Clarke CAMTS Bedienungsanleitung

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]m

ADJUSTABLE MACHINE TOOL STAND

MODEL NUMBER: CAMTS

PART NUMBER: 6501610

INTRODUCTION

Thank you for purchasing this CLARKE Adjustable Machine Tool Stand.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing

so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please

keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the

purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

PART IDENTIFICATION

If any parts are missing or damaged, please contact the Clarke dealer where you purchased the tool stand.

NO DESCRIPTION QTY

1Legs 4

2 Foot 4

3Shelf 2

4 Short Shelf Support 2

5 Long Shelf Support 2

6 Short Spreader Bar 2

7 Long Spreader Bar 2

8TopPanel 2

FIXINGS SUPPLIED

Wood Screws 8

Washers 8

Bolts 24

Spring Washers 24

Nut 24

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or [email protected]m

ASSEMBLY

SPECIFICATIONS

1. Make up the front frame by connecting the

two legs, a long spreader bar, and the long

shelf support as shown, Fix them together

using the bolts, nuts and spring washers.

• The nut and spring washer should be on the

inside of the completed frame

• Do not fully tighten the nuts and bolts at this

stage.

2. Make up the rear frame in the same way.

3. Join the two frames using the two short shelf

supports and two short spreader bars, again

fixing them together using the bolts, nuts and

spring washers.

• The short spreader bars should be place on

the inside of the frame.

4. Place the two shelves into position.

5. Fit the feet to the end of each leg.

6. Place the the top panels on to the short

spreader bars as shown, set to the required

distance apart and fix in position using the

screws and washers supplied.

• The screws are inserted from below through

the short spreader bars into the top panels.

7. Tighten up all the nuts, bolts and screws. The tool

stand is now ready for use.

Model Number CAMTS

Maximum Load 226 kg

Weight (unpacked) 11.5 kg

Dimensions (L x W x H) 810 mm x 570 mm x 810 mm

Dieses Handbuch passt für folgende Modelle

Andere Clarke Zubehör für Elektrowerkzeuge Handbücher

Clarke

Clarke CRT1 Bedienungsanleitung

Clarke

Clarke CWTS1 Betriebsanleitung

Clarke

Clarke CPS85R Bedienungsanleitung

Clarke

Clarke 6460200 Bedienungsanleitung

Clarke

Clarke 6500232 Bedienungsanleitung

Clarke

Clarke CAT150 Gebrauchsanweisung

Clarke

Clarke CHT599 Bedienungsanleitung

Clarke

Clarke CHT622 Bedienungsanleitung

Beliebte Zubehör für Elektrowerkzeuge Handbücher anderer Marken

Bosch

Bosch OSC004 Bedienungsanleitung

Rockler

Rockler 57510 Bedienungsanleitung

Bosch

Bosch RA1054 Montageanleitung

Grizzly

Grizzly T10808 Bedienungsanleitung

Kitagawa

Kitagawa SC N Series Bedienungsanleitung

Wolfcraft

Wolfcraft FKS 145 Kurzanleitung

ADAMAS

ADAMAS B32 Bedienungsanleitung

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Bedienungsanleitung

Echo

Echo Speed-Feed Universal 400 LH/RH Bedienungsanleitung

SCHUNK

SCHUNK ROTA TB-TBS-EP Gebrauchsanweisung

Schmid

Schmid RAPID Secure XL Bedienungsanleitung

Drill Master

Drill Master 360X Bedienungsanleitung

Toro

Toro 138-5050 Bedienungsanleitung

jbc

jbc SF-SD Bedienungsanleitung

Bosch

Bosch GTA 3800 Professional Montageanleitung

RG AVAK

RG AVAK MaxDrill Series Bedienungsanleitung

infaco

infaco PW3 Bedienungsanleitung

Gloria

Gloria CUT & BRUSH Bedienungsanleitung