Clifford GP500 Bedienungsanleitung
Maintenance
Your GP500 system requires no maintenance except for replacement of
remote control batteries when they reach the end of their useful life. For
further information on this, see the Automatic low battery warning and Remote
control battery replacement sections on page 13.
This product, like any electrical device on your motorcycle, requires that
your motorcycle battery be in proper working order and fully charged. To
ensure proper operation, periodically have your motorcycle battery
“load-checked” at any local garage/mechanic and ask them to verify that the
charging system is working properly. Also make sure that the battery cables
and connections are tight and free from corrosion.
User’s Manual/299 1
Welcome to the world of high-technology
vehicle security and convenience
Congratulations on the purchase of your GP500 motorcycle
security/convenience system.
Your remote controls
The weather resistant pair of remote controls that are provided with GP500
are ultra-sophisticated miniature radio transmitters powered by a single
miniature battery (a 3-volt lithium).
2GP500
Remotely controlling your GP500
Each of your two remote controls can command several different functions.
TO ARM:Press button I on the remote control. You will
hear two chirpsand the indicator lights will flash
twice. The LED will flash repeatedly.
TO DISARM:Press button I on the remote control. One chirp
and one indicator light flash confirms disarming
and the LED turns off.
TO ARM OR
DISARM SILENTLY:By pressing button II on the remote control, you
can arm or disarm your GP500 with all the
indications previously noted exceptthe chirps.
TO ACTIVATE
THE BIKE BEACON
LOCATOR:
For three seconds, continuallypress button I on the
remotecontrol. The indicator lights will flash
repeatedly and the siren will blare until you press
the button again to turn it off.
User’s Manual/2993
TO ACTIVATE
INSTANT
AUTOARMING
BYPASS:
Press button III on the remote control and hold
for three seconds. Two indicator light flashes
confirm that GP500 will NOT AutoArm. If you
press and hold button III for three seconds once
more, the system will respond with one indicator
light flashwhich means that AutoArming has been
reactivated. The next time the motorcyle is
parked, the GP500 system resumes normal
AutoArming operations.
OTHER FEATURESOther features can be accessed as noted in the
following chart:
4GP500
QUICK REFERENCE: REMOTE CONTROL FUNCTIONS
FunctionPress
button(s)
Arm or disarmI
Silently arm or disarm II
Instant AutoArming Bypass (press and hold button for three seconds
while system is disarmed)III
Dual-Level Piezo Sensor Warning Level Bypass (press button within
10 seconds after arming the system)III
Dual-Level Piezo Sensor Total Bypass (press and hold button for
three seconds within 10 seconds after arming the system) III
Digital Tilt/Motion Sensor Warning Zone Bypass (press buttons
within 10 seconds after system is armed)II + III
Digital Tilt/Motion Sensor Total Bypass (press and hold buttons for
three seconds within 10 seconds after system is armed)II + III
Dual-Level Piezo Sensor Adjustment (press and hold buttons for
three seconds while system is disarmed. See page 21 for complete
instructions)II + III
Unassigned*I + II
Unassigned*I + III
* Can be assigned to Clifford ACG-2 systems on your other vehicles.
User’s Manual/2995
ACG-2™ (Anti-CodeGrabbing 2™)
Clifford’s ACG-2 protects your motorcycle from thieves’ remote control
“cloning” devices that are used to record the disarming code transmitted
from your remote.
Automatic remote control low-battery warning
If your remote control battery is very low, you will hear five rapid chirps when
you disarm rather than the single chirp that you normally hear.
Remote control battery replacement
Any Authorized Clifford Dealer willbe happy to replace a remote control
battery for you without cost provided you purchase the replacement battery
at their shop (it’s also a good idea to keep a spare battery on-hand just in case).
1.Insert a small, thin screwdriver blade in the slot near the keyring opening
(you may leave the keyring in place) and turn it to separate the two
halves.
2.Remove the old battery noting the + and – indications and replace it.
3.Put the enclosure back together by first aligning the top of the remote,
then snapping the case back together at the bottom.
6GP500
Two-Point Internal Immobilisation
Please be aware that the AutoArming feature has no effect on
Immobilisation. The system automatically immobilizes your vehicle’s starter
and ignition 30 seconds after engine shutdown or when you arm with the
remote control.
When you remotely disarm your GP500 system, the Immobilisation circuits
will automatically disengage. You then have 30 seconds in which to start the
engine (or turn the ignition switch to its “ON” position).
If more than 30 seconds pass, the immobilizer will automatically reactivate.
This will be visually indicated by the LED repeatedly flashing, but at a slower
rate than that of the normal rapid “armed” indication flash rate.
TodisarmtheImmobilizerifithasarmed itself, use the
remote control to arm and then disarm the system, or
turn on the ignition and press button I on the remote
control.
User’s Manual/2997
AutoArming™
If this feature is enabled and you forget to remotely arm. After 30 seconds
pass, the system is automatically armed. In instances where you want to
bypass AutoArming, such as when fueling the motorcycle, simply turn the
ignition on and then off again after you have parked.
Digital Dual-Zone Tilt/Motion Sensor
Clifford’s Digital Tilt/Motion Sensor detects one degree of tilting or any
minute forward/reverse motion of the motorcycle while completely ignoring
all other conditions that falsely set off other sensors. Even if you park your
motorcycle on the steepest hill, it will accurately respond to the first hint of
tampering.
The Digital/Tilt Motion Sensor will first provide a five chirp warning if the
motorcycle tilts more than one degree. Once the motorcycle tilts more than
two degrees, the full alarm will sound.
TO REMOTELY
BYPASS THE
WARNING ZONE:
During the first 10 seconds after arming the
system remotely, simultaneously press buttons II
and III on the remote control. The system
provides four indicator light flashes when the
warning zone is bypassed.
8GP500
Andere Handbücher für GP500
2
Inhaltsverzeichnis
Andere Clifford Sicherheitssystem Handbücher
Clifford
Clifford 3606X Bedienungsanleitung
Clifford
Clifford SuperNova II Bedienungsanleitung
Clifford
Clifford GP1000T Bedienungsanleitung
Clifford
Clifford IntelliGuard 8000 Bedienungsanleitung
Clifford
Clifford GP1000T Bedienungsanleitung
Clifford
Clifford Bullet 4 Bedienungsanleitung
Clifford
Clifford GP500 Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung