Clarke CHT746 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0913

TELESCOPIC SPRING COMPRESSOR

MODEL NO: CHT746

PART NO: 1801746

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Telescopic Spring Compressor. Designed

for use on wishbone suspension using access points in the rear suspension arm.

features two pairs of carefully shaped yokes that prevent the coil spring from

bowing

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you can look forward to your

purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

WHAT IS SUPPLIED

Contact your Clarke dealer if any items are missing or damaged.

TECHNICAL SPECIFICATION

• 1 x drive handle • 2 pairs of compression yokes

Maximum Spring Load 1250 kg

Size/Suitability Ø 80-135 mm

Opening Range 115 - 300 mm

Weight 6.5 kg

Drive 19 mm Hex

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INSTRUCTIONS

•DO NOT operate the spring compressor if parts are damaged or

missing as this can cause failure or injury.

•DO NOT force the spring compressor to achieve a task it was not

designed to perform.

• DO NOT USE AIR TOOLS TO ADJUST THE SPRING COMPRESSOR.

•DO NOT allow untrained persons to use the spring compressor.

• Familiarise yourself with the applications, limitations and potential

hazards of the spring compressor.

• Maintain the spring compressor in good condition. Replace or repair

damaged parts. Use genuine parts only. Unauthorised parts may be

dangerous and will invalidate the warranty.

• Keep the work area clean, uncluttered and ensure there is adequate

lighting.

• Keep hands and body clear of the spring when operating the spring

compressor.

• Maintain correct balance and footing. Ensure the floor is not slippery

and wear non-slip shoes.

• Remove ill fitting clothes. Remove ties, watches, rings, other loose

jewellery. Contain and/or tie back long hair.

• Wear appropriate protective clothing.

• When not in use, clean and store the spring compressor in a safe, dry,

childproof location.

• Do not exceed the maximum capacity of this spring compressor

(1250 kg), if in doubt contact the vehicle manufacturer.

WARNING: ENSURE HEALTH & SAFETY, LOCAL AUTHORITY, AND

GENERAL WORKSHOP PRACTICE REGULATIONS ARE

ADHERED TO WHEN USING THIS EQUIPMENT.

WARNING: WEAR APPROVED SAFETY EYE PROTECTION (STANDARD

SPECTACLES ARE NOT ADEQUATE).

WARNING: DO NOT COMPRESS THE SPRING TO AN EXTENT WHERE THE

COIL WINDINGS OR YOKES TOUCH.

WARNING: MEASURE THE OUTSIDE DIAMETER OF THE SPRING TO BE

COMPRESSED AND SELECT THE CORRECT SET OF YOKES TO

FIT THE SPRING.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INSTRUCTIONS FOR USE

IMPORTANT: Do not use the coil spring compressor fully extended, but

adjusted to a length of approx. 200 mm. This will allow adequate travel to

expand and compress the spring.

1. Raise the vehicle to allow access to the spring.

• Make sure that the vehicle is safely and correctly supported.

2. Put the yoke (A) into the lower

part of the spring windings.

3. Insert yoke (B) into the upper part

of the spring windings.

• Make sure that the spring

windings sit between the inner

and outer rims of the yoke.

4. Insert the body of the spring

compressor up through the spring.

• The hexagonal drive nut must

be facing downwards.

5. Guide the compressor through

the lower yoke (A) and up into the

upper yoke (B),

6. When the compressor has passed

through the upper yoke turn the

body through approx 50° so it

locates in the locking grooves on

the yoke as shown.

• Make sure that the spring is

correctly placed within both

yokes and yokes are correctly

aligned with the compressor

body.

WARNING: MEASURE THE OUTER DIAMETER OF THE SPRING TO BE

COMPRESSED AND SELECT THE CORRECT SET OF YOKES.

WARNING: ENSURE THAT THE COIL SPRING TO BE COMPRESSED IS FREE

FROM DIRT AND GREASE WHERE THE YOKES WILL BE IN CONTACT WITH IT

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

7. Use a 19mm hex socket to turn the hexagonal drive nut until the yokes are

firmly in contact with the spring.

8. Now continue to compress the spring.

9. Remove the spring and compressor assembly from the vehicle as soon as

you have attained sufficient compression.

10. With the spring supported turn the hexagonal drive nut in the opposite

direction and remove the compressor and yokes from the spring.

11. To re-mount the spring, reverse the procedure.

WARNING: AIR TOOLS MUST NOT BE USED TO ADJUST THE SPRING

COMPRESSOR. USE OF AIR TOOLS WILL INVALIDATE THE WARRANTY.

WARNING: DO NOT ALLOW THE SPRING WINDINGS TO TOUCH. DO NOT

ALLOW THE COMPRESSOR TO REACH THE LIMIT OF ITS TRAVEL IN EITHER

DIRECTION.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTAINING THE SPRING COMPRESSOR

• Before each use check the compressor to ensure it is not damaged

or worn.

• If any damage is suspected, do not use the unit, but contact your

local Clarke Dealer who will be able to advise you regarding repair

and spare parts.

• Grease the compressor spindle as necessary to inhibit corrosion.

• Keep the compressor clean, and when not in use, store in a safe,

dry, location.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ALSO AVAILABLE FROM YOUR CLARKE DEALER

CHT695 OIL FILTER CAP WRENCH SET CHT701 12 PIECE OIL DRAIN PLUG

KEY SET

• Can withstand up to 85lb ft torque

• Oxide finish for rust protection

• Can be used with 3/8” & 1/2”

square drive wrenches

• Kit includes 14 wrenches, adaptor

and tough carry case

• 3/8" square drive carbon steel

tommy bar

• 7 Hex key drives 3/8", 8, 9, 10, 12, 14

& 17mm

• 4 Square key drives 3/8", 8, 11 &

13mm

CHT698 46 PIECE HARMONIC

BALANCE PULLER

CHT658 BRAKE CALIPER WIND BACK

TOOL SET

• Removes flywheels and

pulleys 36 to 95mm diameter

• Solid yoke designed for 2 or 3

point fixing

• 5" pressure screw

• Left & right hand

threaded bolt

assemblies

•Rewindtoolsand

reaction plate

• 15 adaptor plates to

suit a range of

vehicles

QR CODE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Luftkompressor Handbücher

Clarke

Clarke 6240056 Installations- und Betriebshandbuch

Clarke

Clarke RANGER 30 air Installations- und Betriebshandbuch

Clarke

Clarke Hunter 25 Bedienungsanleitung

Clarke

Clarke PP10ND Installations- und Betriebshandbuch

Clarke

Clarke AIRMASTER 14/150 Bedienungsanleitung

Clarke

Clarke BANDIT IV Bedienungsanleitung

Clarke

Clarke SHHHAIR MAX 50/150 Bedienungsanleitung

Clarke

Clarke CHAMP Installations- und Betriebshandbuch

Clarke

Clarke BANDIT Bedienungsanleitung

Clarke

Clarke RANGER 54 Bedienungsanleitung

Clarke

Clarke SHHH 2 Installations- und Betriebshandbuch

Clarke

Clarke RANGER 8/25 Bedienungsanleitung

Clarke

Clarke SHHHAIR 50/24 Bedienungsanleitung

Clarke

Clarke JUMBO Bedienungsanleitung

Clarke

Clarke ZX 500 Fehlerbehebungshandbuch

Clarke

Clarke CSS1 Bedienungsanleitung

Clarke

Clarke Warrior 55 Bedienungsanleitung

Clarke

Clarke BOXER II 14/50P Bedienungsanleitung

Clarke

Clarke SE Series Installations- und Betriebshandbuch

Clarke

Clarke RANGER 6/240 Bedienungsanleitung

Clarke

Clarke Air SP15ND Installations- und Betriebshandbuch

Clarke

Clarke VE15C150 Bedienungsanleitung

Clarke

Clarke SHHHAIR MAX 50/350 Bedienungsanleitung

Clarke

Clarke BOXER 100 Bedienungsanleitung

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung