Clearaudio TT2 Bedienungsanleitung

User manual

Bedienungsanleitung

TT2

Pic. similar / Abb. ähnlich

User manual / Bedienungsanleitung

Page / Seite 2 © clearaudio electronic GmbH, 2022-01

User manual ..............................................................2 - 17

Bedienungsanleitung.................................................18 - 33

Dear audio enthusiast,

Congratulations! You have purchased one of the best tangential tonearms available in the world of

high-end audio.

Your Clearaudio

TT2

tonearm has the capability to extract unprecedented performance from

absolutely ANY phono cartridge!

To achieve the full performance and to avoid any damages to this product, please take your time to

get familiar with your Clearaudio

TT2

tonearm.

Your Clearaudio

TT2

tonearm will give you many years of musical enjoyment and pleasure.

Clearaudio electronic GmbH

User manual / Bedienungsanleitung

Made in Germany Page / Seite 3

Safety instructions

1. Maintenance

• Please make sure that the precision dry ball bearings are not touched, cleaned or lubricated in

any way.

• Never move or readjust the screws in the tonearm carriage. They should be adjusted only by

qualied dealers or at the Clearaudio factory.

• Use a cotton bud and a commercially available glass cleaner to clean the glass tube. Put some

glass cleaner on the cotton bud and slide it through the glass tube with a movement from the

inlet to the outlet groove.

2. Transportation

Should further transportation of the

TT2

tonearm be necessary, please always use the original

packing material. Otherwise serious damage could occur.

During any transportation of the tonearm, always protect the carriage with a piece of

foam so that the carriage cannot move during transportation.

When repackaging the tonearm, please follow in reverse the steps indicated in this

manual for installation and setup.

3. Service

If any servicing or repair of a Clearaudio product is necessary, please rst contact your dealer or

distributor. Alternatively contact Clearaudio directly and we will advise you of your nearest service

location.

PLEASE RETAIN ALL ORIGINAL PACKAGING. You will need it if this product has to be transported

and/or shipped. Any further questions you may have about this product should be directed to your

local dealer.

4. Safety instructions

Disposal

This product is not allowed to be disposed with household waste.

WEEE Reg.No.: DE26004446

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not handle the mains lead with wet hands.

No naked ame sources, such as lighted candles, should be placed on the equipment.

Only for use on turntables.

User manual / Bedienungsanleitung

Page / Seite 4 © clearaudio electronic GmbH, 2022-01

Contents

1. List of components.......................................................5 - 6

2. Mounting the tonearmbase..........................................7 - 9

2.1 on the Clearaudio Performance DC / Ovation

2.2 on any Clearaudio Innovation series turntable

2.3 on other manufacturer‘s turntables

TT2

set up ....................................................................10 - 11

4. Inserting the headshell tube .......................................11 - 12

5. Mounting the cartridge................................................12

6. Pre-setting the tracking force......................................13

7. Fine adjustment of the tonearm..................................14 - 16

7.1 Adjustment of the tangential alignment

7.2 Adjustment of the VTA

7.3 Adjustment of the azimuth

8. Technical data..............................................................17

Warranty information......................................................34 - 35

User manual / Bedienungsanleitung

Made in Germany Page / Seite 5

1. List of components

The Clearaudio

TT2

tonearm is delivered in a special packing to ensure its safe transport.

Please check the contents as shown in the picture below.

Important note:

Please take special care of the tonearm cable while unpacking your Clearaudio

TT2

tonearm!

Note: All threads are metrical!

Pic. 1: List of components

1 2

2 a

7 8

User manual / Bedienungsanleitung

Page / Seite 6 © clearaudio electronic GmbH, 2022-01

TT2

tonearm with pre-mounted

tonearm carriage

6. Clearaudio linear gauge

(alignment gauge to adjust tangential

tracking)

2 a

Aluminium folding base with pre-

assembled height adaptor (10mm) and

screws M4x40

Height adaptor (14.5mm)

7. Clearaudio Mini Level Gauge

3. 1x Hex wrench (# 1.5)

1x Hex wrench (# 2)

1x Hex wrench (# 2.5)

1x Hex wrench (# 3)

8. 1 pair of white gloves

4. High-precision silver carbon bre arm

tube and stainless steel headshell with

pre-mounted counterweights

4pcs: 2.3g / 2.6g / 4.3g / 8g /17.6g for

Goldnger Statement;

(without cartridge)

9. Not shown:

Warranty card;

user manual;

Clearaudio Quality Certicate (CQC) and

return delivery note

5. Base mounting screws:

3x M4 x 30mm

(for mounting without height adaptor)

Cartridge mounting screws

(not shown):

2x M2.5 x 12mm

2x M2.5 x 14mm

User manual / Bedienungsanleitung

Made in Germany Page / Seite 7

2. Mounting the tonearm base and folding base

2.1 Mounting the tonearm base and folding base on a Clearaudio Performance DC or

Ovation turntable

Please check if the correct tonearm base is mounted on your turntable (Pic. 2).

If not, place the turntable on the edge of a table or similar surface,

so you have access to the tonearm base from below. Remove the

previous tonearm base by loosening the six M4 x 35mm screws

with a hex wrench on the bottom side of the clamping ring.

Exchange the tonearm base for the correct one (see pic. 2) and

loosely tighten it so the tonearm base is still rotatable.

Now you can t the folding base and the dedicated height-

adaptor with the screws provided (Pic. 1, #5; page 5), using the

hex wrench #3 (Pic. 1, #3; page 5). Please make sure that the bases sit perfect on the turntable.

To mount the height adaptor with 14.5mm and 10mm you will need the M4 x 40 screws which are

already pre-mounted.

If you don’t need the height adaptor, then use the M4 x 30 screws (Pic. 1, #5; page 5).

The height adaptor will be required depending on the dimensions of the turntable and cartridge.

Our dealer/distributor will help you or contact Clearaudio directly.

Now you can tighten all of the screws (see Pic. 4). Folding base

Height adaptor

Tonearm base

Pic. 3: Mounting the folding base

Pic. 4: Tightening the screws

Pic. 2: Tonearmbase for Performance

DC & Ovation (Art. No. AC031-3)

User manual / Bedienungsanleitung

Page / Seite 8 © clearaudio electronic GmbH, 2022-01

Pic. 5: Tonearmbase for Innovation

Serie (Art. No. AC030-7)

2.2 Mounting the tonearm base and folding base on a Clearaudio Innovation series

turntable

Please check that the correct tonearm base is mounted on your turntable (Pic. 5).

If the tonearm base is already pre-assembled, it is in a position

which is optimized for the packaging. The position of the tonearm

base will be correct during the adjustment of the tonearm.

If not, then remove previous tonearm base by loosening the screw

of the aluminium base with a 7mm hex wrench.

Exchange the tonearm base for the correct one (see Pic. 5) and

place it so that the long side of the tonearm base points counter-

clockwise. Now you can loosely tighten it so that the tonearm base

is still rotatable.

Next, t the folding base and the dedicated height adaptor with the screws provided (Pic. 1, #5; page

5) and the hex wrench #3 (Pic. 6). Please make sure that the bases sit perfectly on the turntable.

To mount the height adaptor with 14.5mm and 10mm you will need the M4 x 40 screws which are

already pre-mounted. If you don’t need the height adaptor, then use the M4 x 30 screws

(Pic. 1, #5; page 5).

The height adaptor will be required depending on the dimensions of the turntable and cartridge.

Our dealer/distributor will help you or contact Clearaudio directly.

Now you can tighten all the screws (see Pic. 7).

Pic. 6: Mounting the folding base

Pic. 7: Tightening the screws

Folding base

Height adaptor

Tonearm base

User manual / Bedienungsanleitung

Made in Germany Page / Seite 9

Pic. 8: Drilling template

2.3 Mounting the tonearm base and folding base on a other manufacturers’ turntables

In order to mount the tonearm base on the turntable chassis, please rst drill three holes into the

turntable chassis. To ensure the correct position of the three holes, please use the measurements

given in the drawing template below. For this step, use a 3.3mm drill. After you have drilled the

three holes, thread the holes using an appropriate tap cutter. If the material of the turntable chassis

is not suitable for threading, please use a 4.5mm drill for the holes. In this case you will need longer

screws with nuts to t the tonearm base.

Now you can mount the tonearm base on the clean and dry surface of the turntable chassis.

Please note that this image is not true to scale.

User manual / Bedienungsanleitung

Page / Seite 10 © clearaudio electronic GmbH, 2022-01

Pleaseremovethefoamusedforsafetransportation

of the tonearm carriage.

Turn the height adjustment screw clockwise until

the gap between head of the screw and tonearm

housing is approx. 1cm.

Remove the height adjustment screw by loosening

with 2.5mm hex wrench (Pic. 10).

Now open the folding base so that the rods are

horizontal and place the tonearm on the support

bars until the lower end of the height adjustment

screw becomes visible in the height adjustment

screw hole (Pic. 11).

Secure this setting by re-inserting the height

adjustment screw and tightening it by hand

(Pic. 12).

Pic. 11: Mounting the tonearm

Pic. 10: Remove the height adjustment screw

Pic. 9: Fixing the height adjustment

TT2

set up

Pic. 12: Secure the tonearm

approx. 1cm

Andere Handbücher für TT2

Inhaltsverzeichnis

Sprachen:

Andere Clearaudio Musikequipment Handbücher

Clearaudio

Clearaudio Universal Bedienungsanleitung

Clearaudio

Clearaudio double matrix professional SONIC Bedienungsanleitung

Clearaudio

Clearaudio Essence mc Bedienungsanleitung

Clearaudio

Clearaudio Tracer Bedienungsanleitung

Clearaudio

Clearaudio Concept MC Bedienungsanleitung

Clearaudio

Clearaudio Talismann V2 Gold Bedienungsanleitung

Clearaudio

Clearaudio loving music Bedienungsanleitung

Clearaudio

Clearaudio balance V2 Bedienungsanleitung

Clearaudio

Clearaudio Concept MC Bedienungsanleitung

Clearaudio

Clearaudio TT3 Bedienungsanleitung

Clearaudio

Clearaudio Profiler Bedienungsanleitung

Clearaudio

Clearaudio Statement TT1 Bedienungsanleitung

Clearaudio

Clearaudio double matrix professional SONIC Bedienungsanleitung

Clearaudio

Clearaudio Speed Light V2 Bedienungsanleitung

Clearaudio

Clearaudio Jubilee MC Bedienungsanleitung

Clearaudio

Clearaudio concept V2 Bedienungsanleitung

Clearaudio

Clearaudio Satisfy Kardan Bedienungsanleitung

Clearaudio

Clearaudio VTA-Lifter Bedienungsanleitung

Clearaudio

Clearaudio Emotion-CMB Bedienungsanleitung

Beliebte Musikequipment Handbücher anderer Marken

DAPAudio

DAPAudio IPS-PT Bedienungsanleitung

Dynacord

Dynacord DPM 8016 Bedienungsanleitung

Subdecay

Subdecay Starlight Flanger Bedienungsanleitung

Moen

Moen GEC8 Live Bedienungsanleitung

Fender

Fender 1 Bedienungsanleitung

Yamaha

Yamaha MLC-16 Bedienungsanleitung

Sonuscore

Sonuscore TIME TEXTURES Bedienungsanleitung

flight of harmony

flight of harmony V'Amp Bedienungsanleitung

NANO

NANO PERFORMANCE MIXER Bedienungsanleitung

Tascam

Tascam CD-GT2 Bedienungsanleitung

BHI

BHI NEIM 1031 MKII Bedienungsanleitung

Befaco

Befaco KICKALL Bedienungsanleitung

Paia

Paia 9720 Leitfaden

limex

limex ALPIN MASTER 128 Bedienungsanleitung

nord

nord Electro 3 Bedienungsanleitung

Joemeek

Joemeek sixQ2 Bedienungsanleitung

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Bedienungsanleitung

Furutech

Furutech ADL GT40 Installationsanleitung