Clavia Nord Modular G2 Bedienungsanleitung

Nord Modular G2 Expansion board

Warning! The installation must be carried out by authorized service personnel, otherwise any warranty

becomes void.

The Nord Modular G2 Expansion kit contains

1. The Expansion board

2.Three posts

You will also need a #2 phillips screwdriver and a small wrench.

Installation in the Nord Modular G2 keyboard model

1. Remove the detachable power chord and then remove the 7 black panel screws (marked with circles) according

to the figure. You may also have to loosen (but not remove) the 2 screws marked with triangles in the figure.

2. Remove the 2 larger black screw on the bottom

of the synth (underneath the Mod Wheel and

3. Gently, pull up the lid.

Warning! If you don’t have an anti-static mat, you

have to make sure your free hand is grounded

while handling the Expansion board.

4. Remove the three screws that hold the large board (see figures below) and remove the washers. Replace the

screws with the three enclosed posts. Use a wrench to secure the posts. Hold the Expansion board by the outer

edges so you don’t touch any traces or components. Fit the Expansion board firmly on the two sockets. Secure

the Expansion board on the posts with the three previously removed screws and washers.

5. Gently push the lid back down. Power up the Nord Modular G2 and check connections.

6. Put all the black panel screws back on. Don’t forget the screw on the bottom underneath the Mod Wheel.

Please note: When you power up the NordModular G2, the synth will automatically detect the Expansion board.

In software 1.2 and upwards the letters ’Exp’ after the OS version number will also appear in the main display.

Part No. 50219

Installation in the Nord Modular G2 Engine

1. Remove the detachable power chord and then remove the 5 black panel screws on the front and the 4 black

screws on the rear panel.

2. Gently slide the red lid forward about half a centimeter, then lift up the lid.

Warning! If you don’t have an anti-static mat, you have to make sure your free hand is grounded while

handling the Expansion board.

3. Remove the three screws that hold the large board (see the figures on previous page) and remove the washers.

Replace the screws with the three enclosed posts. Use a wrench to secure the posts. Hold the Expansion board by

the outer edges so you don’t touch any traces or components. Fit the Expansion board firmly on the two sockets.

Secure the Expansion board on the posts with the three previously removed screws and washers.

4. Put the lid back down approximately half a centimeter in front of the bottom panel so it doesn’t touch the

three LEDs.

5. Gently slide back the red lid and make sure the LEDs fit in the holes in the front.

6. Put all the black panel screws back on. Don’t forget the screws on the rear.

When you power on the G2 Engine you will now have the possibility to increase the polyphony in your patches

to twice the original.

Andere Handbücher für Nord Modular G2

Inhaltsverzeichnis

Andere Clavia Elektronische Tastatur Handbücher

Clavia

Clavia Nord Modular V3 Bedienungsanleitung

Clavia

Clavia Nord Electro 3 HP Bedienungsanleitung

Clavia

Clavia Nord Electro 3 Bedienungsanleitung

Clavia

Clavia nord STAGE Bedienungsanleitung

Clavia

Clavia Nord Electro 3 Bedienungsanleitung

Clavia

Clavia Nord Electro 2 Bedienungsanleitung

Clavia

Clavia Nord Lead 3 Handbuch

Clavia

Clavia Nord Electro 4D Bedienungsanleitung

Beliebte Elektronische Tastatur Handbücher anderer Marken

Casio

Casio LK-50 Konfigurationshandbuch

Casio

Casio VZ-1 Fehlerbehebungshandbuch

Casio

Casio Privia PX-100 Bedienungsanleitung

Yamaha

Yamaha PortaTone PSR-225GM Bedienungsanleitung

Behringer

Behringer U-CONTROL UMX49 Bedienungsanleitung

Yamaha

Yamaha Portatone X2500 Bedienungsanleitung

Yamaha

Yamaha Portatone PSR-100 Bedienungsanleitung

Casio

Casio WK-1600 Bedienungsanleitung

Keith McMillen Instruments

Keith McMillen Instruments K-Board Pro 4 Technisches Datenblatt

Yamaha

Yamaha PortaSound PCS-30 Bedienungsanleitung

Roland

Roland Juno-6 Bedienungsanleitung

McGrey

McGrey 6170 Bedienungsanleitung

Yamaha

Yamaha PortaTone PSR-41 Bedienungsanleitung

HDC

HDC Kurzweil KP300X Bedienungsanleitung

Casio

Casio Celviano AP-45 Bedienungsanleitung

Akai

Akai MPK88 Bedienungsanleitung

Waldorf

Waldorf IRIDIUM Bedienungsanleitung

Yamaha

Yamaha NP-30 Montageanleitung