Climax VDP-3 Bedienungsanleitung
VDP-3
Video Door Phone
User Manual
June-10-2020
1
Table of Contents
INTRODUCTION______________________________________________________________________________ 2
1. APPLICATION OVERVIEW_______________________________________________________________ 3
1.1. PARTS IDENTIFICATION____________________________________________________________3
1.2. THE POWER SUPPLY _____________________________________________________________3
1.3. LED INDICATOR _________________________________________________________________4
1.4. EQUIPMENT REQUIRED ____________________________________________________________4
1.5. HARDWARE INSTALLATION _________________________________________________________5
1.6. SETUP ________________________________________________________________________6
2. OPERATION ____________________________________________________________________________ 9
2.1. WEB BROWSER ACCESS __________________________________________________________9
2.2. SMARTPHONE ACCESS___________________________________________________________10
2.3. DOORBELL NOTIFICATION_________________________________________________________12
2.4. VIDEO /PICTURE CAPTURE AND EVENT HISTORY________________________________________13
3. REMOTE PROGRAMMING_______________________________________________________________ 14
3.1. APP USER SETTING _____________________________________________________________14
3.2. ACCOUNT USER INFO ____________________________________________________________15
3.3. VIDEO SETTING ________________________________________________________________15
3.4. VDP SETTING _________________________________________________________________18
2
Introduction
VDP-3 Video Door Phone is designed to replace conventional doorbell by providing
remote video streaming access, two-way communication via Wi-Fi network. The Video
Door Phone functions as a part of Climax alarm system by connecting to a Climax
security system Control Panel. Setup and remote access of Video Door Phone is
performed via smartphone application developed by Climax Technology.
3
1.Application Overview
1.1. Parts Identification
Front View
Front View
(cover removed)
Back View
1. Protective Cover
2. Camera Lens
3. Function Button / LED Indicator (Blue / Amber)
4. IR Lens
5. Cover Fixing Screw
6. Mounting Hole
7. 12~24V DC/AC Power Input
Please note the torque on the screw should be less than 24.5 Nm (2.5 kg-m).
8. 12~24V DC/AC Power Input
Please note the torque on the screw should be less than 24.5 Nm (2.5 kg-m).
9. Reserved
10.Reserved
1.2. The Power Supply
The VDP uses 12~24V DC/AC power as its power source. Turn off mains power first.
Loosen the two screws of the 12~24V DC/AC Power Input, and save the screws for later
use. Connect wires to the inputs on the rear side of the back cover*; install the VDP to
power on the device.
*Note: It is recommended to use wire with a diameter less than 15mm to connect to the
power input. The torque on the screw should be less than 24.5 nm (2.5 kg-m).
4
1.3. LED Indicator
The Video Door Phone has built-in Blue and Red LEDs to indicate device status.
LED Color
Behavior
Indication
Blue
Flash every 3 seconds
VDP under Wi-Fi setup mode (AP mode)
Spinning
VDP button pressed, waiting for answer
ON
VDP under video streaming and two-way
communication
Amber
ON for 3 seconds
VDP finish warm up upon power on,
entering normal operation.
Flash every 3 seconds
Wi-Fi connectivity problem*
Flash every second
VDP unable to connect to server
3 Flash then ON for 6
seconds
VDP reset to factory default
*Note: It takes about 1 minute for VDP to connect to Wi-Fi after power on. Before the
Wi-Fi connection is established, the Red LED may flash momentarily.
1.4. Equipment required
The following equipment is required to use VDP:
A router supporting 2.4 GHz Wi-Fi network. The VDP should be connected to this
router with access to internet and Home Portal Server.
An iPhone or Android smartphone
Android version requirement: Android 5.1 or above.
iPhone version requirement: iOS 9or above.
To use the VDP, a Climax IP based security system alarm panel is required –The
panel must be registered in Climax Home Portal Server with a valid user account.
Refer to panel and Home Portal Server user guide to complete panel setup and
registration process.
5
1.5. Hardware Installation
Step 1. Before you start, find the circuit breaker or fuse box.
Step 2. Once you have found it, open the door and turn off the main power switch.
Step 3. Take out the VDP from the package. Remove the protective cover and put it
aside for later use.
Step 4. Flip the VDP up-side-down and locate the 4 screws near the bottom of the VDP.
Step 5. Loosen the 2 screws of the 12~24V DC/AC Power Input, and save the screws
for later use.
Step 6. Connect wires to the inputs on the rear side of the back cover, as shown in
Figure 1. It is recommended to use wire with a diameter less than 15mm to
connect to the power input. Please note the torque on the screw should be less
than 24.5 nm (2.5 kg-m)
Step 7. Locate the 2 mounting holes on the VDP, as shown in Figure 2, and screw the
VDP into the wall.
Figure 1
Figure 2
Step 8. Replace the protective cover on top of the VDP and tighten the cover fixing
screw.
Step 9. Switch on the circuit breaker to provide power to the VDP.
6
1.6. Setup
The Video Door Phone can be incorporated into existing Climax security system as an
accessory device. To use the VDP, a Climax IP based security system alarm panel is
required.
In order to incorporate the Video Door Phone into existing Climax security system, the
Control Panel of the security system must be registered into Climax Home Portal Server
first with a functional user account.
A smartphone with Vesta Home 5 TW / Vesta Home 5 US or Vesta Home 5 EU app
installed is required to perform setup. Search for the app in Google Play or Apple App
Store, type Vesta Home 5 TW/US/EU on the search bar according to your server, then
download the application. Refer to Climax Home Portal Server user guide for detail.
1. Open Vesta Home 5 app and enter your existing user account & password of the
Control Panel you wish to use for further setup.
2. Tap the Camera icon in the navigation bar and the + icon on top left corner to add the
VDP into your existing system. Select the VDP icon and tap “Next”.
3. Power up the Video Doorbell by applying AC power. The device will first warm up for
about 30 seconds, and its Blue LED will begin to flash.
Flashing LED indicates the Video Doorbell does not have a working Wi-Fi setting yet.
It will enter Wi-Fi setup mode (AP mode) automatically upon power-up.
4. Select the route to set up your Wi-Fi network and follow on-screen instructions.
Please note if the VDP has already been set up to another Wi-Fi network, be sure to
reset the device first before adding it into your existing alarm system.
4.1. Manual: Use your VDP as an AP. Connect to your Wi-Fi. Make sure your
smartphone’s Wi-Fi is enabled. Follow on-screen instructions and wait for your
VDP to connect to your Wi-Fi network. After successfully joining to your Wi-Fi
7
network, the app proceeds to learn the VDP into the Control Panel. When
learning is completed, re-login to the app and start using your VDP.
4.2. QR Code: Enter your SSID information to generate QR Code for VDP to scan.
The QR Code includes information about the Wi-Fi network and the Control Panel.
Follow on-screen instructions. Tap “QR Code”for your smartphone to display it. VDP
8
will emit a short beep to indicate the scanning is successful. When the LED stops
flashing, tap “Done”to complete the setup. After VDP successfully joins to your Wi-Fi
network, the app will proceed to learn the VDP into the Control Panel. When learning
is completed, the VDP is able to be viewed on the app.
9
2.Operation
The Video Door Phone can be accessed by web browser and or smartphone application.
Two-way voice communication function is only available via smartphone access.
2.1. Web Browser Access
When accessing the Home Portal Server account of the Control Panel using a web
browser, VDP is located under the Camera page and has the same function of a Climax
IP Camera.
Two-way voice and doorbell functions are not enabled for web browser access. To uses
these functions, a smartphone app is required. Please see 22. Smartphone Access for
detail.
Click the Setting button to access video adjustment and timestamp location
setting. Adjust the setting and click Submit to confirm.
Press the Record Video button to record a video clip.
Inhaltsverzeichnis
Andere Climax Gegensprechanlage Handbücher
