Clarity Walker W-1000 Bedienungsanleitung

Clarity®

The telephone that hears what you’ve been missing.

W-1000

User Guide

W1000_User_Guide 11/15/99, 9:37 PM1

SAFETY INSTRUCTIONS

INSTALLATION

FEATURES:

• Clarity Control®

• RingerVolume Control

• Visual Ringer

• Ringer Pitch Control

• Tone / Pulse Selection

• Last Number Redial

• Flash

• Hold

• Programmable Memory

• Cascade Dialing

OPERATION:

• To Place or Receive a Call

• Programming Emergency Numbers

• Programming Frequently-Dialed Numbers

• Cascade Dialing

CARE

TROUBLE-SHOOTING GUIDE

FCC REQUIREMENTS

LIMITEDWARRANTY

WALKERWARRANTY SERVICE

Table of Contents

W1000_User_Guide 11/15/99, 9:37 PM2

Page 3

W-1000

Read and Understand

All Instructions

Important Safety

Instructions

1.Never install telephone wiring

during a lightning storm.

2. Never install telephone jacks in wet

locations unless the jack is specifically

designed for wet locations.

3. Never touch uninsulated telephone

wires or terminals unless the line has

been disconnected at the network

interface.

4. Use caution when installing or

modifying telephone lines.

• Do not place this product on an

unstable cart,stand or table.The

product may fall,causing serious damage

to the product.

When using your telephone equipment,

basic safety precautions should always

be followed to reduce the risk of fire,

electric shock and injury to persons,

including the following:

• Slots and openings in the cabinet and

the back or bottom are provided for

ventilation,to protect it from

overheating,these openings must not be

blocked or covered.The openings

should never be blocked by placing the

product on the bed,sofa,rug,or other

similar surface.This product should

never be placed near or over a radiator

or heat register.This product should not

be placed in a built-in installation unless

proper ventilation is provided.

• Read and understand all instructions.

• Follow all warnings and instructions

marked on the product.

• Unplug this product from the wall

outlet before cleaning.Do not use liquid

cleaners or aerosol cleaners.Use a

damp cloth for cleaning.

• Do not use this product near water,

for example,near a bath tub,wash bowl,

kitchen sink,or laundry tub,in a wet

basement,or near a swimming pool.

• Do not allow anything to rest on the

power cord.Do not locate this product

where the cord will be abused by

persons walking on it.

Safety Instructions

SAVE THESE INSTRUCTIONS

W1000_User_Guide 11/15/99, 9:37 PM3

W-1000

Page 4

Safety Instructions

Continued

• Never push objects of any kind into

this product through cabinet slots as

they may touch dangerous voltage

points or short out parts that could

result in a risk of fire or electric shock.

Never spill liquid of any kind on the

product.

• To reduce the risk of electric shock,do

not disassemble this product,but take it

to a qualified serviceman when some

service or repair work is required.

Opening or removing covers may

expose you to dangerous voltages or

other risks.Incorrect reassembly can

cause electric shock when the appliance

is subsequently used.

SAVE THESE INSTRUCTIONS

C. If the product has been exposed to

rain or water.

D. If the product does not operate

normally by following the operating

instructions. Adjust only those controls

that are covered by the operating

instructions because improper

adjustment of other controls may result

in damage and will often require

extensive work by a qualified technician

to restore the product to normal

operation.

E. If the product has been dropped or

the cabinet has been damaged.

F. If the product exhibits a distinct

change in performance.

• Do not use this telephone to report a

gas leak in the vicinity of the leak.

• Unplug this product from the wall

outlet and refer servicing to qualified

service personnel under the following

conditions:

A. When the power supply cord or plug

is damaged or frayed.

B. If liquid has been spilled into the

product.

• Avoid using a telephone (other than a

cordless type) during an electrical storm.

There may be a remote risk of electric

shock from lightning.

W1000_User_Guide 11/15/99, 9:37 PM4

Page 5W-1000

The following items are included as part of the CS-03 Requirements.

The Load Number of the equipment is 20.

The standard connecting arrangement code for the equipment is CA11A.

NOTICE:The Canadian Department of Communications label identifies certified

equipment.This certification means that the equipment meets certain telecommunications

network protective operational and safety requirements.The Department does not

guarantee that the equipment will operate to the user’s satisfaction.

Before installing this equipment,users should ensure that it is permissible to be connected

to the facilities of the local telecommunications company.The equipment must also be

installed using an acceptable method of connection.In some cases,the company’s inside

wiring associated with a single line individual service may be extended by means of a

certified connector assembly (telephone extension cord).The customer should be aware

that compliance with the above conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance

facility designated by the supplier.Any repairs or alterations made by the user to this

equipment,or equipment malfunctions,may give the telecommunications company cause to

request the user disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the

power utility,telephone lines and internal metallic water pipe system,if present,are

connected together.This precaution may be particularly important in rural areas.

Caution:Users should not attempt to make such connections themselves,but should

contact the appropriate electric inspection authority,or electrician,as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of total

load to be connected to a telephone loop which is used by the device to prevent

overloading.The termination on a loop may consist of any combination of devices subject

only to the requirement that the total of the load numbers of all the devices does not

exceed 100.

Safety Instructions

Continued

SAVE THESE INSTRUCTIONS

W1000_User_Guide 11/15/99, 9:37 PM5

W-1000

Page 6

Inside you will find the following

items:

A. Handset

B. Handset Line Cord (Coiled,10 ft.)

C. Base Unit

D. Phone Line Cord (long,flat)

E. Desk/Wall-Mounting Bracket

F. This User’s Guide

• ModularWall Jack,or

• RJ-11C Modular JackAdapter (if you

have an older 4-prong jack)

Unpacking the Walker Clarity®

to exchange this unit for a factory-fresh

replacement.In addition to the items

listed above,you will need one of the

following to complete installation of this

unit:

RJ-11C

Carefully remove all of the contents

from the package.If there is any visible

damage,or any of the contents are

missing, do not attempt to operate this

equipment. Please call 1-800-552-3368

Clarity®

W-1000

User Guide

W1000_User_Guide 11/15/99, 9:37 PM6

Page 7

W-1000

Note:If you are

plugging the phone into

an older 4-prong jack,

use an RJ11C adapter

Select a Location:

Connecting the Clarity

Phone:

Warning:Toprevent

electrical shock,always

remove the telephone

line cord from the wall

jack before removing

the cord from the

telephone.Never leave

the line cord connected

to the wall jack if it is

not also connected to

the telephone.

• The unit should be located near a wall

jack for easy installation.

• The unit should be located in an area

where it is easy to see the lighted ringer.

• The unit can be used as a desk top

phone or a wall mount phone.

Avoid placing the unit

where it will be exposed

to excessive heat or

humidity.

To install as a Desk Unit:

• Plug one end of the telephone line

cord (long,flat) into the back of the

Walker Clarity.

• Plug the other end of the telephone

line cord into the wall jack.

• Plug one end of the handset cord

(coiled) into the bottom of the handset.

• Plug the other end of the handset cord

into the jack located on the left edge of

theWalker Clarity.

• Place the handset in the cradle of the

Walker Clarity.

Installation

Coiled

Cord

Here

Flat

Cord

Here

RJ-11C

W1000_User_Guide 11/15/99, 9:37 PM7

W-1000

Page 8

Note:If the wall-mounting bracket is

already placed in the desk mount position,

remove it by pressing the tabs and turning

it 180°per the key shown for the wall-

mount.

Walker Clarity comes assembled with

mounting bracket attached in desk

mount position.For wall mounting

simply remove bracket,rotate 180°

and reattach as shown.

To Install As a Wall Unit:

Important: A modular wall jack with

raised mounting pins is required for

installation as aWall Unit.

Desk

Mount

key

Wall

Mount

Key

Installation

Continued

• Attach the wall-mounting bracket to

the bottom of theWalker Clarity.It

snaps into place.The cord should run

underneath the wall mounting bracket.

• Plug one end of the telephone line

cord (long,flat) into the back of the

Walker Clarity.

• Plug the other end of the telephone

line cord into the wall jack with raised

mounting pins.You can store excess line

cord inside the wall mounting bracket.

Back of

Phone

Wall

Mount

Bracket

W1000_User_Guide 11/15/99, 9:38 PM8

Page 9W-1000

• Plug one end of the handset cord

(coiled) into the bottom of the handset.

• Plug the other end of the handset cord

into the jack located on the lower left

edge of theWalker Clarity.

• Place the handset in the cradle of the

Walker Clarity.The special tabs will hold

it in place.

Warning:To prevent electrical shock,

always remove the telephone line cord from

the wall jack before removing the cord from

the telephone.Never leave the line cord

connected to the wall jack if it is not also

connected to the telephone.

• Hold theWalker Clarity

so that the holes on the

mounting bracket line up

with the raised mounting pins on the

modular wall jack.Once the holes are

lined up,push the phone in towards the

wall jack and then slide the phone

downward until it is securely seated on

the wall jack.

Switch

Tabs

Installation

Continued

Walker Clarity® Features

Clarity Power Control®

The Clarity Power Control allows you

to control the clarity of your phone

conversations.It will let you hear clearly

phone calls that are normally difficult to

understand.The amplification will be

YourWalker Clarity is packed with

features that will help you improve

your communications over the

telephone.

Clarity

Power

Control

increased by more than 20 decibels (10

times) and the frequency band from

2000 to 3000Hz will be specially

enhanced to improve the clarity of your

call.

W1000_User_Guide 11/15/99, 9:38 PM9

W-1000

Page 10

Important: Reset the Clarity Power

Control to zero after every call to protect

other users of the telephone.A high setting

on this control may be unpleasant to

another user;caution should be taken to

reset it after every use.In addition,the high

performance of this Clarity Power Control

may cause the handset to“Squeal”or

produce feedback if the handset is set

down on a hard surface during the course

of a phone call.

Features

Continued

To Increase Clarity Power:

Slide the button marked Clarity Power

toward the right.

Slide the button toward the left.The

extreme left is the level of a normal

telephone conversation.

To Decrease Clarity Power:

9. 1Touch Programmable 10

Number Memory

10. Braille Dot on #5 Key

11. Flash Button

12. Hold Button

13. Hold Indicator

14. Clarity On/Off Button

15. Sound Level Indicator

1. Clarity Power Control®

2. RingerVolume Control

3. Visual Ringer

4. Ringer Pitch Control

5.Tone/Pulse Selector

6. Last Number Redial

7.Program Button

8.Three Emergency Numbers

* * * * * *

W1000_User_Guide 11/15/99, 9:38 PM10

Andere Handbücher für Walker W-1000

Inhaltsverzeichnis

Andere Clarity Telefon Handbücher

Clarity

Clarity Professional C4230 Bedienungsanleitung

Clarity

Clarity Walker W-1000 Bedienungsanleitung

Clarity

Clarity XL50 Bedienungsanleitung

Clarity

Clarity VCO Bedienungsanleitung

Clarity

Clarity Ensemble Bedienungsanleitung

Clarity

Clarity Alto Bedienungsanleitung

Clarity

Clarity XLC2 Bedienungsanleitung

Clarity

Clarity XL50 Bedienungsanleitung

Clarity

Clarity RC200 Bedienungsanleitung

Clarity

Clarity Professional C4205 Bedienungsanleitung

Clarity

Clarity XLC 3.4 Bedienungsanleitung

Clarity

Clarity Fortissimo Bedienungsanleitung

Clarity

Clarity XLC7BT Bedienungsanleitung

Clarity

Clarity 4020 Bedienungsanleitung

Clarity

Clarity Professional C2210 Bedienungsanleitung

Clarity

Clarity Professional C2210 Bedienungsanleitung

Clarity

Clarity BT914HS Bedienungsanleitung

Clarity

Clarity XLC2 Bedienungsanleitung

Clarity

Clarity XLC2+ Bedienungsanleitung

Clarity

Clarity C600 Bedienungsanleitung

Clarity

Clarity XL40D Bedienungsanleitung

Clarity

Clarity CE225 Bedienungsanleitung

Clarity

Clarity C35 Bedienungsanleitung

Clarity

Clarity Telephone Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung