Clas Ohlson TC1840S Bedienungsanleitung

Model TC1840S

SVENSKANORSKSUOMI ENGLISH

Garden Trolley

Transportvagn

Transportvogn

Kuljetusvaunu

30-8355

www.clasohlson.com

Ver. 200710





ENGLISH

Gaden Trolley, No 30 - 8355, model TC1840S

Please read the entire instruction manual before using and save it for future use. We apologise for

any text or photo errors and any changes of technical data. If you have any questions concerning

technical problems please contact our Customer Service Department (see address on reverse.)

Parts list

No. Part Count

1. Deck 1

2. Side wall 2

3. Front wall 1

4. Rear wall 1

5. Wheel 4

6. Rear axel support 1

7. Rear axel bracket, left 1

8. Rear axel bracket, right 1

9. Front axel support 1

10. Centre bracket for front axel 1

11. Yoke (Load-bearing axle) 1

12. Bracket 1

13. Connector 1

14. Pulling handle 1

15. Pull rod 1

16. Cotter pin 8

17. Split pin 1

18. Locking lever ( pre-mounted ) 4

19. Washer 11

20. Lock nut 11

21. Spacer sleeve 4

22. Cap nut 4

23. Large washer 4

24. Bolt M8 x 20 for support bars 10

25. Bolt M8 x 80 for pull rod 1

26. Bolt M8 x 15 for steering mechanism 3

27. Bolt M8 x 17 for steering mechanism 1

28. Small washer 4

29. Small lock nut 4

30. Spring washer for wheels 4

31. Large washer for yoke 1

32. Pulling bolt 1

33. Small cotter pin 1

Safety concerns

Do not load trolley with more than 250 kg. Do not let children use trolley without supervision. The

trolley is not a toy! Distribute load evenly on the deck. Lower the side or rear wall when loading.

Limit tyre pressure to 2.2 bar.

Disposal

Follow local ordinances when disposing of this product. If you are unsure about how to dispose of

this product contact your municipality.



ENGLISH

Assembly instructions

Carefully take out all parts from packaging and lay them out on a flat and level surface.

Tools needed for assembly

Slotted screwdriver

2 medium sized adjustable spanners

Note

Do not completely tighten screws until the assembly is finished. For ease of assembly, we

recommend that you have an assistant.

Rear wheel-axle assembly

The following parts are required:

No. 5 Wheels

No. 6 Rear axel support

No. 7 Rear axel bracket, left

No. 8 Rear axel bracket, right

No. 21 Spacer sleeves

No. 22 Cap nuts

No. 23 Large washers

No. 30 Spring washers for wheels

1. Slide both left and right axle brackets

(parts 7 and 8) onto threaded ends of axel support (part 6).

2. Slide spacer sleeves (part 21) onto same threaded ends.

3. Slide wheels onto same threaded ends.

4. Secure wheels with large washers (part 23), spring washers (part 30) and finally cap nuts (part

22). Tighten cap nuts clockwise until wheels are firmly in place.



ENGLISH

Front wheel-axle assembly

The following parts are required:

No. 5 Wheel

No. 9 Front axel support

No. 10 Centre bracket for front axel

No. 11 Yoke

No. 12 Bracket

No. 17 Split pin

No. 21 Spacer sleeves for wheels

No. 22 Cap nuts

No. 23 Large washers

No. 26 Bolts M8 x 15 for steering mechanism

No. 27 Bolt M8 x 17 for steering mechanism

No. 28 Small washers

No. 29 Small lock nuts

No. 30 Spring washers for wheels

1. Attach bracket (part 12) to front axle support

(part 9) by putting two M8 x 15 bolts (part 26)

through top of bracket as well as axel support.

Secure bolts from below with small washer

(part 28) and small lock nut (part 29). Tighten

nut clockwise until parts are firmly in place.

2. Attach yoke (part 11) and centre bracket for

front axel (part 10) to front axle support (part

9) by putting an M8 x 17 bolt (part 27) through

hole in centre bracket (part 10), then through

second hole in yoke and finally through lower

hole in front axle support. Slide small washer

(part 28) onto bolt from below and secure

it with small lock nut (part 29). Tighten nut

clockwise until parts are firmly in place.

3. Attach yoke (part 11) to bracket (part

12) by putting an M8 x 15 bolt (part 26)

through first hole in yoke and then through

bracket. Secure bolt with small washer

(part 28) and lock nut (part 29). Tighten nut

clockwise until parts are firmly in place.



ENGLISH

 Attach top part of

yoke (part 11) to

stud located on

underside of front

axle support (part

9) by placing large

yoke washer (part

31) on stud and sliding

split pin (part 17) through

hole in stud. Note: Use a

slotted screwdriver to bend

apart legs of split pin in order

to secure it.

5. Slide spacer sleeves (part 21) onto

protruding threaded axles on front axle support

(part 9).

6. Slide wheels (part 5) onto axle.

7. Secure wheels with large washer (part 23), spring washer (part

30) and lastly with cap nut (part 22). Tighten cap nut until wheel is

firmly in place.

Assembly of deck

The following parts are required:

No. 1 Deck

No. 24 Bolts M8 x 20 for support bars

No. 20 Lock nuts

No. 19 Washers

No. 13 Connector

No. 14 Pulling handle

No. 15 Pull rod

No. 25 Bolt M8 x 80 for pull rod

No. 32 Pulling bolt

No. 33 Small cotter pin



ENGLISH

1. Turn deck (part 1) upside down. Attach rear wheel-axle assembly to deck by putting six M8

x 20 bolts (part 24) through deck support bars from underneath, and then through holes situ-

ated on left and right rear axle brackets (parts 7, 8) and rear axle support (part 6). Slide wash-

ers (part 19) onto bolts and secure with lock nuts (part 20). Tighten nuts clockwise until parts

are firmly in place.

2. Attach front wheel-axle assembly to bed (part 1) by putting another four M8 x 20 bolts (part

24) first through holes in deck support bars from underneath, and then through holes in front

axle support (part 9) and centre bracket (part 10). Slide washers (part 19) onto bolts and

secure with lock nuts (part 20).

3. Attach pulling rod (part 15) to yoke (part 11). Then attach pulling handle (part 14) to pulling

rod (part 15) if intended for use.



ENGLISH

A. Pulling with tractor

Attach connector (part 13) to pull rod (part 15) by simply sliding

pull rod into hole in connector. Align holes in pull rod with holes

in connector. Attach pull rod to yoke (part 11) by aligning the

holes and sliding bolt M8 x 80 (part 25) first through yoke, then

through connector and out through other side of yoke. Secure

with washer (part 19) and lock nut

(part 20).

Connect trolley to back of tractor or utility vehicle

with pulling bolt (part 32). Secure with cotter pin

(part 33).

B. Pulling by hand

Attach pull rod in the same manner as in instruction A above. Instead of connecting pull rod to

a tractor, you can attach pulling handle to pull rod with pulling bolt (part 32) and cotter pin (part

33). Slide pulling handle (part 14) into u-shaped end of pull rod (part 15). Align holes and insert

pulling bolt. Secure with cotter pin (part 33).



ENGLISH

Assembly of frame

The following parts are required:

No. 2 Side walls

No. 3 Front wall

No. 4 Rear wall

No. 16 Cotter pins

No. 18 Locking levers – pre-mounted on

front and rear walls

No. 19 Washers - on front and rear walls

No. 20 Lock nuts - on front and rear walls

Assembled deck

1. Fasten rear wall (part 4) to deck (part 1) by

sliding two cotter pins (part 16) through the

holes at bottom of rear wall and top of deck.

2. Fasten side walls (part 2) to deck (part 1)

by sliding another four cotter pins (part

16), two per side wall, through holes at

bottom of side walls and top of deck.

3. In order to secure rear wall (part 4) with

side walls (part 2), lift pre-mounted lock-

ing levers (part 18) on front and rear walls.

Then forcefully press each locking lever

downward and around the catch on end

of side wall.

4. Do the same for front wall

(part 3) using cotter pins (part

16) and two remaining locking

levers (part 18).



SVENSKA

Transportvagn, nr 30-8355, modell TC1840S







Leveransomfång

Nr. Beteckning Antal

1. Bädd 1

2. Sidopanel 2

3. Frontpanel 1

4. Bakpanel 1

5. Hjul 4

6. Bakaxelstöd 1

7. Bakaxelfäste vänster 1

8. Bakaxelfäste höger 1

9. Framaxelstöd 1

10. Mittfäste för framaxel 1

11. Ok (Bärande axel) 1

12. Länkfäste 1

13. Kopplingsdon 1

14. Handtag 1

15. Dragstång 1

16. Spärrstift 8

17. Saxsprint 1

18. Låsspak ( monterade ) 4

19. Brickor 11

20. Låsmuttrar 11

21. Distanshylsor 4

22. Kupolmuttrar 4

23. Stora brickor 4

24. kruvar M8 x 20 för kärrstöd 10

25. Skruv M8 x 80 för draghandtag 1

26. Skruv M8 x 15 ( styrbultar ) 3

27. Skruv M8 x 17 ( styrbult ) 1

28. Liten bricka 4

29. Små låsmuttrar 4

30. Fjäderbrickor för hjul 4

31. Stor bricka för ok 1

32. Dragbult 1

33. Liten låspinne 1

För säkerhets skull . . .

Belasta inte vagnen med mer än 250 kilo. Låt inte barn använda den utan uppsikt. Vagnen är

ingen leksak! Fördela lasten jämnt över bädden. Sänk gavel / sidopanel när du lastar på. Pumpa

inte i luft till mer än 2,2 bar.

Avfallshantering

När du ska göra dig av med produkten ska detta ske enligt lokala föreskrifter. Är du osäker på hur

du ska gå tillväga, kontakta din kommun.

Inhaltsverzeichnis

Sprachen:

Andere Clas Ohlson Rasen- und Gartengeräte Handbücher

Clas Ohlson

Clas Ohlson 31-1755 Bedienungsanleitung

Clas Ohlson

Clas Ohlson I571157C Bedienungsanleitung

Clas Ohlson

Clas Ohlson Bug Zapper Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-1756 Bedienungsanleitung

Clas Ohlson

Clas Ohlson SI-31 Bedienungsanleitung

Clas Ohlson

Clas Ohlson TC4215C Bedienungsanleitung

Clas Ohlson

Clas Ohlson ZK-7036 Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-9683 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung