Clarke SAM100B Kurzanleitung

ASSEMBLY & OPERATING INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0417

SWING ARM MAGNIFYING LAMP

MODEL NO: SAM100B

PART NO: 5460532

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing your CLARKE swing arm magnifying lamp, which is

ideal for fine detail assembly and repair work, stamp collectors, model makers,

jewellers, etc.

Before using this product, read this leaflet thoroughly, and follow the

instructions carefully. Although the product is robust it should nevertheless be

used with care and consideration, you can then look forward to it giving long

and reliable service.

Do not attempt to repair or modify this product or attempt any electrical

repair yourself. Consult a qualified electrician or the Clarke Service

Department on 020 8988 7400.

SPECIFICATIONS

Model Number SAM100B

Upper/lower arm length 500 mm

Weight 2.8 kg

Operating Temperature 0-55oC

Duty Cycle S1 (continuous)

Fuse Rating 3A

Power Supply 230V @50Hz 1ph

Insulation Class II

IP Rating IP20

Luminance 5000 lux @15 cm

Lumen output 400 @1 m

Life expectancy of tube 6000 hours

Efficiency Class A

Flouoresent Tube T9, 22W

Colour Temp 6400K

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

•T

he wire which is coloured Blue must be connected to the terminal

which is marked N or coloured black.

•The wire which is coloured Brown must be connected to the terminal

which is marked L. or coloured red

We strongly recommend that this machine is connected to the mains supply via a

Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

This symbol indicates that this is a Class II product, and does not

require an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY

BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE

Plug must be BS1363/A approved.

Always fit a 3 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY AND OPERATION

ASSEMBLY

Your lamp is supplied in three parts;-

• The lamp assembly with arms,

• The G- clamp,

• The holder.

Slide the G-clamp into the slot in the

side of the holder, then slide the lamp

assembly spigot into the holder.

SETTING UP

The G-clamp can be mounted on flat

surfaces and variations in position

can be accommodated by the

angulation of the lamp assembly.

The lamp may be rotated freely in the

holder and the arms set at any angle

by slackening the pinch bolts,

adjusting the angle and re-

tightening.

Do not over tighten the pinch bolts.

When they are correctly tightened, the lamp should be capable of

maintaining stability in any position.

MAINTENANCE

Clean the lens when required with liquid glass cleaner used sparingly and with

a soft dry cloth. Do not allow the fluoresent tube or electrical connections to

get wet.

IMPORTANT: Always switch the lamp

OFF and unplug from the power

supply before cleaning the lens.

The tube will need replacing after

6000 hours of use.

Pull the diffuser to unclip it from the

head. Pull the tube away from its

retaining clips before unplugging the

four-pin connector to release the old

tube. Replace in reverse order.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CARE & STORAGE

When not in use, switch off & unplug from the power supply.

This product should be stored in a secure, dry place, out of the reach of

children. DO NOT leave it exposed to the elements and avoid direct sunlight,

direct heat, rain/moisture etc.

Keep the external surfaces clean. Avoid impact damage & do not allow this

product to come into contact with abrasive or corrosive materials.

Do not use solvents, thinners or alcohol for cleaning, as these chemicals will

damage the finish. With the lamp unplugged from the power supply, use a dry

cloth to wipe over the lamp components.

Only use extension leads that are of an appropriate power rating and suitable

for the work environment. Inspect the extension lead regularly and replace if

damaged.

Only use parts and accessories recommended in this manual. Never use

unauthorised accessories or attachments which may result in personal injury or

damage to the product.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS

Item No Description Qty

1LensCover 1

2 Metal Head cover 1

3Lens(3D) 1

4 T9/22W Lamp Tube (Clarke Part No 5460533) 1

5 Diffuser 1

6 On/Off Switch 1

7 Ballast 1

8 Plastic Back Cover 1

9Screws 5

10 A 4 5- Bar Swing Arm Assembly 1

11 C1 Table Holder 1

12 BS Plug & power cable 1

13 Metal handle 1

14 G- clamp 1

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Vergrößerungsglas Handbücher

Clarke

Clarke SAM127 Kurzanleitung

Clarke

Clarke SAM170 Kurzanleitung

Beliebte Vergrößerungsglas Handbücher anderer Marken

HIMS

HIMS SenseView DUO Bedienungsanleitung

nedis

nedis MAGL12WWT Bedienungsanleitung

Ryobi

Ryobi RML18-0 Bedienungsanleitung

Eschenbach

Eschenbach Visolux Digital XL FHD Bedienungsanleitung

ENHANCED VISION

ENHANCED VISION Merlin Bedienungsanleitung

Ash Technologies

Ash Technologies Andromeda Bedienungsanleitung

Baum

Baum VisioBook Handbuch

HIMS

HIMS GoVision PRO Bedienungsanleitung

OPTRON

OPTRON i-Stick Bedienungsanleitung

Eschenbach

Eschenbach visolux DIGITAL HD Bedienungsanleitung

LS & S

LS & S 251107 Bedienungsanleitung

VisionAid

VisionAid HandyReader HD v2 Bedienungsanleitung

Carson

Carson SV-50 Bedienungsanleitung

MAGINON

MAGINON TL-70 Bedienungsanleitung

Optelec

Optelec Compact 7 HD Bedienungsanleitung

Optelec

Optelec ClearView GO Bedienungsanleitung

Carson

Carson Lighted MagniGrip MG-88 Bedienungsanleitung

VisionAid

VisionAid Helix HD Bedienungsanleitung