Claypaky IGLOO Bedienungsanleitung

IGLOO

IGLOO EASY

C61195

C61198

IN TRUCTION MANUAL

Congratulations on choosing a Clay Paky product!

We thank you for your custom.

Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure

excellent performance and best meet your expectations and requirements.

Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and

comply with the instructions given in this manual to ensure the fitting is installed, used and serviced correctly and safely.

CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and

maintenance that have not been carried out in conformity with this instruction manual, which must always accompany the fitting.

CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instruction manual at any time and without prior

notice.

ENGLI H

PRELIMINARY

IGLOO

• Installation

Make sure all parts for fixing the equipment are in a good state of repair.

Make sure the point of anchorage is stable before positioning the equipment.

The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if

the primary support system fails, the fitting falls as little as possible.

If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

Carefully read this instruction manual dedicated to the projector inside the IGL .

• Minimum distance from flammable materials

Carefully read this instruction manual dedicated to the projector inside the IGL .

• Mounting surfaces

It is permissible to mount the fitting on normally flammable surfaces.

• Maximun / Minimum environment temperature

Do not operate Igloo if the ambient temperature (Ta) exceeds 40° C (104° F).

The minimum permissible ambient temperature of use is -20 ° C.

When the environment temperature falls below 0 ° C, it is necessary to switch-on projector and

lamp located inside the Igloo, at least 30 minutes before use, so as to lead to thermal regime the

fixture effects.

• IP54 protection rating

Igloo is protected against dust (first digit 5) and splash (second digit 4).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance

according to standard EN 60598-1).

It is, moreover, recommended to protect the supply lines of the equipment from indirect contact

and/or shorting to earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer.

Check that the mains frequency and voltage correspond to those for which the equipment is

designed as given on the electrical data label.

This label also gives the input power to which you need to refer to evaluate the maximum number

of fittings to connect to the electricity line, in order to avoid overloading.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the Igloo, in a thermally

steady state, is 90°C (194°F).

• Maintenance

Before starting any maintenance work or cleaning the device, cut off power from the mains supply.

Carefully read the projector's instruction manual for maintenance of the projector inside the igloo.

Replace any damaged part with original ones.

AFETY INFORMATION

The products referred to in this manual conform to the European Community Directives to which

they are subject:

•Low Voltage 2006/95/CE

•Electromagnetic Compatibility 2004/108/CE

20°C

+40°C

90°C

IP54

IGLOO

IN TALLATION AND TART-UP

Mounting brackets for projector placement - Fig. 1

The dedicated brackets replacing the side handles should be mounted before inserting the projector in the IGL :

C61192 - fast fit bracket for ALPHA 300/700/800

C61191 - fast fit bracket for SHARPY

UNPACKING AND PREPARATION

099115

WARNING:

to avoid damaging the projector,

use the screws supplied with the

bracket unit and not the ones

previously removed.

IGLOO

Projector placement - Fig. 2

nce placed in the igloo the projector is fixed to the base by tightening the screws using 1/4 turns secured to the brackets.

IGLOO

Connecting to the control signal line (DMX) - Fig. 4

Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120 hm characteristic impedance, 22-24 AWG, low capacity. Do not use

microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female

connectors. A terminating plug must be inserted into the last

fixture into the Igloo

with a resistance of 120 hm (minimum 1/4 W) between terminals 2 and 3.

IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be

connected to the shield braid and to pin 1 of the connectors.

Connecting and disconnecting power cable- Fig. 3

IGLOO

LED LANGUAGE

• GREEN LED N: DMX board power on

128

256

512

2345678910

234 1

234

• RED LED

n Bootloader

ff No DMX signal

Relay FF

Slow flashing DMX signal found

Relay FF

Fast flashing No DMX signal

Relay N

Mixed flashing DMX signal found

Relay N

• YELL W LED

ff Not assigned to a transmitter

Mixed flashing Assigned to a transmitter

and no DMX signal

n Assigned to a transmitter and

DMX signal found

Fast flashing link to transmitter lost or

connecting to transmitter

DIP WITCH 1: DMX ADDRESS SETTINGS

The DMX address set on the Dip-switch 1, is the address to control the

switching-on / switching-off of the device via the control unit.

Set dip-switches according to the required DMX address:

Example: DMX 11 address settings

Turn dip-switches 1, 2, 4 ON

DIP- WITCH 2: RECEIVING C NTR L M DE SETTINGS

witch 1, 2, 3 ON: witch 1, 2, 3 OFF:

Wireless operating mode (Radio) Wired operating mode (DMX cable)

BIT % STATUS

101-255

26-100

39.5-100

10.0-39.0

IGLOO SWITCHED-ON

0-25 0.0-9.7

NO FUNCTION

IGLOO SWITCHED-OFF

IGLOO

Closing the device - Fig. 6

Installing Igloo - Fig. 7

WARNING: with the exception of when the

Igloo

is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).

This must be securely fixed to the support structure of the equipment and then connected to the fixing point at the centre of the base.

If the device is fixed to a wall, horizontally, mount the kit C61193 for proper and complete installation Fig.8.

CAUTION:

The 2 IGLOO conveyors

should always be facing down.

By gripping them with both

hands it is possible to rotate

them in the desired position.

An acoustic signal will alert

incorrect conveyor positions.

IGLOO

2 x 183102/802

1 x 105041/003 1 x 033205

1 x 272023/001

Mounting kit C61193 - Fig. 8

C61193 - OPTIONAL ACCE ORIE

IGLOO

CAUTION:

To avoid damage to the internal parts of the fixture, installed inside the IGLOO, when the fixture is not working, is

recommended to turn the head down before turning the fixture off, so that the front lens of the fixture is invested as

little as possible from the sun.

Wireless control - Fig. 10

The wireless control is only available in the IGL version (not EASY).

IGLOO

Lock assembly - Fig. 11

The device latches are fitted with holes for affixing safety locks if desired.

Andere Handbücher für IGLOO

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Claypaky DJ-Equipment Handbücher

Claypaky

Claypaky AXCOR PROFILE 600 Bedienungsanleitung

Claypaky

Claypaky C52153 Bedienungsanleitung

Claypaky

Claypaky TORNADO Bedienungsanleitung

Claypaky

Claypaky ALPHA WASH EASY 1200 Bedienungsanleitung

Claypaky

Claypaky Xtylos Bedienungsanleitung

Claypaky

Claypaky DISPLAY LINE C52134 Bedienungsanleitung

Claypaky

Claypaky IGLOO WL Bedienungsanleitung

Claypaky

Claypaky SCENIUS UNICO Bedienungsanleitung

Claypaky

Claypaky K-EYE K10 HCR Bedienungsanleitung

Claypaky

Claypaky HY B-EYE K15 Bedienungsanleitung

Claypaky

Claypaky STAGE SCAN Bedienungsanleitung

Claypaky

Claypaky K-EYE HCR Bedienungsanleitung

Claypaky

Claypaky CP COLOR 400 Bedienungsanleitung

Claypaky

Claypaky MINISCAN HPE HTI 300W/DX Bedienungsanleitung

Claypaky

Claypaky POINT Bedienungsanleitung

Claypaky

Claypaky SHARPY PLUS AQUA Bedienungsanleitung

Claypaky

Claypaky DISPLAY LINE Bedienungsanleitung

Claypaky

Claypaky AXCOR SPOT 300 Bedienungsanleitung

Claypaky

Claypaky POINT MH Bedienungsanleitung

Claypaky

Claypaky Mini-B ParLED Aqua Bedienungsanleitung

Claypaky

Claypaky AXCOR SPOT 400 Bedienungsanleitung

Claypaky

Claypaky ALPHA PROFILE 1500 Q Bedienungsanleitung

Claypaky

Claypaky scenius spot Bedienungsanleitung

Claypaky

Claypaky ALPHA PROFILE 700 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung