Classic Exhibits Sacagawea VK-1221 Handbuch

Order #XXXXX

Scale: 17

10’

Plan View

General Layout

SETUP INSTRUCTIONS

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all setscrews

and locks during disassembly

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Case 1 of 1

Order #XXXXX

Top View of Each Level

Level 1 Level 2

Assembled

Header

(4) Wings

2A,2B

6A 6B

3B,3A

5A, 4A, 4B, 5B

Graphics

Lights

Setup Hardware

Case Packing

Step 1 of 2

Order #XXXXX

Item

2A/2B

3A/3B

4A/4B

5A/5B

6A/6B

Description

Base Plate

42” Vertical Extrusion

45” Horizontal Extrusion

2.5” Angle-Cut Vertical

Qty.

1/1

Completed Backwall

(Front View)

Connection Bar

Back View

5B A

Velcro:

Back/Bottom Edge

Velcro:

Back/Top Edge

Steps:

1) Attach base plates [1] verticals [2A] & [3A], using bolts.

2) Connect verticals [2A] [2B] and [3A] [3B], using connection bars [B].

See Straight Connection with Knobs detail.

3) Connect horizontals [4A] [4B] and [5A] [5B], using connection bars [A].

See Straight Connection with Knobs detail.

4) Connect assemblies [2A/2B] and [3A,3B] with assemblies [4A,4B] and [5A,5B].

See Corner Connection with Knob detail.

5) Connect angled verticals [6A] to [2B] and [6B] to [3B].

See 2.5”h Angle-Cut Vertical Attachment detail.

6) Attach graphic to Velcro on back of assembled Backwall.

Velcro:

Back/Inside Edges

of Verticals

Set Screw

Connector

2.5”h Angle-Cut

Vertical Attachment

Back View of Backwall

Insert connector into groove

of vertical extrusion, then

tighten set screw to secure.

Velcro

Slide connection bar between

extrusions, then turn knobs

clockwise to tighten lock.

Straight Connection

with Knobs

Do not over tighten Knobs

Knob

Corner Connection

with Knob

Turn knob clockwise

to tighten lock.

Do not over tighten Knobs

Knob

Velcro on extrusions

must face to BACK of

assembled Backwall.

Horizontal Placement

Stopper

Set upper horizontals

on top of stopper,

located on verticals.

Backwall Assembly

Step 2 of 2

Order #XXXXX

Graphic

Note: Hesder Frame extrusions

[7] [8] and [9] stay assembled.

Knob

Set Screw

Connector

1) Slide connector of clamp

into extrusion groove.

2) Tighten set screw when

A10 is in desired location.

3) Insert wing into clamp.

4) Tighten knob on clamp

to secure wing in place.

A10 Clamp

Steps:

2) Attach assembled header [7/8/9] to extrusions [5A/5B].

1) Connect lights to extrusions [5A/5B]. See Light Connection detail.

3) Attach graphic to extrusion [3B]. See Graphic Attachment detail.

8) Attach wings to clamps on [2A/2B] and [3A/3B]. See A10 Clamp detail.

Item

7/8/9

Description

Header Frame

Qty.

1/1/1

Completed Assembly

Connector

Graphic Attachment

Cap

Graphic

Standoff

Slide connector into groove of extrusion.

Tighten set screws to secure in place.

Screw standoff into connector. Place

graphic between standoff and cap,

then screw cap to secure graphic.

Slide light onto clip then lock clip

into groove of horizontal extrusion.

Clip

Light

Light Connection

Clip

Light

Horizontal Extrusion

Backwall Attachments

Inhaltsverzeichnis

Andere Classic Exhibits Projektionsfläche Handbücher

Classic Exhibits

Classic Exhibits Sacagawea Designs VK-2109 Handbuch

Classic Exhibits

Classic Exhibits Visionary Designs VK-2967 Handbuch

Classic Exhibits

Classic Exhibits SEGUE DESIGN Sunrise VK-1903 Handbuch

Classic Exhibits

Classic Exhibits Sacagawea Designs VK-1220 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 VK-1400 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Visionary Designs SEGUE DESIGNS VK-1314 Bedienungsanleitung

Classic Exhibits

Classic Exhibits Perfect 10 VK-1401 Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch