Classic Exhibits Visionary DESIGNS MOD-1710 Handbuch

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT VIEW

TOP VIEW

= 1 sq foot

MOD-1710 Interactive Kiosk

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

CEI-110 Profile

Straight Bracket Assembly

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion, so that two of the

set screws are inside groove. Tighten two set screws

to secure.

3) Slide connecting extrusion over exposed ends of

bracket & connector. Tighten all remaining set screws

to secure extrusions.

2) Slide one V4 Connector into outer interior groove

of extrusion, so that one set screw is inside groove.

Tighten set screw.

TS RV 4

Bracket

Insert two-piece

bracket into the

interior center slot

of extrusion.

Slide V4 Connector

into front interior

groove.

Secure inserted half of

bracket & connector

using set screws.

Slide connecting

extrusion over

exposed ends

of bracket &

connector.

Completed

Assembly

Secure extrusion,

using remaining

set screws.

Set

Screws

Straight Connection

Corner Connection

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 2

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Assembly

CEI-110 Frame Assembly

CEI110 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab.Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Step 1 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

FRONT VIEW

Steps:

Refer to the CEI110 Frame Assembly general information page.

1) Assemble verticals [1,2] between horizontals [3,4], inserting Sintra blocker.

2) Connect power cords to Supernova lights as shown.

When assembled

Item

Qty.

Description

33”h CEI110 Vertical Extrusion

35.5”w CEI110 Horizontal Extrusion

Blocker

Transformer

Power

Female

Transformer

96W / 4 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 7 lights per Transformer

Light to Transformer Attachment

Counter Assembly

Step 2 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

1) Assemble lower horizontals [11,13,15,17,18,19] between verticals [5,6,7,8,9,10].

2) Slide Infills between verticals [5,10], [6,7], [7,8], [9,10].

3) Connect upper horizontals [12,14,16,20,21,22] between verticals [5,6,7,8,9,10],

securing infills.

4) Assemble horizontals [25,26] between verticals [23,24].

5) Connect horizontals [27,28], [29,30] between verticals [23,24] & verticals [8,9],

inserting Infills.

Item

Qty.

Description

36.098”h S44 Vertical Extrusion

44.5”h S44 Vertical Extrusion

31.846”w Z41 Horizontal Extrusion

6.591”w Z41 Horizontal Extrusion

11.112”w Z41 angled Extrusion

6.591”w Z41 Horizontal Extrusion

11.112”w Z41 angled Extrusion

4”w Z41 Horizontal Extrusion

20.224”w Z41 Horizontal Extrusion

4”w Z41 Horizontal Extrusion

20.224”w Z41 Horizontal Extrusion

4”w Z41 Horizontal Extrusion

41.325”h S44 Vertical Extrusion

20.224”w Z41 Horizontal Extrusion

8.189”w Z41 Horizontal Extrusion

Infill

When assembled

Counter Assembly (cont’d)

Step 3 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

Monitor

Mount

Monitor Mount

Panel

BACK VIEW

Steps:

1) Attach Door between verticals [23,24]. See Door Attachment detail.

2) Connect Monitor Mount to Monitor Mount Panel, using bolts & wing nuts.

3) Attach Monitor Mount Panel to horizontals [14,16], using bolts & V4 connectors.

See V4 Connectior detail.

Door

Hinge

Slide pin into

hinge attached

to vertical.

Slide door

hinge over pin.

Door Attachment

When assembled

Door

Item

Qty.

Description

Cabinet Door

35.5”w x 12.169 Monitor Mount Panel

Monitor Mount

V4 Connector

Slide V4 connector into

groove of extrusion &

secure with set screw.

Attach bolt to V4 connector.

set

screw

V4 Connector

23 24

Counter Assembly (cont’d)

Step 4 of 4

Order #XXXXX

Locked layer contains

placeholder marks.

*BACK VIEW

Steps:

1) Connect Counter Top to top of horizontals [26,28,30]. See Counter Top Attachment detail.

2) Connect lightbox frame assembly [1/2/3/4] to front of verticals [5,6] using

bolts & V4 connectors. See Lightbox Attachment detail.

3) Apply SEG Graphic to front of lightbox assembly. Refer to the SEG Installation

general information page.

When assembled

Item

Qty.

Description

39”w x 12”d Counter Top

BACK VIEW

Connector

set

screw

bolt

Extrusion

Lightbox

Lightbox Connection

Slide V4 connector into groove of vertical

extrusion as shown; secure with set screw.

Attach lightbox extrusion to V4 connector

using bolt.

Counter Top Attachment

Align hole with pin. Rotate pin. Spring

will push pin into hole.

SEG Graphic

Counter

Top

Counter Assembly (cont’d)

Inhaltsverzeichnis

Andere Classic Exhibits Digitale Beschilderung Handbücher

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1363 Bedienungsanleitung

Beliebte Digitale Beschilderung Handbücher anderer Marken

LG 72WS70MS-B Bedienungsanleitung

LG 65SM5D Bedienungsanleitung

LG 55EW5TK-A.AUS Bedienungsanleitung

KeyWest Technology

KeyWest Technology BREEZE Bedienungsanleitung

XtendLan

XtendLan XL-DSP-183C Bedienungsanleitung

LG 47VL10 Bedienungsanleitung

LG WP400 Kurzanleitung

Dynascan

Dynascan DS861LR4 Bedienungsanleitung

LG 22XE1J Bedienungsanleitung

protech

protech KT-7290 Bedienungsanleitung

WebDT

WebDT 515A Montageanleitung

Samsung

Samsung IWJ Series Bedienungsanleitung

LG 55EJ5D Kurzanleitung

EVERI

EVERI Enrollment Kiosk Bedienungsanleitung

LG 75XS4G Bedienungsanleitung

LG 49UH7J Bedienungsanleitung

NCR

NCR SelfServ 90 Handbuch

LG 55EW5F Bedienungsanleitung

Classic Exhibits visionary DESIGNS MOD-1710 Handbuch

Beliebte Digitale Beschilderung Handbücher anderer Marken