-

pair, the legal responsibility shall be with the repairing

company.

4. Caution in removal and making wiring connection to the

parts for the automobile.

Disconnect the battery terminal after turning the ignition

key off. If wrong wiring connections are made with the

battery connected, a short circuit and/or fire may occur.

If extensive damage is caused due to negligence of re-

pair, the legal responsibility shall be with the repairing

company.

5. Cautions regarding chips.

Do not reuse removed chips even when no abnormality

is observed in their appearance. Always replace them

with new ones. (The chip parts include resistors, capaci-

tors, diodes, transistors, etc). The negative pole of tanta-

lum capacitors is highly susceptible to heat, so use spe-

cial care when replacing them and check the operation

afterwards.

6. Cautions in handling flexible PWB

Before working with a soldering iron, make sure that the

iron tip temperature is around 270℃. Take care not to

apply the iron tip repeatedly(more than three times)to the

same patterns. Also take care not to apply the tip with

force.

7. Turn the unit OFF during disassembly and parts replace-

ment. Recheck all work before you apply power to the

unit.

8. Cautions in checking that the optical pickup lights up.

The laser is focused on the disc reflection surface through

the lens of the optical pickup. When checking that the

laser optical diode lights up, keep your eyes more than

30cms away from the lens. Prolonged viewing of the la-

ser within 30cms may damage your eyesight.

9. Cautions in handling the optical pickup

The laser diode of the optical pickup can be damaged by

electrostatic charge caused by your clothes and body.

Make sure to avoid electrostatic charges on your clothes

or body, or discharge static electricity before handling the

optical pickup.

9-1. Laser diode

The laser diode terminals are shorted for transpor-

tation in order to prevent electrostatic damage.

After replacement, open the shorted circuit. When

removing the pickup from the mechanism, short

the terminals by soldering them to prevent this

damage.

9-2. Actuator

The actuator has a powerful magnetic circuit. If a

magnetic material is put close to it. its characteris-

tics will change. Ensure that no foreign substances

enter through the ventilation slots in the cover.

9-3. Cleaning the lens

Dust on the optical lens affects performance. To

clean the lens, apply a small amount of isopropylalcohol

to lens paper and wipe the lens gently.

■CAUTIONS

This appliance contains a laser system and is classified as

a "CLASS 1 LASER PRODUCT".In case of any trouble with

this player,please contact your nearest "authorized service

station".To prevent direct exposure to the laser beam,do

not to open the enclosure.

■COMPUTER ANTI-THEFT SYSTEM

This unit has built-in Computer Anti-Theft System(CATS)

which makes the radio inoperative if power to the unit is

interrupted for any reason whatsoever(including disconnec-

tion and reconnection of the car battery).The radio will re-

main inoperative unless you enter the correct CATS code

number.

Release CATS

1. Press the power button to turn on the power.

("CODE" appears on the display,and "----" appears 3

seconds later)

2. Press 1,2,3 or 4 button the number of times necessary

for the secret number(CATS code) and display the code

number.

3. If the input code number is correct,the radio turn on.

A radio frequency appears on the display.

4. If the input code number is incorrect,"1 ERROR"appears

on the display,and "----" re-appears 5 seconds later.

"1 ERROR" to "3 ERROR"→Waiting time(5 seconds)

"4 ERROR" to "6 ERROR"→Waiting time(5 minutes)

"7 ERROR" to "14 ERROR"→Waiting time(30 minutes)

- 3 - PU-2294A/B

PU-2325A

Item Procedure Measuring

instrument

■ADJUSTMENTS

FM S-meter 1. Press the RDS button and M6 button to set RDS test mode.

2. Input a 98.1MHz/30dBμ(1kHz,30％mod) signal.

3. Adjust VR101 of the tuner pack so that an output of TP101 is 2.8V.

■BLOCK DIAGRAM

BL101

FM /M W /LW TUNER

7.2M H z

PLL-IC

LC 72146

IC 103

RDS-DEC O DER

SAA657

IC 102

ELEC TR O NIC-

VO LU M E

LC 75386

IC 2 0 1

PO W ER-IC

TD A7385

IC 3 0 1

4.33M H z

12M H z

ISO CONNECTOR

PO W ER

SUPPLY

M ECHANISM

EEPRO M

N M 3C 46

IC 803

SYSTEM CO NTRO L

uP D 784216B G C

IC 801

ROTARY

ENCODER

VR101

LCD DISPLAY

LC D 101 KEY M ATRIX

LCD DRIVER

LC 75854

IC 101

VAN

CONTROLLER

TSS461

IC 401

VAN

TRANSCEIVER

MTC30521

IC 402

4M H z

■EXPLANATION OF IC

■μPD784216BGC-102-8EU 052-1157-00 CD, Radio, VAN-Bus

Controller

1. Outward Form : 100 pins QFP

2. Terminal Description

pin 1 : LCD DO : O : LCD data output.

pin 2 : LCD CLK : O : LCD clock output.

pin 3 : LCD CE : O : LCD chip enable signal output.

pin 4 : RDS DATA : IN : RDS serial data input.

pin 5 : NOISE CLR : O : Noise clear signal output.

pin 6 : RDS MUTE : O : "H"= RDS mute ON.

pin 7 : FM SD : IN : "H"= FM station detected.

pin 8 : AM SD : IN : "H"= AM station detected.

pin 9 : VDD : - : Positive supply voltage.

pin 10 : X 2 : - : Crystal connection (12MHz).

pin 11 : X 1 : IN : Crystal connection (12MHz).

pin 12 : VSS : - : Ground.

pin 13 : XT 2 : - : Not in use.

pin 14 : XT 1 : IN : Not in use.

pin 15 : RESET_ : IN : Reset signal input. "L"= Reset.

pin 16 : SUB SYNC : IN : Sub cord block synchronizing pulse input

from CD.

pin 17 : VAN INT_ : IN : VAN interrupt signal input. Negative logic.

pin 18 : RDS CLCK : IN : RDS clock pulse input.

pin 19 : LCD DI : IN : LCD data input.

pin 20 : BACKUP DET : IN : Backup interrupt signal input.

"H"= Backup ON.

pin 21 : ACC DET_ : IN : ACC ON signal input. "L"= ACC ON.

pin 22 : CATS DET_ : IN : "L"= ISO connector pulled off.

pin 23 : A VDD : - : Positive supply voltage.

pin 24 : A Vref 0 : - : Reference voltage input for A/D convert-

er.

pin 25 : NOISE IN : IN : Input terminal of A/D converter to detect

the Noise of FM.

pin 26 : N.C. : IN : Not in use.

pin 27 : S METER : IN : Input terminal of Internal A/D converter to

detect the Voltage of FM S meter.

pin 28 : DG PHNT IN : IN : Input terminal of Internal A/D converter to

detect the PHANTOM circuit.

Ref. Table 1.

pin 29 : PLL DI : IN : PLL serial data input.

pin 30 : REMOCON 1 : IN : Remote control signal input.

pin 31 : REMOCON 2 : IN : Remote control signal input.

pin 32 : MUTE DET : IN : Input terminal of Internal A/D converter to

detect the Voltage of Backup Line.

pin 33 : A VSS : - : Ground.

pin 34 : SD SPD UP : O : FM SD speed control signal output.

"L"= FM seek.

pin 35 : EEPROM DI : IN : Serial data input from EEPROM.

pin 36 : A Vref 1 : - : Connect to VDD.

pin 37 : PLL/ROM DO : O : Serial data output to PLL and EEPROM.

pin 38 : PLL/ROM CK : O : Clock pulse output to PLL and EEPROM.

pin 39 : EEPROM CE : O : Chip enable signal output to EEPROM.

pin 40 : PLL CE : O : Chip enable signal output to PLL.

pin 41 : DG PHN OUT : O : Diagnosis Phantom signal output.

Ref. Table 1.

pin 42 : A MUTE_ : O : Mute signal output to Audio power ampli-

fier IC. "L"= Mute ON.

pin 43 : JBL AMP RM : O : "H"= External Audio amplifier ON.

pin 44 : BEEP : O : Beep output.

pin 45 : VOL CLK : O : Clock pulse output to Electric volume IC.

pin 46 : VOL DATA : O : Serial data output to Electric volume IC.

pin 47 : VOL CE : O : Chip enable signal output to Electric vol-

ume IC.

pin 48 : VOL MUTE_ : O : Mute signal output to Electric volume IC.

"L"= Mute ON.

pin 49 : 5V REM_ : O : 5V power supply circuit control signal out-

put. "L"= ON.

pin 50 : 14V REM : O : 14V power supply circuit control signal

output. "H"= ON.

pin 51 : +VAN ON : O : "H"= ACC(+VAN)ON.

pin 52 : TEL MUTE : IN : "H"= Tel mute ON.

pin 53 : EEPROM INI_ : IN : EEPROM initialize command input.

Negative logic.

pin 54 : CD 8V ON : O : CD 8V power supply circuit control signal

output. "H"= ON.

pin 55 : CD 5V ON : O : CD 5V power supply circuit control signal

output. "H"= ON.

SSG

Milli volt meter

- 4 -

PU-2294A/B

PU-2325A

pin 56 : AD 0 : I/O : Data input/output terminal of VAN-Bus.

pin 57 : AD 1 : I/O : Data input/output terminal of VAN-Bus.

pin 58 : AD 2 : I/O : Data input/output terminal of VAN-Bus.

pin 59 : AD 3 : I/O : Data input/output terminal of VAN-Bus.

pin 60 : AD 4 : I/O : Data input/output terminal of VAN-Bus.

pin 61 : AD 5 : I/O : Data input/output terminal of VAN-Bus.

pin 62 : AD 6 : I/O : Data input/output terminal of VAN-Bus.

pin 63 : AD 7 : I/O : Data input/output terminal of VAN-Bus.

pin 64 : AREA A : IN : Destination select input. Ref. Table 2.

pin 65 : AREA B : IN : Destination select input. Ref. Table 2.

pin 66 : JBL_ : IN : "L"= With external amplifier.

pin 67 : CITR_/PEUG : O : "L"= Citroen, "H"= Peugeot.

pin 68 : CD 0 FLAG : IN : 0 flag input from CD.

pin 69 : CD BUS 0 : I/O : Data bus line connected to CD.

pin 70 : CD BUS 1 : I/O : Data bus line connected to CD.

pin 71 : CD BUS 2 : I/O : Data bus line connected to CD.

pin 72 : VSS : - : Ground.

pin 73 : CD BUS 3 : I/O : Data bus line connected to CD.

pin 74 : CD DET : IN : Not in use.

pin 75 : VAN WU : O : Wake up signal output to VAN IC.

pin 76 : VAN RESET : O : Reset signal output to VAN IC.

pin 77 : VAN RD_ : O : Read strobe signal output to VAN IC.

Negative logic.

pin 78 : VAN WR_ : O : Write strobe signal output to VAN IC.

Negative logic.

pin 79 : VAN CS : O : Chip select signal output to VAN IC.

pin 80 : VAN ALE : O : Latch strobe signal output to VAN IC.

pin 81 : VDD : - : Positive supply voltage.

pin 82 : N.C. : IN : Not in use.

pin 83 : CD BUCK : O : Clock pulse output to CD.

pin 84 : CD CEE_ : O : Chip enable signal output to CD.

pin 85 : CD RESET_ : O : Reset pulse output to CD.

"L"= Reset.

pin 86 : CD CHU SW : IN : Chuking signal input from CD.

pin 87 : CD TR A : IN : Photo sensor signal input from CD.

pin 88 : CD TR B : IN : Photo sensor signal input from CD.

pin 89 : CD TR C : IN : Photo sensor signal input from CD.

pin 90 : CD CCW : O : Loading motor control signal output.

Ref. Table 3.

pin 91 : CD CW : O : Loading motor control signal output.

Ref. Table 3.

pin 92 : VOL A : IN : Volume control pulse input from Volume

switch.

pin 93 : VOL B : IN : Volume control pulse input from Volume

switch.

pin 94 : VPP : - : Connect to ground.

pin 95 : N.C. : IN : Not in use.

pin 96 : N.C. : IN : Not in use.

pin 97 : N.C. : IN : Not in use.

pin 98 : N.C. : IN : Not in use.

pin 99 : N.C. : IN : Not in use.

pin100 : N.C. : IN : Not in use.

pin 3 : UHSO : O : Playback mode flag output. Ref. Table 1.

pin 4 : EMPH : O : Emphasis flag output of Sub cord Q data.

"H"= emphasis ON.

pin 5 : LR CK : O : Channel clock output. (44.1kHz)

pin 6 : VSS : −: Ground.

pin 7 : B CK : O : Bit clock output. (1.4122MHz)

pin 8 : A OUT : O : Audio data output.

pin 9 : D OUT : O : Digital output.

pin 10 : MBOV : O : Buffer memory over signal output.

pin 11 : IPF : O : Compensation flag output.

pin 12 : SBOK : O : CRCC judgement output of Sub Q data.

"H"=OK.

pin 13 : CLOCK : I/O : Clock output/input to read Sub cord P to

pin 14 : VDD : −: Positive supply voltage terminal.

pin 15 : VSS : −: Ground.

pin 16 : DATA : O : Sub cord P to W data output.

pin 17 : SF SY : O : Frame synchronize signal output.

pin 18 : SB SY : O : Sub cord block synchronize signal output.

pin 19 : SP CK : O : Clock signal output to read processor sta-

tus. (176.4kHz)

pin 20 : SP DA : O : Processor status signal output.

pin 21 : COFS : O : Correction frame clock output. (7.35kHz)

pin 22 : MONIT : O : Not in use.

pin 23 : VDD : −: Positive supply voltage terminal.

pin 24 : TESIO0 : IN : Not in use.

pin 25 : P2Vref : −: (Reference voltage)×2 terminal for PLL.

pin 26 : HSSW : O : pin26=Vref : ×2-speed or ×4-speed.

pin 27 : Z DET : O : 0 flag output of 1 bit DAC.

pin 28 : PDO : O : Error signal output. (EFM - PLCK)

pin 29 : TMAX S : O : TMAX detect signal output.

pin 30 : TMAX : O : TMAX detect signal output.

pin 31 : LPF N : IN : Inverted input of amplifier for LPF.

pin 32 : LPF O : O : Output of amplifier for LPF.

pin 33 : PVref : −: Reference voltage terminal for PLL.

pin 34 : VCOref : −: Reference voltage terminal for VCO.

pin 35 : VCO F : O : Output of filter for VCO.

pin 36 : AVSS : −: Analog ground.

pin 37 : SLCO : O : Output of DAC for data slice level.

pin 38 : RF IN : IN : RF signal input.

pin 39 : AVDD : −: Positive voltage supply for analog.

pin 40 : RFCT : IN : Center level input of RFRP signal.

pin 41 : RFZI : IN : RFRP 0 cross.

pin 42 : RFRP : IN : RF ripple signal input.

pin 43 : FEI : IN : Focus error signal input.

pin 44 : SBAD : IN : Sub beam addition signal input.

pin 45 : TSIN : IN : Not in use.

pin 46 : TEI : IN : Tracking error input.

pin 47 : TEZI : IN : Tracking error , 0 cross input.

pin 48 : FO O : O : Focusing equalizer output.

pin 49 : TR O : O : Tracking equalizer output.

pin 50 : Vref : −: Reference voltage for analog.

pin 51 : RFGC : O : RF gain control signal output.

pin 52 : TEBC : O : Tracking balance control signal output.

pin 53 : FM O : O : Field equalizer output.

pin 54 : FVO : O : Field error or Field search EQ output.

pin 55 : DMO : O : Disc equalizer output.

pin 56 : 2Vref : −:2×Vref for analog.

pin 57 : SEL : O : Laser ON and UHS="H" : output "H"

pin 58 : FLG A : O : Monitor signal output.

pin 59 : FLG B : O : Monitor signal output.

pin 60 : FLG C : O : Monitor signal output.

pin 61 : FLG D : O : Monitor signal output.

pin 62 : VDD : −: Positive supply voltage.

pin 63 : VSS : −: Ground.

pin 64 : IO 0 : I/O : I/O port.

pin 65 : IO 1 : I/O : I/O port.

pin 66 : IO 2 : I/O : I/O port.

pin 67 : IO 3 : I/O : I/O port.

pin 68 : DMOUT : IN : Not in use.

pin 69 : CKSE : IN : Not in use.

pin 70 : DACT : IN : Not in use.

pin 71 : TESIN : IN : Not in use.

pin 72 : TESIO1 : IN : Not in use.

pin 73 : VSS : −: Ground.

pin 74 : PX I : IN : DSP oscillator input.

pin 75 : PX O : O : DSP oscillator output.

pin 76 : VDD : −: Positive supply voltage.

pin 77 : X VSS : −: Ground for system oscillator clock.

pin 78 : X I : IN : System clock oscillator input.

pin 79 : X O : O : System clock oscillator output.

pin 80 : X VDD : −: Positive supply voltage for system clock

oscillator.

pin 81 : D VSR : −: Positive supply voltage for right channel

Table 1. Diagnosis Phantom signal output

Input voltage of pin 28 (DG PHNT IN) DG PHN OUT(pin41)

0.00V to 0.93V L

0.94V to 2.82V H

2.83V to 5.00V L

Table 2. Destination select input

AREA A(pin64) AREA B(pin65)

Europe H H

South America H L

Saudi Arabia L H

Asia L L

Table 3. Loading motor control signal output

Loading Eject Brake Stop

CD CW (pin 91) H L H L

CD CCW(pin 90) L H H L

■TC9462F 051-6342-00 Digital signal processor for CD

1. Outward Form : 100 pins QFP

2. Function : Sync. separation, EFM, Error correction

3. Terminal Description

pin 1 : TEST0 : IN : Not in use.

pin 2 : HSO : O : Playback mode flag output. Ref. Table 1.

- 5 - PU-2294A/B

PU-2325A

DAC.

pin 82 : R O : O : Right channel data non-inverted output.

pin 83 : D VDD : −: Positive supply voltage for DAC.

pin 84 : D Vref : −: Reference voltage.

pin 85 : L O : O : Left channel data non-inverted output.

pin 86 : D VS L : −: Positive supply voltage for left channel

DAC.

pin 87 : TEST 1 : IN : Not in use.

pin 88 : TEST 2 : IN : Not in use.

pin 89 : TEST 3 : IN : Not in use.

pin 90 : BUS 0 : I/O : Data bus to micro computer.

pin 91 : BUS 1 : I/O : Data bus to micro computer.

pin 92 : BUS 2 : I/O : Data bus to micro computer.

pin 93 : BUS 3 : I/O : Data bus to micro computer.

pin 94 : VDD : −: Positive supply voltage.

pin 95 : VSS : −: Ground.

pin 96 : BUS CK : IN : Clock input for data bus.

pin 97 : CCE : IN : Chip enable signal input. Negative logic.

pin 98 : TEST 4 : IN : Not in use.

pin 99 : TS MOD : IN : Not in use.

pin100 : RST : IN : Reset signal input. Negative logic.

Table 1. Playback speed flag.

Play back speed UHSO(pin3) HSO(pin2)

Normal speed ×1HH

Normal speed ×2HL

Normal speed ×4LH

------------------------ L L

■EXPLODED VIEW・PARTS LIST

Main section

26 20

22 723 24

41 18

53 54

42 2

14 15

117

NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

1 311-1765-01 LOWER CASE 1

2 750-3328-00 SPRING 1

3 750-3329-00 SPRING 1

4 312-0433-10 MAIN CHASSIS 1

5 039-1429-01 MAIN PWB 1

(WITHOUT COMPONENT)

6 076-0540-18 PLUG(18P) 1

7 714-2606-81 MACHINE SCREW(M2.6×6) 4

8 039-1427-00 ISO PWB 1

(WITHOUT COMPONENT)

9 076-0324-10 PLUG(10P) 1

10 051-2013-00 IC(TDA7385) 1

11 074-1159-02 OUTLET SOCKET 1

12 060-0057-56 AUTO-FUSE(10A) 1

13 880-2084A TUNER ASSY(FM/MW/LW) 1

14 009-9006-60 CHOKE 1

15 331-2577-00 ISO HOLDER 1

16 076-0324-14 PLUG(14P) 1

17 074-1186-26 OUTLET SOCKET(26P) 1

18 039-1432-00 SWITCH PWB 1

(WITHOUT COMPONENT)

19 331-2574-00 IC HOLDER 1

20 731-2608-80 TAPTIGHT(M2.6×8) 9

(NOTE) Some parts depend on each model.The model name is specified in the description.

- 6 -

PU-2294A/B

PU-2325A

21 331-2637-00 MECH BRKT 1

22 313-1750-00 HEAT SINK 1

23 716-1831-00 REAR BOLT 1

24 345-4847-01 STOPPER 1

25 929-0069-83 CD MECHANISM 1

26 310-1669-02 UPPER CASE 1

27 716-0878-00 IT-SCREW(2.6×5) 2

28 731-3008-40 TAPTIGHT(M3×8) 2

29 714-2610-81 MACHINE SCREW(M2.6×10) 2

30 380-5439-00 KNOB 1

31 940-7862-64 ESCUTCHEON ASSY 1

(PU-2294A/B)

940-7892-63 ESCUTCHEON ASSY

(PU-2325A)

32 331-2573-00 SHIELD CASE 1

33 331-2578-00 SHIELD CASE 1

34 309-0720-02 FRONT PLATE 1

35 286-8497-26 SETPLATE(PU-2294A) 1

286-8497-27 SETPLATE(PU-2294B)

286-8497-28 SETPLATE(PU-2325A)

36 716-0778-00 WAVE SCREW(φ2×6) 4

37 013-3741-11 SWITCH 18

38 016-0010-13 VARIABLE RESISTOR 1

39 017-0454-01 PILOTLAMP 5

(PU-2294A/ORG/14V40mA)

017-0454-02 PILOTLAMP

(PU-2294B/GRN/14V40mA)

017-0454-03 PILOTLAMP

(PU-2325A/ORG/14V40mA)

40 074-1151-18 OUTLET SOCKET(18P) 1

41 816-2488-00 FLAT WIRE 1

42 714-2303-81 MACHINE SCREW(M2.3×3) 5

43 331-2593-00 LCD HOLDER 1

44 335-5994-00 SHIELD SHEET 1

45 379-1155-41 INDICATOR 1

(PU-2294A/PU-2325A)

379-1155-40 INDICATOR(PU-2294B)

46 335-5911-01 FILTER(PU-2294A/PU-2325A) 1

335-5912-01 FILTER(PU-2294B)

47 335-5910-00 ILLUMI PLATE 1

48 335-5909-00 LCD HOLDER 1

49 331-2638-00 SHIELD CASE 1

50 331-2639-00 SHIELD CASE 1

51 285-1633-10 GUIDE LABEL(CLASS1) 1

52 345-8316-00 INSULATOR 1

53 345-3814-82 LAMP CAP(PU-2294A/ORG) 2

345-3814-81 LAMP CAP(PU-2294B/GRN)

345-3814-83 LAMP CAP(PU-2325A/ORG)

54 017-0455-00 PILOTLAMP(9V65mA) 2

55 285-1628-00 GUIDE LABEL 1

56 285-1627-00 GUIDE LABEL 1

57 347-6200-00 INSULATOR 1

58 347-6217-00 INSULATOR(PU-2294A/B) 1

NO. PART NO. DESCRIPTION Q'TY CD mechanism section:929-0069-83

1 HBS-463-100 DRIVE UNIT 1

1-1 966-0314-21 STOP LINK ASSY 1

1-2 966-0447-22 DR-PLATE ASSY 1

1-3 966-0448-21 SIDE PLATE ASSY 1

1-4 966-0449-22 CLAMP LINK ASSY 1

1-5 969-0050-51 PICK UP UNIT 1

1-6 013-7100-00 LIMIT SWITCH 1

1-7 620-0198-03 CLAMPER PLATE 1

1-8 620-0491-03 SPRING PLATE 1

1-9 620-0690-01 RATTLE PLATE 1

1-10 621-0205-02 CLAMPER LINK 1

1-11 621-0251-03 ROCK LINK 1

1-12 621-0252-03 DISC STOPPER 1

1-13 621-0253-02 MOTOR HOLDER 1

1-14 621-0255-02 SECOND GEAR 1

1-15 621-0375-00 SH-BASE 1

1-16 621-0357-03 PICK UP GUIDE 1

1-17 621-0358-02 LS-HOLDER F 1

1-18 621-0359-02 LS‐HOLDER R 1

1-19 622-1073-02 CLAMPER ROLLER 1

1-20 714-2003-81 MACHINE SCREW(M2×3) 10

1-21 716-0675-00 SCREW(M2×2.5) 2

1-22 716-1468-00 SCREW(M2×2.5) 2

1-23 716-1555-00 WAVE SCREW 1

1-24 716-1733-00 SCREW(M2×2.5) 2

1-25 732-2004-11 SEMS SCREW 2

1-26 739-1735-17 PRECISION SCREW 2

1-27 746-0761-00 SCREW(M2×2.5) 2

1-28 750-3097-03 CLAMPER SPRING 1

1-29 750-3098-00 L-LINK SPRING 1

1-30 750-3099-00 ES-SPRING 1

1-31 816-2372-00 WIRE(BLU) 1

1-32 816-2373-00 WIRE(WHT) 1

1-33 966-0454-00 SH-ROCK ASSY 1

1-34 HBS-432-100 LS-GEAR ASSY 1

1-35 SMA-146-100 SLED MOTOR ASSY 1

1-36 SMA-151-100 SPINDLE MOTOR ASSY 1

2 966-0308-10 CHASSIS ASSY 1

3 966-0309-20 L-DISC-G-ASSY 1

4 966-0310-21 SHIFT-P-CH-ASSY 1

5 966-0312-21 SHIFT-P-ASSY 1

6 966-0358-21 DRIVE-L-PL-ASSY 1

7 966-0359-21 SIDE-L-PL-ASSY 1

8 013-3879-01 CHUCKING SWITCH 1

9 039-0586-01 CHUCKING SWITCH PWB 1

(WITHOUT COMPONENT)

10 039-0588-01 SENSOR PWB 1

(WITHOUT COMPONENT)

11 060-0252-01 PHOTO TR (PT4850F) 3

12 345-7513-01 CLAMPER SHEET 1

13 345-7514-00 S-PWB SHEET 1

14 620-0485-04 FRONT PLATE 1

NO. PART NO. DESCRIPTION Q'TY

- 7 - PU-2294A/B

PU-2325A

NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

1-1

1-22

1-7

1-30

1-11

1-2

1-10

1-20

1-4

1-27

1-1

1-12

1-3

1-2

1-20 1-16 4 1-17

1-28

1-24

1-20

1-18

1-20

1-25

1-14

1-20

1-13

1-20

1-35

1-31

1-32

1-26

1-15

1-33

1-34

1-5

1-8

1-21

1-20

1-23

1-6

1-32

1-31

1-36

A11

A10

H1 H2

Z1 Z2

15 620-0488-01 S-L-LINK PLATE 1

16 620-0489-02 MOTOR PLATE 1

17 620-0492-01 MOTOR BRACKET 1

18 620-0773-81 MECH BRACKET 1

19 621-0402-01 U-DISC GUIDE F 1

20 621-0243-02 ROLLER SLAVE 2

21 621-0248-07 RACK GEAR 1

22 621-0249-02 ROLLER GEAR 1

23 621-0250-01 DAMPER HOLDER 4

24 621-0258-03 LOADING ROLLER 2

25 622-1072-05 ROLLER SHAFT 1

26 622-1219-01 SHIFT ROLLER 1

27 629-0058-00 DAMPER-VA 4

28 714-2003-81 MACHINE SCREW(M2X3) 8

29 714-2603-81 MACHINE SCREW(M2.6X3) 5

30 716-1468-00 SCREW(M2×2.5) 2

31 716-1507-00 SCREW(M2×3) 2

32 716-1670-00 SCREW(M2×3) 6

33 716-1677-00 SCREW(M2×5) 1

34 716-1704-00 SCREW(M2×7) 1

35 716-1742-00 SCREW(M2×5) 1

36 743-1500-10 E-RING 3

37 746-0712-03 WASHER 1

38 746-0762-00 WASHER 1

39 746-0877-02 WASHER 2

40 750-3090-02 RO-SPRING L 1

41 750-3091-03 RO-SPRING R 1

42 750-3092-03 SHIFT SPRING 1

43 750-3094-00 S-ARM SPRING 1

44 750-3096-01 DR-SPRING R 1

45 750-3098-00 L-LINK SPRING 1

46 750-3164-00 DR-SPRING-LR 1

- 8 -

PU-2294A/B

PU-2325A

NO. PART NO. DESCRIPTION Q'TY

227

51 54

38 20

28 14

43 56

55 52

A11

E1 C2

A1 A10

47 750-3188-00 DR-SPRING-F-B 1

48 750-3189-00 SIDE-L-SPRING 1

49 750-3201-00 DR-SPRING-F-R 1

50 750-3202-00 CENTER SPRING-B 1

51 800-4904-60 WIRE(BLK) 1

52 800-4910-60 WIRE(BLK) 1

53 801-4910-60 WIRE(BRN) 1

54 802-4904-60 WIRE(RED) 1

55 802-4910-60 WIRE(RED) 1

56 804-4910-60 WIRE(YEL) 1

57 001-0563-00 DIODE 3

58 HBS-430-100 GEAR PLATE ASSY 1

59 039-1088-03 CD MECH PWB 1

(WITHOUT COMPONENT)

60 SMA-147-100 LOADING MOTOR ASSY 1

- 9 - PU-2294A/B

PU-2325A

■ELECTRICAL PARTS LIST

Main PWB section(B1)

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION

Note) Several different parts of the same reference number are alternative parts.

One of those parts is used in the set.

Some parts depend on each model.The model name is specified in the description.

BL101 880-2084A FM/MW/LW

C1 183-1063-31 16V10μF

C2 178-3332-78 0.033μF

C3 178-1042-78 0.1μF

C4 176-2201-00 22pF CH

C5 178-1042-78 0.1μF

C6 183-4763-11 6.3V47μF

C101 178-2232-78 0.022μF

C102 178-2232-78 0.022μF

C103 178-3322-78 3300pF

C105 183-2253-62 50V2.2μF

C106 178-3312-78 330pF

C107 178-5612-78 560pF

C108 176-4701-00 47pF CH

C109 176-8201-00 82pF CH

C110 178-2232-78 0.022μF

C111 178-1042-78 0.1μF

C113 183-4763-11 6.3V47μF

C114 178-1022-78 1000pF

C115 178-2212-78 220pF

C116 178-4732-78 0.047μF

C117 178-2232-78 0.022μF

C118 178-2232-78 0.022μF

C121 178-2232-78 0.022μF

C122 178-1532-78 0.015μF

C123 178-8222-78 8200pF

C124 178-1222-78 1200pF

C125 178-1042-78 0.1μF

C126 178-2212-78 220pF

C127 178-1032-78 0.01μF

C128 178-6822-78 6800pF

C129 183-1053-61 50V1μF

C130 178-1532-78 0.015μF

C131 176-1011-00 100pF CH

C132 178-1532-78 0.015μF

C133 176-1011-00 100pF CH

C134 176-1011-00 100pF CH

C136 183-4763-11 6.3V47μF

C137 176-1501-00 15pF CH

C138 183-2253-62 50V2.2μF

C139 183-2253-62 50V2.2μF

C140 176-1801-00 18pF CH

C141 178-1042-78 0.1μF

C142 178-1032-78 0.01μF

C143 178-1042-78 0.1μF

C144 178-4732-78 0.047μF

C145 178-1032-78 0.01μF

C146 178-1032-78 0.01μF

C147 176-1011-00 100pF CH

C148 178-1222-78 1200pF

C149 178-1222-78 1200pF

C201 178-1032-78 0.01μF

C202 178-1032-78 0.01μF

C203 183-4753-51 35V4.7μF

C206 183-2263-11 6.3V22μF

C207 183-2263-11 6.3V22μF

C210 183-4753-51 35V4.7μF

C211 042-0505-04 10V33μF

C212 178-4732-78 0.047μF

C213 178-4732-78 0.047μF

C214 176-4711-00 470pF CH

C215 183-1053-61 50V1μF

C216 183-1053-61 50V1μF

C217 176-4711-00 470pF CH

C218 183-1063-31 16V10μF

C219 183-1063-31 16V10μF

C220 183-1063-31 16V10μF

C221 183-1063-31 16V10μF

C222 183-1056-61 50V1μF NP

C223 183-1056-61 50V1μF NP

C224 178-3332-78 0.033μF

C225 178-3332-78 0.033μF

C226 178-1032-78 0.01μF

C227 178-1032-78 0.01μF

C228 178-3312-78 330pF

C229 178-3312-78 330pF

C230 183-1063-31 16V10μF

C231 183-1063-31 16V10μF

C232 178-1042-78 0.1μF

C233 183-4743-61 50V0.47μF

C234 183-4743-61 50V0.47μF

C235 183-4743-61 50V0.47μF

C236 183-4743-61 50V0.47μF

C237 178-1032-78 0.01μF

C238 178-1032-78 0.01μF

C239 178-2732-78 0.027μF

C301 183-1053-61 50V1μF

C302 183-4763-31 16V47μF

C303 178-1022-78 1000pF

C304 178-1022-78 1000pF

C305 178-1022-78 1000pF

C306 178-1022-78 1000pF

C307 178-4742-78 0.47μF

C308 172-1041-11 0.1μF

C309 184-3383-32 16V3300μF

C310 183-2263-11 6.3V22μF

C401 176-4701-00 47pF CH

C402 176-5601-00 56pF CH

C403 176-3301-00 33pF CH

C404 176-4701-00 47pF CH

C405 176-4701-00 47pF CH

C406 042-0416-05 16V15μF TAN

C407 178-1032-78 0.01μF

C408 042-0452-02 16V100μF

C409 178-1042-78 0.1μF

C410 178-1032-78 0.01μF

C411 176-1511-00 150pF CH

C412 176-1511-00 150pF CH

C413 178-1042-78 0.1μF

C501 178-1042-78 0.1μF

C502 172-2241-11 0.22μF

C503 178-1042-78 0.1μF

C504 183-1073-12 6.3V100μF

C505 178-1032-78 0.01μF

C506 183-3353-61 50V3.3μF

C507 183-1073-12 6.3V100μF

C508 172-2241-11 0.22μF

C509 042-0452-02 16V100μF

C510 178-1032-78 0.01μF

C513 183-1073-21 10V100μF

C514 042-0452-01 10V220μF

C515 183-1043-63 50V0.1μF

C516 042-0427-94 16V47μF TAN

C517 178-1032-78 0.01μF

C518 183-1073-21 10V100μF

C519 172-1031-11 0.01μF

C520 183-4753-51 35V4.7μF

C521 183-4763-51 35V47μF

C522 178-1032-78 0.01μF

C523 178-1032-78 0.01μF

C526 178-1042-78 0.1μF

C601 042-0505-04 10V33μF

C701 183-1053-61 50V1μF

C801 178-6832-78 0.068μF

C802 183-2263-11 6.3V22μF

C803 178-6832-78 0.068μF

C804 183-1073-12 6.3V100μF

C805 176-1501-00 15pF CH

C806 176-1501-00 15pF CH

C807 178-2242-78 0.22μF

C808 178-1032-78 0.01μF

C809 178-1042-78 0.1μF

C810 176-1011-00 100pF CH

C811 178-1532-78 0.015μF

C812 178-1032-78 0.01μF

CCT801 050-0140-54 1kΩ×4

CCT802 050-0140-54 1kΩ×4

CCT803 050-0140-54 1kΩ×4

CCT804 050-0140-54 1kΩ×4

CCT805 050-0140-54 1kΩ×4

CCT806 050-0140-54 1kΩ×4

CCT807 050-0140-54 1kΩ×4

CCT808 050-0140-54 1kΩ×4

CCT809 050-0140-54 1kΩ×4

CCT810 050-0140-52 100Ω×4

CCT811 050-0140-52 100Ω×4

CCT812 050-0140-54 1kΩ×4

CCT813 050-0140-54 1kΩ×4

CCT814 050-0140-54 1kΩ×4

CCT815 050-0140-52 100Ω×4

CCT816 050-0140-54 1kΩ×4

CCT817 050-0140-54 1kΩ×4

CCT818 050-0140-54 1kΩ×4

CCT819 050-0140-54 1kΩ×4

D1 001-0330-00 1SS119

D2 001-2404-90 MA28T-A

D101 001-0330-00 1SS119

D102 001-0330-00 1SS119

D301 001-0330-00 1SS119

D501 001-0330-00 1SS119

D502 001-0330-00 1SS119

D503 001-0376-46 MTZJ9.1A

D504 001-0330-00 1SS119

D505 001-0376-32 MTZJ5.6B

D505 001-0377-32 MA4056M

D506 001-0421-31 MTZJ18

D506 001-0423-31 MA4180

D507 001-0376-46 MTZJ9.1A

D509 001-0376-47 MTZJ9.1B

D509 001-0377-46 MA4091L

D510 001-0376-46 MTZJ9.1A

D510 001-0377-45 MA4082H

D511 001-0376-47 MTZJ9.1B

D512 001-0330-00 1SS119

D514 001-0376-34 MTZJ6.2A(PU-

2294A/PU-2325A)

D514 001-0377-33 MA4056H(PU-

2294A/PU-2325A)

D515 001-0330-00 1SS119

D516 001-0330-00 1SS119

D517 001-0466-00 S5688B

D518 001-0466-00 S5688B

D519 001-0330-00 1SS119

D520 001-0466-00 S5688B

D521 001-0330-00 1SS119

D522 001-0330-00 1SS119

D523 001-0330-00 1SS119

D524 060-0108-00 0ΩJW(PU-2294B)

D525 060-0108-00 0ΩJW(PU-2294A/

PU-2325A)

D526 001-0330-00 1SS119

D527 001-0330-00 1SS119

D528 001-0330-00 1SS119

D529 001-0466-00 S5688B

D530 001-0466-00 S5688B

D801 001-0330-00 1SS119

D802 001-0330-00 1SS119

IC1 051-3027-90 AD820AR

IC101 051-0350-55 NJM4558M

IC102 051-1819-00 SAA6579T

IC103 051-6201-00 LC72146M

IC201 051-5012-00 LC75386

IC202 051-0350-55 NJM4558M

- 10 -

PU-2294A/B

PU-2325A

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION

IC301 051-2013-00 TDA7385

IC401 051-6611-08 TSS461CR

IC402 051-6610-18 MTC-30521

IC501 051-1556-05 S-80740AN-D4-X

IC502 051-1834-00 LM2936

IC801 052-1157-00 μPD784216BGC-

102-8EU

IC802 051-5413-08 S-8052HNM-CR-T1

IC803 051-1375-35 NM93C46TEM8

L1 010-8017-00 22mH

L2 010-2230-68 4.7μH

L3 010-2003-04 COIL

L101 010-2230-64 2.2μH

L102 010-2046-44 1mH

L104 010-2230-88 220μH

L401 010-2230-10 1μH

L402 010-2230-64 2.2μH

L701 010-2230-52 0.22μH

P601 074-1186-26 26P

P701 076-0540-18 18P

Q1 108-0669-00 2SK669

Q2 100-1298-00 2SA1298

Q3 125-2004-02 RN1402

Q4 102-2712-00 2SC2712

Q5 103-1858-00 2SD1858

Q101 125-0002-02 RN2402

Q102 103-1306-00 2SD1306

Q103 125-2004-06 RN1406

Q104 125-2004-02 RN1402

Q105 100-1298-00 2SA1298

Q106 100-1162-00 2SA1162

Q107 108-0669-00 2SK669

Q301 102-2712-00 2SC2712

Q302 125-2004-02 RN1402

Q401 102-2712-00 2SC2712

Q501 102-2712-00 2SC2712

Q502 125-0002-02 RN2402

Q503 103-1858-00 2SD1858

Q504 103-1858-00 2SD1858

Q505 125-0002-02 RN2402

Q506 125-2004-02 RN1402

Q507 100-1298-00 2SA1298

Q508 102-3420-00 2SC3420

Q509 100-1162-00 2SA1162

Q510 125-2004-02 RN1402

Q513 103-1858-00 2SD1858

Q514 103-1858-00 2SD1858

Q515 103-1858-00 2SD1858

Q516 100-1297-00 2SA1297

Q517 125-2004-02 RN1402

Q518 102-2458-00 2SC2458

Q519 103-1858-00 2SD1858

Q520 103-1858-00 2SD1858

Q521 103-1858-00 2SD1858

Q522 125-2004-02 RN1402

Q523 100-1428-00 2SA1428

Q524 125-2004-02 RN1402

Q525 102-2712-00 2SC2712(PU-2294A/

PU-2325A)

Q526 100-1431-00 2SA1431

Q528 102-2712-00 2SC2712

Q529 100-1298-00 2SA1298

Q530 100-0885-00 2SA885-QRS

R1 032-0092-89 1/10W 470Ω±1%

R2 032-0092-88 1/10W 10Ω±1%

R3 032-0092-88 1/10W 10Ω±1%

R4 117-1031-10 1/10W 10kΩ

R5 117-5621-10 1/10W 5.6kΩ

R6 117-3301-10 1/10W 33Ω

R7 111-2221-91 1/4WS 2.2kΩ

R102 117-1231-10 1/10W 12kΩ

R103 117-1031-10 1/10W 10kΩ

R104 117-1821-10 1/10W 1.8kΩ

R105 117-1041-10 1/10W 100kΩ

R106 117-1521-10 1/10W 1.5kΩ

R107 117-1521-10 1/10W 1.5kΩ

R108 117-2221-10 1/10W 2.2kΩ

R109 117-3921-10 1/10W 3.9kΩ

R110 117-3321-10 1/10W 3.3kΩ

R111 117-1041-10 1/10W 100kΩ

R112 111-3311-91 1/4WS 330Ω

R113 117-2211-10 1/10W 220Ω

R114 117-2221-10 1/10W 2.2kΩ

R115 117-1031-10 1/10W 10kΩ

R116 117-1531-10 1/10W 15kΩ

R117 117-1031-10 1/10W 10kΩ

R118 117-2221-10 1/10W 2.2kΩ

R120 117-1031-10 1/10W 10kΩ

R121 117-2221-10 1/10W 2.2kΩ

R122 117-1231-10 1/10W 12kΩ

R123 117-4721-10 1/10W 4.7kΩ

R124 117-2221-10 1/10W 2.2kΩ

R125 117-2711-10 1/10W 270Ω

R126 117-1021-10 1/10W 1kΩ

R127 117-1021-10 1/10W 1kΩ

R128 117-1021-10 1/10W 1kΩ

R129 117-1031-10 1/10W 10kΩ

R130 117-1531-10 1/10W 15kΩ

R131 117-1531-10 1/10W 15kΩ

R132 117-8231-10 1/10W 82kΩ

R133 117-8231-10 1/10W 82kΩ

R134 117-1031-10 1/10W 10kΩ

R135 117-1031-10 1/10W 10kΩ

R206 117-4731-10 1/10W 47kΩ

R207 117-4721-10 1/10W 4.7kΩ

R208 117-6831-10 1/10W 68kΩ

R209 117-6831-10 1/10W 68kΩ

R210 117-4721-10 1/10W 4.7kΩ

R211 117-1541-10 1/10W 150kΩ

R212 117-1021-10 1/10W 1kΩ

R213 117-1021-10 1/10W 1kΩ

R214 117-1021-10 1/10W 1kΩ

R215 117-1021-10 1/10W 1kΩ

R221 117-2231-10 1/10W 22kΩ

R222 117-2231-10 1/10W 22kΩ

R226 117-6821-10 1/10W 6.8kΩ

R227 117-6821-10 1/10W 6.8kΩ

R301 117-1031-10 1/10W 10kΩ

R302 117-1051-10 1/10W 1MΩ

R303 117-1031-10 1/10W 10kΩ

R401 117-4731-10 1/10W 47kΩ

R403 117-4731-10 1/10W 47kΩ

R404 032-0092-90 1/10W 10kΩ±1%

R405 111-4321-91 1/4WS 4.3kΩ

R406 111-4321-91 1/4WS 4.3kΩ

R407 111-5101-91 1/4WS 51Ω

R408 111-5101-91 1/4WS 51Ω

R409 060-0108-00 1/6ZP 0ΩJW

R501 117-2231-10 1/10W 22kΩ

R502 117-4731-10 1/10W 47kΩ

R503 032-0092-02 1/10W 220kΩ±1%

R504 117-2221-10 1/10W 2.2kΩ

R505 117-6821-10 1/10W 6.8kΩ

R506 032-0092-36 1/10W 470kΩ±1%

R507 111-1021-91 1/4WS 1kΩ

R508 111-1091-91 1/4WS 1Ω

R509 111-1091-91 1/4WS 1Ω

R510 117-2231-10 1/10W 22kΩ

R511 117-1021-10 1/10W 1kΩ

R512 111-2211-91 1/4WS 220Ω

R513 117-4741-10 1/10W 470kΩ

R514 117-1031-10 1/10W 10kΩ

R515 117-1031-10 1/10W 10kΩ

R516 117-2741-10 1/10W 270kΩ

R517 111-1811-81 1/2WS 180Ω

R520 111-1091-91 1/4WS 1Ω

R521 111-1091-91 1/4WS 1Ω

R522 111-1091-91 1/4WS 1Ω

R523 111-2211-81 1/2WS 220Ω

R525 111-4711-81 1/2WS 470Ω

R526 111-1521-91 1/4WS 1.5kΩ

R527 117-1021-10 1/10W 1kΩ

R528 117-1031-10 1/10W 10kΩ

R529 111-1091-91 1/4WS 1Ω

R530 111-1091-91 1/4WS 1Ω

R531 111-1091-91 1/4WS 1Ω

R532 117-4721-10 1/10W 4.7kΩ

R533 111-1821-91 1/4WS 1.8kΩ

R534 117-1031-10 1/10W 10kΩ

R535 117-1031-10 1/10W 10kΩ

R536 117-2231-10 1/10W 22kΩ(PU-

2294A/PU-2325A)

R537 117-1031-10 1/10W 10kΩ(PU-

2294A/PU-2325A)

R538 111-1210-81 1/2WS 120Ω

R539 111-1210-81 1/2WS 120Ω

R540 117-0000-00 1/10W 0ΩJW

R541 111-1001-81 1/2WS 10Ω

R542 117-0000-00 1/10W 0ΩJW

R543 111-4701-91 1/4WS 47Ω

R547 117-0000-00 1/10W 0ΩJW

R549 117-1021-10 1/10W 1kΩ

R550 117-1031-10 1/10W 10kΩ

R551 117-4721-10 1/10W 4.7kΩ

R552 117-1031-10 1/10W 10kΩ

R553 117-1021-10 1/10W 1kΩ

R554 117-1031-10 1/10W 10kΩ(PU-

2294A/PU-2325A)

R555 117-2231-10 1/10W 22kΩ

R556 117-1031-10 1/10W 10kΩ

R557 117-1021-10 1/10W 1kΩ

R558 117-0000-00 1/10W 0ΩJW

R601 117-1031-10 1/10W 10kΩ

R602 117-1031-10 1/10W 10kΩ

R701 117-0000-00 1/10W 0ΩJW

R801 117-4731-10 1/10W 47kΩ

R802 117-1041-10 1/10W 100kΩ

R803 117-1041-10 1/10W 100kΩ

R804 117-1041-10 1/10W 100kΩ

R805 117-4721-10 1/10W 4.7kΩ

R806 117-4721-10 1/10W 4.7kΩ

R808 117-0000-00 1/10W 0ΩJW

R809 117-0000-00 1/10W 0ΩJW

R810 117-0000-00 1/10W 0ΩJW

R811 117-0000-00 1/10W 0ΩJW

R814 117-0000-00 1/10W 0ΩJW

R816 117-1031-10 1/10W 10kΩ

R819 117-4721-10 1/10W 4.7kΩ

R820 117-1031-10 1/10W 10kΩ

R826 117-2241-10 1/10W 220kΩ

R827 117-1031-10 1/10W 10kΩ

R828 117-1031-10 1/10W 10kΩ

R829 117-1031-10 1/10W 10kΩ

R830 117-1021-10 1/10W 1kΩ

R831 117-1021-10 1/10W 1kΩ

R832 117-1021-10 1/10W 1kΩ

R834 117-0000-00 1/10W 0ΩJW

R836 117-1021-10 1/10W 1kΩ

R839 117-1031-10 1/10W 10kΩ

R841 117-4721-10 1/10W 4.7kΩ

R842 117-2241-10 1/10W 220kΩ

R843 117-1021-10 1/10W 1kΩ

R844 117-1021-10 1/10W 1kΩ

R845 117-1021-10 1/10W 1kΩ

R846 117-1021-10 1/10W 1kΩ

R847 117-1021-10 1/10W 1kΩ

R848 117-1011-10 1/10W 100Ω

R850 117-0000-00 1/10W 0ΩJW

R851 117-0000-00 1/10W 0ΩJW

SUP1 060-0122-20 DSP-141N-S00B

TH501 002-0222-00 PTH61G30BD

TH502 002-0304-00 33Ω

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarion Stereoanlage Handbücher

Clarion

Clarion CM16-011205 Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken

LG CM3330B Bedienungsanleitung

Sony

Sony SS-CEP50 Bedienungsanleitung

Cetacea Sound

Cetacea Sound CVS-II Bedienungsanleitung

Aiwa

Aiwa XR-H66MD Bedienungsanleitung

Denon

Denon UCD-250 Bedienungsanleitung

Sanyo

Sanyo DC-MX41i Bedienungsanleitung

Sharp

Sharp CD-ES600V Bedienungsanleitung

Exibel

Exibel BDX600-UK Bedienungsanleitung

Sanyo

Sanyo DC-F320 Bedienungsanleitung

Philips

Philips FWM583X Bedienungsanleitung

Sharp

Sharp CD-C462 Bedienungsanleitung

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Bedienungsanleitung

Aiwa

Aiwa XR-EM70 Bedienungsanleitung

Cyrus

Cyrus Lyric Bedienungsanleitung

Philips

Philips MCM159/98 Bedienungsanleitung

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Bedienungsanleitung

RCA

RCA RS3965SB Bedienungsanleitung

Sharp

Sharp XL-UH240 Bedienungsanleitung