Clarke Devil 3000 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC03/23

PROPANE GAS HEATER

MODEL NO: DEVIL 3000

PART NO: 6920027

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product. Before attempting to use this

product, please read this manual thoroughly and follow the instructions

carefully.

FUNCTION AND OPERATING PARAMETERS

This is a forced air heater meaning that a blower or fan pushes the air through

the heater. Proper combustion depends upon the air flow.

Therefore, the heater must not be modified or operated with parts removed or

missing. Likewise, safety systems must not be circumvented or modified in

order to operate the heater.

This heater is intended for drying and the warming of commercial/industrial

buildings where adequate ventilation is provided.

This heater is not intended;

• to be used for domestic use or for the heating of habitable areas.

• to be used to reach and maintain a certain level of human thermal

comfort within an enclosed space in which the heater is situated.

• be used in enclosed areas with restricted ventilation.

• for use in areas with high levels of fluctuating drafts.

• for warming animals or livestock.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INFORMATION

Signs of Carbon Monoxide poisoning are headaches, dizziness and/or nausea.

Should anyone show these signs, they must GET FRESH AIR IMMEDIATELY. Turn

off the heater and have it serviced before using again.

Pregnant women, persons with a heart or lung condition, anaemia or under

the influence of alcohol, or those at high altitude, are more likely to be

effected by Carbon Monoxide.

Read, and make sure you fully understand the following precautions and the

hazards associated with this type of heater.

Use ONLY liquid propane gas with this heater.

Ensure the propane gas bottle, gas hose and electric cable, are positioned

behind the unit, well away from the heat.

Ensure gas hose and regulator connections are gas-tight and the hose is not

kinked.

NEVER use the heater where flammable vapours or if a high dust content is

present in the air.

ONLY use with the voltage specified and ensure the heater is properly

earthed.

Use only in well ventilated areas. Provide ventilation of at least 3 square feet of

fresh air for every 100,000 BTU/hr of rating.

ALWAYS allow the working clearances around the heater as stated on page 5.

Keep the heater as far as practical from propane bottles and never point the

heater directly at any propane bottle.

Stand the heater on a stable, level surface whilst hot or operating. If the

heater should overturn, a fire could occur.

Keep children and animals away from heater at all times.

Use heater in accordance with all fire regulations.

NEVER use heater for domestic heating in living or sleeping areas.

NEVER leave a heater plugged in without adult supervision if children or

animals are likely to be present.

WARNING: LACK OF VENTILATION CAN CAUSE CARBON MONOXIDE

POISONING.

WARNING: CARBON MONOXIDE POISONING CAN KILL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

NEVER move, handle, replenish the gas supply or service the heater when it is

hot, operating or plugged in.

NEVER attach the heater to any duct work, or impede air flow into or out of

the heater.

Disconnect the heater from the power supply when not in use, especially at

night or otherwise unattended.

Use ONLY the factory pre-set regulator supplied.

If the heater works for long periods at maximum capacity, be aware that it is

possible for ice to form on the gas bottle due to excessive evaporation.

NEVER direct hot air towards the bottle in order to de-ice.

NEVER use in wet areas, basements or below ground level. Propane gas is

heavier than air and will sink to the lowest possible level.

ALWAYS ensure the heater is correctly maintained in accordance with this

manual.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

MINIMUM FRESH AIR OPENING REQUIREMENTS

• Minimum ventilation: 3.5 ft2

• DO NOT use in un-ventilated areas.

• The flow of combustion and ventilation air must not be obstructed.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MINIMUM CLEARANCES FROM COMBUSTIBLES

RISKS OF CARBON MONOXIDE POISONING

Even though this heater operates very close to 100 percent combustion

efficiency, it still produces small amounts of carbon monoxide.

• Carbon Monoxide (CO) is toxic.

• Pregnant women, persons with a heart or lung condition, anaemia

or under the influence of alcohol, or those at high altitude, are more

likely to be effected by Carbon Monoxide.

• CO can build up in a confined space and failure to provide

adequate ventilation can be fatal.

The early symptoms of asphyxiation caused by inadequate ventilation are:

Should anyone show these symptoms, they must GET FRESH AIR IMMEDIATELY.

Turn off the heater and have it serviced before using again.

Be sure to follow all the warnings in this manual.

WE RECOMMEND THE USE OF A CARBON MONOXIDE

DETECTOR

Outlet 8 Ft (2400mm) Top 3 Ft (900mm)

Sides 2 Ft (600mm) Rear 2 Ft (600mm)

•headache

•dizziness

• nausea

• dry mouth or sore throat

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved BS1363 plug fitted with a BS1362 13 amp fuse.

If the plug has to be changed because of damage, it must be removed and a

replacement fitted, following the wiring instructions shown below. The old plug

must be discarded safely, as insertion into a power socket could cause an

electrical hazard.

• The BLUE wire must be

connected to the

terminal marked N or

coloured black.

• The BROWN wire must

be connected to the

terminal marked L or

coloured red.

• The YELLOW AND

GREEN wire must be

connected to the

terminal marked E

or or coloured green.

We strongly recommend that this machine is connected to the mains supply

through a Residual Current Device (RCD)

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: WIRES IN THE MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN/YELLOW = EARTH, BLUE = NEUTRAL, BROWN = LIVE.

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PROPANE GAS SUPPLY

This portable, direct-fired gas heater is designed to give safe, efficient and

reliable operation, and is for use with propane gas only.

As with all mechanical equipment, optimum performance will only be

achieved if the correct operation and servicing procedures are followed.

In order to reduce the risk of icing up

when operating for long periods at

maximum capacity, you should use a

larger capacity gas bottle, or two/

three bottles in parallel as shown in the

diagram.

Ensure the Propane gas bottle, gas

hose and electric cable, are

positioned behind the unit, away from

the heat.

IN THE EVENT OF A GAS LEAK

1. Extinguish all smoking materials and other open flames.

2. Do NOT operate electric switches or light matches.

3. Close all supply valves on gas tank or cylinder.

4. Do NOT use your phone. USE a neighbour's phone or your mobile phone

from outside the building or wherever you detected the gas leak to call the

fire service.

5. Immediately get everyone out of the building or area.

6. Do NOT re-enter the building, or area until a trained service person or the

fire service advises it is safe to return.

WARNING: THE FITTING AND CHANGING OF THE GAS CYLINDERS MUST BE

CARRIED OUT IN A FLAME FREE ATMOSPHERE.

WARNING: YOU SHOULD ONLY USE PROPANE GAS CYLINDERS AVAILABLE

FROM BUILDERS MERCHANTS OR GAS SUPPLIERS.

WARNING: PROPANE GAS CYLINDERS MUST BE USED AND STORED IN

ACCORDANCE WITH THE ‘HIGHLY FLAMMABLE LIQUIDS AND LIQUEFIED

PETROLEUM GASES REGULATIONS 1972’

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PREPARATION

ASSEMBLY

1. Check the heater for possible

shipping damage. If any is found

do not use the heater.

2. Stand the heater on end as shown,

on a soft surface to avoid

scratches. We recommend the

help of an assistant to lift and

steady the heater during assembly.

3. Attach the rubber feet onto the

bottom panel.

LOCATION

Position the heater at a safe distance from combustible materials. (see page 5

for distances)

This heater must not be placed on wooden floors or other combustible

materials.

When used, the heater should rest on suitable insulating material at least 1

inch thick and extending 1M (3 ft) or more beyond the heater in all directions.

SIZE AND CAPACITY OF PROPANE CYLINDERS

The chart shows the approximate size of the bottle required for these heaters.

To use the chart:

1. Select the lowest air temperature expected (at the bottom of the chart).

2. Move straight up to time of operation desired (left side).

3. Read the bottle size required

4. Always use full bottles with good air circulation and no frost on the

cylinders.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING THE GAS BOTTLE

1. Follow all of the “General Safety” precautions on pages 3/4.

2. Connect a POL (Prest-o-Lite) fitting on hose/regulator assembly to the

propane bottle(s).

• Turn the POL fitting anti-clockwise into the threads on the bottle

Tighten firmly using a wrench.

3. Connect the hose to the heater by rotating the hose fitting clockwise.

• Make sure that all gas connections are secure.

4. Open the gas valve and check all gas connections with a soap and water

solution. DO NOT USE A FLAME.

5. Connect the power cable to a 230V, 50Hz, mains socket.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATING INSTRUCTIONS

HEATER START UP

1. Make sure the power switch is in

the OFF (O) position.

2. Turn the thermostat to the highest

setting.

3. Connect the heater to a suitably

fused power supply.

4. Slowly turn on the cylinder gas

valve.

• If not opened slowly, the excess-

flow check valve on the propane tank will stop the gas flow. If this

happens close the propane supply valve and open again slowly.

5. Start the heater by setting the power switch to the “ON(I)” position. The

heater will ignite automatically.

6. Adjust the knob on the control panel to the desired burn rate.

7. Set the thermostat to the desired temperature. The heater will turn off and

on automatically as the air reaches the desired temperature.

HEATER SHUT DOWN

1. Securely close the valve on the propane cylinder.

2. Continue to operate the heater until all fuel in the hose has burned.

3. Set the power switch to the OFF (O) position.

4. Unplug the heater.

RESTART AFTER SAFETY SHUTDOWN

1. Securely close the valve on the propane cylinder.

2. Unplug heater.

3. Wait 5 minutes.

4. Restart, following the Heater Start Up procedure above.

WARNING: BEFORE STARTING THE HEATER, YOU MUST ENSURE THAT THE

MINIMUM VENTILATION REQUIREMENTS ARE OBSERVED TO AVOID THE

RISK OF CARBON MONOXIDE POISONING.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Gasheizung Handbücher

Clarke

Clarke Little Devil II (inc ss) Bedienungsanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Clarke

Clarke MGH2 Bedienungsanleitung

Clarke

Clarke DEVIL 4000 Bedienungsanleitung

Clarke

Clarke GRH35 Bedienungsanleitung

Clarke

Clarke GRH125 Installations- und Betriebshandbuch

Clarke

Clarke GRH35 Installations- und Betriebshandbuch

Clarke

Clarke 900DV Bedienungsanleitung

Clarke

Clarke 900DV Bedienungsanleitung

Clarke

Clarke Little Devil (inc ss) Installations- und Betriebshandbuch

Clarke

Clarke Little Devil ss Installations- und Betriebshandbuch

Clarke

Clarke MGH1 Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 4000 Bedienungsanleitung

Clarke

Clarke Little Devil Installations- und Betriebshandbuch

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Superior

Superior BGE18NR Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung