Clarke CCLH1 Betriebsanleitung

ASSEMBLY & USER

INSTRUCTIONS

GC0514

CHAINSAW LOG HORSE

MODEL NO: CCLH1

PART NO: 3402085

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Loghorse.

Before attempting to use this product, it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will ensure

the safety of yourself and that of others around you, and you can also look

forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

GENERAL SAFETY PRECAUTIONS

1. Always thoroughly familiarise yourself with this product & its operation, and

always read and understand the instructions and warnings in this manual

before using the equipment.

2. Ensure the log horse is located on firm level ground when in use.

3. Always locate the log horse in a position where it does not pose a hazard

to yourself or others in the vicinity when not in use.

4. Keep work area tidy and well lit. Cluttered or dark areas invite accidents.

5. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the logs and saw in unexpected situations.

6. Keep children and bystanders away while operating a chain saw.

Distractions can cause you to lose control.

7. Use appropriate protective clothing as directed in the operating

instructions for the chainsaw, including safety gloves and eye protection.d.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

CONTENTS

The CCLH1 Loghorse comprises the following components:

Item Description Item Description

1 Fixed Support Panel 7 Measuring Rod Mounting Bracket

2 Hinged Support Panel 8 Chainsaw Clamp

3 Short Leg 9 Clamp Mounting Bracket

4 Cross Member 10 Foot

5 Long Leg 11 Saw Guard

6 Measuring Rod (length stop) 12 Fixings Pack

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

THE FIXINGS PACK

The fixings pack (12) includes the following:

When unpacking, check for damage or omissions etc. Any found should be

reported to your CLARKE dealer where the product was originally purchased.

Do not discard the packaging until the product is assembled.

ASSEMBLY

1. Join the two short legs (3)

together with one of the cross

member (4) using the 35 mm bolts

& nuts as in Fig 1.

2. Ensure that the locking flanges are

on the outside of the assembly as

in Fig 2.

• Repeat with the two long legs (5)

and the second cross-member.

3. Bolt the feet (10) to each of the

legs using 4 x 40 mm bolts & nuts

as shown in Fig 1.

4. Join the tops of the two leg

assemblies together using 2 x 40

mm bolts and nuts.

• The legs should hinge freely when

assembled.

1 x Hand-knob 2 x Plastic End Caps

1 x Large Securing Bolt 8 x 35mm Bolts/Nuts

1 x R-clip 6 x 40mm Bolts/Nuts

6 x Socket (Allen) Headed Bolts 2 x 50mm Bolts/Nuts

1 x Allen Key 1 x 65mm Bolt/Nut

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

5. Secure the fixed support panel (1)

in place between the long legs

using 6 Allen headed bolts and

the socket wrench supplied as

shown in Fig 3.

6. Attach the hinged support panel

(2) to the long legs using the 2 x 50

mm bolts & nuts.

7. Insert the pivot clamp mounting

bracket (7) into the top of the

long leg as shown in Fig 4.

• Take note of the way it is facing in

the diagram.

8. Using the large securing bolt,

secure the measuring rod

mounting bracket (9) to the bolt

hole in the pivot clamp mounting

bracket as shown in Fig 4.

9. Slide the measuring rod (6), into the hole in the measuring rod mounting

bracket (9) and secure with the handknob as shown in Fig 4. Press the

rubber end caps into place at the ends of the rod.

NOTE: The measuring rod can be adjusted horizontally to allow each log

to be cut equally to the desired length.

10. Take your chainsaw and secure it

between the two solid blocks on

the inside faces of the chainsaw

clamp as shown in Fig 5.

• Make sure that the chainsaw is at

90 degrees to the assembly

before tightening the clamp bolts

to grip the chainsaw in place.

Take care that the clamp blocks

grip the chain bar centrally and

are clear of the moving chain.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

11. Attach the saw guard (11) to the

chainsaw clamp using the nut &

65mm bolt as shown in Fig 6. Do

not overtighten.

12. Once tightened, take the saw

and the clamp assembly together

and insert the pivot rod of the

clamp into the hole in the clamp

support. Secure in place with the

R-clip as shown in Fig 6.

13. Test the arc of travel to make sure that the chainsaw does not touch any

part of the log horse.

14. Adjust the height of the clamp

and measuring rod to suit the size

of the logs being cut as shown in

Fig 7.

NOTE: The chainsaw clamp support

can be adjusted vertically to

accommodate different

sized chain saws - the larger

and longer the saw, the

higher the pivot clamp

should be positioned.

15. Use the large securing bolt to

adjust the saw height, so that the

tip of your chainsaw ends just past the table and is able to cut completely

through the log.

The Log Horse is now ready for use.

SAFE OPERATION

The log horse should only be used on firm, level surfaces. It should not be used

for logs larger than those stated in the specification.

Chainsaws with a chain bar longer than 450 mm should not be used, since the

chain would protrude beyond the chain guard.

When using a chainsaw with the log horse it is essential that you follow all

safety guidelines in the instruction manual supplied with your chainsaw. You

should also follow any other appropriate health and safety regulations.

1. Ensure the nuts and bolts on the pivot clamp and guard are kept tight

before starting work.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]

2. Place the log on the log horse

and butt the end of the log up

against the measuring rod.

3. Hold the log down firmly with your

left hand, keeping your hand well

away from the cutting chain at all

times as shown in Fig 8.

• Allow the chainsaw to do the

work, do not force the chainsaw

through the log.

4. Detach the pivot clamp and

guard by removing the R-clip when using the log horse separately from the

chainsaw.

5. All moving / adjustable parts should be kept sufficiently lubricated to resist

corrosion. Store in a dry place not exposed to the weather.

6. When operating an electric chainsaw always use a residual current device

(RCD) to ensure it will cut out in the event of difficulties arising.

SPECIFICATIONS

Please note that the details and specifications contained herein, are correct at the time

of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice.

ENVIRONMENTAL PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All un-

wanted accessories & packaging should be sorted and taken to a recycling

centre for disposal in a manner which is compatible with the environment.

Feature Specification

Maximum Chain Bar length 450mm

Maximum Log Length 1800mm

Maximum Log Diameter 200mm

Maximum Log Weight 120kg

Product Weight 11.1kg

Product Dimensions (W x D x H) 1310 x 715 x 785mm

Product Footprint (L x W) 715 x 815mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Holzspalter Handbücher

Clarke

Clarke LOGBUSTER 5 Bedienungsanleitung

Clarke

Clarke LOGBUSTER 9 Bedienungsanleitung

Clarke

Clarke LOGBUSTER 6 Bedienungsanleitung

Clarke

Clarke LOGBUSTER M Bedienungsanleitung

Clarke

Clarke LOGBUSTER 8 Bedienungsanleitung

Clarke

Clarke LOGBUSTER 7 Bedienungsanleitung

Clarke

Clarke Log Buster 4 Bedienungsanleitung

Clarke

Clarke LOGBUSTER H4 Bedienungsanleitung

Clarke

Clarke LOGBUSTER 10 Bedienungsanleitung

Clarke

Clarke LOGBUSTER II Installations- und Betriebshandbuch

Clarke

Clarke Log Buster 3 Bedienungsanleitung

Clarke

Clarke LOGBUSTER V6 Bedienungsanleitung

Clarke

Clarke LOGBUSTER P8 Bedienungsanleitung

Beliebte Holzspalter Handbücher anderer Marken

Bell

Bell Pickpine VS S9 Gebrauchsanweisung

ATIKA

ATIKA ASP 5 N-UG Betriebsanleitung

Posch

Posch Schälprofi 500 Bedienungsanleitung

Champion

Champion 91520 Handbuch

Fieldmann

Fieldmann FZLS 1008V-E Bedienungsanleitung

Craftsman

Craftsman 247.28775 Bedienungsanleitung

Scheppach

Scheppach OX 3-1000 Montageanleitung

Swisher

Swisher 21200 Bedienungsanleitung

Elem Garden Technic

Elem Garden Technic FBHT65-22TCH Bedienungsanleitung

Champion Power Equipment

Champion Power Equipment 90720 Handbuch

Villager

Villager LSP 12 T Bedienungsanleitung

Boss Industrial

Boss Industrial ES5T20 Bedienungsanleitung

MTD

MTD 242-642A Bedienungsanleitung

Rok

Rok 150-51-50255 Bedienungsanleitung

Hakki Pilke

Hakki Pilke Raven Bedienungsanleitung

Swisher

Swisher LSRB11534 Bedienungsanleitung

Hyundai

Hyundai HYLS7TE Bedienungsanleitung

Scheppach

Scheppach HL1500M Benutzerhandbuch