ClearSounds QH2 Bedienungsanleitung
Æ
Æ
Æ
Æ
Æ
Æ
QUICK START GUIDE
1. SETTING UP THE QH2 HUB FOR CORDED TELEPHONES
2. TO PAIR THE QH2 HUB WITH A BLUETOOTH HEADSET, STREAMER OR NECKLOOP
STEP 1: Remove the
curly cord from the
phone base and
connect it to the
HANDSET port on
the bottom of the
hub.
STEP 1: Wear your
Bluetooth listening
device and remain
within 33 feet of the
QH2 hub.
STEP 2: On the hub,
press and hold the
multi-function
button (MFB) until
the blue and red
lights flash.
STEP 3: Turn on
your listening
device, then place it
in Bluetooth pairing
mode. When hub
and listening device
are paired, the hub
flashes a blue light
every three
seconds. Your
listening device also
indicates when
pairing is success-
ful.
STEP 4: Confirm
that you hear a dial
tone in the handset
by manually lifting
the handset from
the base.
STEP 5: On the hub,
press and release
the MFB to hear the
dial tone in your
Bluetooth headset,
neckloop or
streamer.
STEP 6: Press and
release the MFB.
The dial tone stops.
Manually return the
handset to the base.
STEP 2: Connect
the short
Hub-to-base cable
to the phone base
port where the curly
cord had been
connected.
STEP 3: Connect
the unattached end
of the Hub-to-base
cable to the BASE
port on the top side
of the hub. The
green light will
illuminate.
STEP 4: Connect
the round end of the
AC power adapter
to the DC 9V port on
the left side of the
hub, then plug the
other end of the AC
adapter into a
power outlet in the
wall.
STEP 5: Pick up the
telephone handset.
If you hear a dial
tone: On the hub,
slide the VOLUME
slider or TONE
slider until you hear
a noticeable change
in volume and tone
quality.
STEP 6: If you do
not hear a notice-
able dial tone: On
back of QH2, click
the dial until you
hear a dial tone. On
the hub, slide the
VOLUME slider or
TONE slider until
you hear a change
in volume and tone
quality. Repeat
these steps until
you find a compati-
ble setting.
For full manual visit www.clearsounds.com
Æ
Æ
Æ
Æ
Æ
Æ
Æ
TO MAKE OR ANSWER A CALL USING A CORDED PHONE WITH HANDSET LIFTER CONNECTED
OPTIONAL LIFTER SET UP FOR THE QH2 HUB *Lifter not included*
QUICK START GUIDE
Æ
Æ
Æ
Æ
3. TO MAKE OR ANSWER A CALL USING A CORDED PHONE
STEP 2: Manually
lift the handset from
the base.
STEP 2: On the underside
of the lifter, remove the
paper backing from the
two pieces of tape.
STEP 3: Firmly press the
bottom of phone base lifter,
directly below the earpiece,
so that it lies beneath the
handset arm.
STEP 4: Connect the
L-shaped connector to
the LIFT port on the
bottom of hub...
STEP 5: ...then connect
the other end of the
cable firmly to the port
on the top of the lifter.
Look for a red glow the
on lifter.
STEP 3: On the hub,
press and release
the MFB. You will
hear a dial tone or
the caller in your
listening device.
Dial or talk.
STEP 1: Remove the
handset from the
phone base.
STEP 2: On the hub, press
and release the MFB. The
lifter raises the phone
handset and you hear a dial
tone or the caller in your
listening device. Dial or talk.
STEP 3: Slide the
TONE slider on the
hub until you hear the
tone that you prefer
[ OPTIONAL]
STEP 4: To end the call,
press and release the MFB
and the lifter returns the
phone handset to the base.
STEP 4: Slide the
TONE slider on the
hub until you hear
the tone that you
prefer.
[ OPTIONAL ]
STEP 5: To end the
call, press and
release the MFB.
STEP 6: Manually
hang up the hand-
set.
Please Note: You will need to manually remove the handset from the base to make a
call and replace it to hang up.
Please Note: Bluetooth connection required for lifter.
STEP 1: Wear your
Bluetooth listening
device and remain
within 33 feet of the
QH2 hub.
STEP 1: Wear your
Bluetooth listening
device and remain
within 33 feet of the
QH2 hub.
Andere Handbücher für QH2
1
Inhaltsverzeichnis
Andere ClearSounds Schalten Handbücher
