Clevertronics LP CUBPRO Series Bedienungsanleitung

1943041

V1.6

19 May 2022

Instruction Sheet Template - V1.2 –Updated 06/10/2021

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks, HIVE (HV/HVG) and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -HVG -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also

be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of thetest switch or by scanning thesupplied barcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, HVG,

DATA

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire, please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

LP™ Ultrablade Pro LED Exit

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements

of AS2293.3: 2005 and AS/NZS CISPR15: 2017

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

CUBPRO-yy-xx-zz-ss-ww-vv

Testing:

Options:

Manual Test

xx = Blank

Theatre

yy= TH

Running Man

zz=R

Zoneworks

xx = ZW

Custom Option

Running Man Left Arrow

zz=RL

Z/W DATA

xx = DATA

Black

vv = BLK

Running Man Right Arrow

zz=RR

Zoneworks HIVE

xx = HV/HVG

Double sided R/M

zz=DS-R

DALI Registered.

xx = DALI

Double sided R/M Arrow

zz=DS-RAOW

Clevertest

xx = CT

Special Cable Option

ww = F5C, 5C

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest PLUS

capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1550105

Replacement Battery

2310250

Replacement Emergency LED Lamp

2740054

Ultrablade to Ultrablade Pro adapter

AUM02370020001

Replacement Emergency Driver

AUM02370160001

Replacement Emergency Driver (For TH-DS Options ONLY)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1943041

V1.6

19 May 2022

Instruction Sheet Template - V1.2 –Updated 06/10/2021

Installation:

The LP Ultrablade Pro LED Exit (CUBPRO) is a recessed ceiling mount fitting. The CUBPRO can be

attached directly to any solid surface, or to a ceiling tile with the integrated clamping mechanisms. The

CUBPRO comes with an attached Flex and Plug. Please follow the steps below to install the CUBPRO

Exit:

•If replacing an Ultrablade, an Ultrablade to Ultrablade Pro adapter 2740054 (sold separately)

is required)

•Create a cut-out (350mm x 48mm) in the mounting surface.

•Route the power cord to the mains connection and connect the 240VAC supply.

•Insert the CUBPRO into the ceiling cavity tighten the (4) clamping screws.

•The standard maximum ceiling thickness is 18mm. Trim Clamp as per below image for ceiling

thickness up to 25mm.

•Alternately, fix the CUBPRO to a solid surface using (4) screws through the surface material.

•Install the cover plate.

•Apply power to the fitting and test.

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four

Segment Marking on the product will include an ‘’F’’ in third segment block.

Dimensions:

Changing EXIT Legend Inserts:

The Ultrablade Pro Exit comes with an assortment of standard legends.

1. To remove the legend, grasp the centre of the bottom trim piece and pull down slightly to

expose the legend edge. See photo.

2. Grasp the bottom edge of the legend and slide the existing legend out of the blade, while

working the edges out along the sides.

3. Slide the new legend into the blade, ensuring to fit the edges into the sides then slide the

legend to the top of the blade. Insert one bottom corner then the other. Slide the legend down

into the bottom trim.

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Ultrablade Maintenance:

LED Lamp Replacement:

•Use only the LED Strip recommended in

the Spares Parts list of this instruction.

•Disconnect battery from LED driver pack

and cut cable tie to remove.

•Disconnect the signal cable from LED strip,

loosen screw and remove the mains driver

pack.

•Remove 4 self-tapping screws and unclip

the LED strip.

•Install the new LED strip following the

above procedure in reverse.

Battery Replacement:

•Use only the battery recommended in the

Spares List on this instruction.

•Remove the cable ties holding the battery,

un-plug the lead from the battery connector

remove the old battery.

•Plug the new battery into the battery

connector.

•Secure the battery using suitable cable ties

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1, not applicable

for –TH (theatre) version (refer to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Andere Clevertronics Beleuchtungsausrüstung Handbücher

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics ECFLED-LI-TH Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 LBS2N Series Bedienungsanleitung

Clevertronics

Clevertronics L10 Argonaut PLUS Bedienungsanleitung

Clevertronics

Clevertronics CLP CCFPRO Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 Cleverfit Pro Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Technische Daten

Clevertronics

Clevertronics CLP CCIRC Series Handbuch

Clevertronics

Clevertronics L10 CleverFit Exit LCFLED Series Bedienungsanleitung

Clevertronics

Clevertronics L10 Supalite LFLLED Series Bedienungsanleitung

Clevertronics

Clevertronics LP CBS4LEDS DIF Series Technische Daten

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE-PRO-SMS-SPOT Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics LP Argonaut PLUS Montage- und Bedienungsanleitung

Clevertronics

Clevertronics GLIDER-SM Montage- und Bedienungsanleitung

Clevertronics

Clevertronics CBULKy Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Montage- und Bedienungsanleitung

Clevertronics

Clevertronics CLP Ultrablade Pro CUBPRO Series Handbuch

Clevertronics

Clevertronics Argonaut PLUS Wartungs- und Serviceanleitung

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Montage- und Bedienungsanleitung

Clevertronics

Clevertronics LP CWSQLED Series Bedienungsanleitung

Clevertronics

Clevertronics TS Trade Series Montage- und Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung