Clarke JSM400 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1020 - ISS 2

LITHIUM POLYMER JUMPSTARTER

MODEL NO: JSM400

PART NO: 6239015

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Please read this manual thoroughly and follow the instructions. In doing so you

will ensure the safety of yourself and that of others around you, and you can

look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All

tools, accessories and packaging should be sorted, taken to a

recycling centre and disposed of according to the laws governing

Waste Electrical and Electronic Equipment.

SPECIFICATIONS

Model Number JSM400

Battery Capacity 21 Ah

Jumpstart Output Current Starting 400A / Peak 800A

USB Output 5V @ 1A + 5V @ 2.1A

DC Output 19V @ 3A

Dimensions (L X W X H) 220 x 90 x 30 mm

Weight 1.37 kg

Engine Capacity Up to 6L Petrol - Up to 4L Diesel

Operating Temperature 0°C to 45°C

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. DO NOT leave the device exposed to the elements. Avoid direct sunlight,

direct heat, rain/moisture etc.

2. The device must only be used indoors or completely protected from the

rain. This also applies to any device being powered by the device.

3. DO NOT operate the device if any of the cables are damaged. Consult

your CLARKE dealer for repair or replacement of the parts.

4. DO NOT operate the device if the case is damaged. Consult your CLARKE

dealer or a qualified person for inspection and repair.

5. To prevent the battery from overheating and consequent damage, DO

NOT exceed our recommendations for the duration of jump starting.

6. The unit is NOT designed to be used as a replacement for a vehicle

battery.

7. NEVER allow the battery to become completely discharged.

8. NEVER jump start the engine whilst the unit is being charged.

9. NEVER attempt any repairs yourself. If you have a problem with the unit

contact your local CLARKE dealer.

10. ALWAYS keep your body and clothing dry. Never work in a damp area

without adequate insulation against electric shock.

11. ALWAYS store the device out of reach of children.

12. ALWAYS wear safety glasses when working with lead acid batteries.

13. If splashed by battery acid, immediately flush the area of the splash with

clean water. If a burning sensation is felt or any blistering occurs, seek

medical help.

14. If battery acid comes into contact with the eyes, flush the eyes with clean

water continuously and seek medical help.

15. ALWAYS ensure that there is air circulating around the unit when in use.

16. When not in use, store in a safe dry place.

WARNING: ALL LEAD ACID BATTERIES GENERATE HYDROGEN GAS

DURING NORMAL OPERATION. THIS PROCESS INCREASES DURING A

PERIOD OF RAPID DISCHARGE.

WARNING: HYDROGEN GAS AND BATTERY ACID (SULPHURIC ACID) CAN

BE EXPLOSIVE, CORROSIVE TO SKIN, EYES AND HAIR, DAMAGING TO

CLOTHING AND METALS, FLAMMABLE, POISONOUS TO BREATHE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

17. NEVER allow the jumpstart leads, to touch each other or to touch the

same metal object.

18. Ensure the vehicle battery posts and battery clamps are perfectly clean

before use.

19. Connect the red clamp to the unearthed battery terminal first, (this is

usually the positive (+ve) terminal and coloured RED); then connect the

black clamp to the earthed battery terminal, (this is usually the negative (-

ve) terminal and coloured BLACK).

20. ALWAYS wear suitable protective clothing and eye protection when

working with lead acid batteries.

21. NEVER allow the cables to become wrapped around the operator or any

other person.

22. Wipe the body of the unit clean using a soft damp cloth, DO NOT use

abrasives to clean this product.

ELECTRICAL CONNECTIONS

This device is supplied with a 13 amp, 230 volt (50Hz), charging adaptor for

connection to a standard, domestic electrical supply.

This appliance is of double insulated design. No earth conductor is provided.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

SAFETY SYMBOLS

Class II appliance

(charger)

Always read instructions

before use

Suitable for indoor use

only (refers to mains

adaptor only)

Subject to Waste Electri-

cal & Electronic Equip-

ment Directive

Live centre pin Wear Eye Protection

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Jumpstart Lead Socket 5 On/Off Button

2 USB Sockets 5V DC 6 Charger Input Socket

3 Worklight 7 19V DC Output Socket

4 Power Indicator Lights

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CHARGE THE POWER PACK

You can charge the power pack using:

• The 230V AC mains charger (A)

• The 12V DC cigar lighter (aux

power) adapter (B).

1. Switch the power pack off.

2. Plug the mains charger or cigar

lighter adapter into the charger

input socket

3. If you are using the cigar lighter

adapter, start the engine.

4. Connect the other end to either

the mains supply or cigar lighter

socket in the vehicle.

• The 5 power indicator lights on the top show the current charge level,

20%, 40%, 60%, 80% and 100%.

5. Disconnect the charger when all 5 power indicator lights are lit up.

TO GET THE MAXIMUM LIFE FROM THE BATTERY

• Charge the power pack before first use.

• Charge the power pack after each operation or a minimum of once

every 3 months.

• DO NOT leave the power pack in a state of discharge.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

WORK LIGHT

1. Push and hold the ON/OFF button

for 3 seconds to turn the work light

on.

2. Push the ON/OFF button again.

• The work light flashes on and

off.

3. Push the ON/OFF button again.

• The work light flashes with the

morse code SOS pattern.

4. Push the ON/OFF button again to turn the work light off.

USB POWER SUPPLY

• The top socket supplies a maximum of 1A at 5V.

• The lower socket supplies a maximum of 2.1A at 5V.

1. Put the USB cable into one of the

USB sockets.

2. Connect the other end of the

cable to your device.

3. Push the ON/OFF button to start

supplying power.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DC POWER SUPPLY

1. Insert the small fly lead into the

power pack.

2. Install the connector you need

onto the other end of the fly lead.

3. Insert the connector into the

device you want to power.

4. Push the ON/OFF button to start

supplying power.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

JUMP STARTING

NOTE: This device will not jumpstart a vehicle if the battery is very low or

completely flat.

CONNECTING THE SMART CABLE TO THE POWER PACK

1. When jumpstarting, a minimum of

3 of the power indicator lights

located on top of the device must

be lit. Recharge the device if

required.

2. Lift the rubber plug and insert the

blue EC5 connector of the smart

lead into the power pack.

• The red & green LEDs on the

smart lead flash alternately.

CONNECT THE JUMP START LEADS TO THE BATTERY

1. Connect the red clamp to the unearthed battery terminal first, (this is

usually the positive (+ve) terminal and coloured RED).

2. Connect the black clamp to the earthed battery terminal, (this is usually

the negative (-ve) terminal and coloured BLACK)

3. Once you have connected the leads you have 30 seconds to try and start

the vehicle, otherwise you will need to remove the leads and reattach

them.

WARNING: SOME VEHICLE ELECTRONIC EQUIPMENT MAY BE DAMAGED

BY JUMP STARTING. ALWAYS CHECK WITH THE VEHICLE HANDBOOK.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SMART CABLE STATUS LIGHTS

JUMPSTART THE VEHICLE

ALWAYS carry out the following preliminary checks:

• Switch off the vehicle ignition and ALL ancillary equipment (lighting,

radio etc.)

• Ensure the vehicle battery is rated at 12V and is not damaged in any

way.

• Ensure the area is well ventilated.

• Make sure that the device is at least 60% charged (3 power indicator

lights are lit).

NOTE: This device will not jumpstart a vehicle if the battery is very low or

completely flat.

1. Switch the ignition to ‘start’ for NO MORE than 6 seconds. If the engine does

not start within this time, SWITCH OFF the ignition and wait for at least 3

minutes before trying again.

2. Once the engine is running, disconnect the clamps within 30 seconds,

BLACK clamp FIRST, then disconnect the RED clamp.

3. Leave the vehicle engine running for a while to let the alternator recharge

the battery.

STATUS GREEN LED RED LED BEEPING

Detecting Flashing Flashing No

Low voltage Off Solid No

Ready to start Solid Off No

Short circuit Off Solid Beeping

Reverse polarity Off Solid Discontinuous

Beeping

Reverse charge Off Solid Slow Beeping

Over-heating Off Solid Fast Beeping

Over current Solid Solid

Timing protection (30 seconds) Solid Solid

CAUTION: MAKE SURE THAT THE POWER PACK IS AT LEAST 60% CHARGED

(3 POWER INDICATOR LIGHTS ARE LIT) BEFORE YOU ATTEMPT TO

JUMPSTART.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Power Pack Handbücher

Clarke

Clarke JSM200 Bedienungsanleitung

Beliebte Power Pack Handbücher anderer Marken

EcoFlow

EcoFlow Wave 2 Bedienungsanleitung

Schumacher

Schumacher DSR PRO Series Bedienungsanleitung

Draper

Draper 12V Power Packs Bedienungsanleitung

Haug

Haug Multistat Ex SDN Bedienungsanleitung

Intermatic

Intermatic IOS-PP24 Kurzanleitung

Makita

Makita PDC01 Bedienungsanleitung

Skiva

Skiva AC110 Bedienungsanleitung

Bluetti

Bluetti AC60P Bedienungsanleitung

Draper

Draper PP12VA Bedienungsanleitung

Goodsmann

Goodsmann 9920-0300-01 Bedienungsanleitung

Risen

Risen RSN-BX007 Bedienungsanleitung

Hama

Hama A4 Series Bedienungsanleitung

Graco

Graco GH 24X011 Stücklistenhandbuch

ring

ring TradeStart RPPS3000 Bedienungsanleitung

Bluetti

Bluetti AC500 Bedienungsanleitung

Hama

Hama 00187292 Bedienungsanleitung

HYCON

HYCON HPP09 Gebrauchsanweisung

Tycon Power Systems

Tycon Power Systems TP-PP120-INV Bedienungsanleitung