Climax SD-16-ZBS Bedienungsanleitung

Smoke Detector

SD-16-ZBS / SD-16SL-ZBS

Introduction

SD-16(SL)-ZBS is a ZigBee Smoke Detector. It is capable of sending wireless signals to the coordinator

in the ZigBee network upon detection of smoke particles. The Smoke Detector is designed to be

mounted on ceiling or top of stairwells when smoke would concentrate to raise alarm timely and protect

your home from fire hazards.

The Smoke Detector utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless

communication protocol that is reliable and has low power consumption and high transmission efficiency.

Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network

and coordinated for data exchange and signal transmission

The Smoke Detector serves as an end device in the ZigBee network. It can be included in the ZigBee

network to transmit signal upon activation, but cannot permit any other ZigBee device to join the network

through the Smoke Detector.

The SD-16 Series Smoke Detector includes following models, the models differ in battery used.

SD-16ZBS

SD-16SL-ZBS

Parts Identification

1. Red LED

- Continuous quick flashes

The Smoke Detector is alarming.

- Two quick flashes

The Smoke Detector has successfully joined a ZigBee network after

factory reset.

- Flashes once every 20 minutes:

The Smoke Detector has lost connection to its current ZigBee

network.

- Flashes every 4 seconds:

Battery Exhausted

- Flashes every 2 seconds:

The Smoke Detector is under warm-up and self-calibration process

- Flashes every second:

The Smoke Detector is in Alarm Silence mode.

2. Amber LED

- Flashes every 4 seconds:

Battery Exhausted

- Flashes every 5 seconds:

Auto-calibration has failed.

3. Function Button

- Press the button once to send a supervision signal / test Smoke

Detector

- Press the button once during alarm to silence the alarm.

- Press and hold the button for 10 seconds then release to reset the

Smoke Detector.

- Press and hold the button for 20 seconds then release to recalibrate

the Smoke Detector.

4. Buzzer

5. Mounting Hole

The Hook of the Mounting Bracket can hook into this Mounting Hole.

6. Battery compartment

The battery used varies according to Smoke Detector model number.

7. Battery Compartment Cover

8. Mounting Bracket

Features

Smoke Detection

The Smoke Detector will be activated whenever the smoke concentration exceeds the detection

threshold. After activation, the Red LED will flash quickly and the Smoke Detector will transmit

alarm signal and raise alarm with its built in buzzer for 8 seconds. The alarm sound will repeat in

pattern of 2-second alarm and 1-second pause.

The Smoke Detector will check smoke concentration every 8 seconds, if the smoke

concentration still exceeds detection threshold after 8 seconds, the buzzer will continue to

sound alarm and the LED will continue to flash.

If the smoke concentration remains above the detection threshold, the Smoke Detector will

continue to send the alarm signal every 2 minutes.

If the smoke concentration drops below detection threshold, the Smoke Detector will stop

alarming immediately, a restore signal will be transmitted if no alarm is activated again for 160

seconds.

Alarm Silence

When the Smoke Detector is alarming, you can press the Function button once on Smoke

Detector to transmit a cancel signal and enter Alarm Silence mode for 10 minutes

Under Alarm Silence mode, the Smoke Detector will not sound alarm; the LED Indicator will

flash every second to indicate it is under Alarm Silence mode.

After 10 minutes, if the smoke concentration still exceeds detection threshold, the Smoke

Detector will raise alarm and send alarm signal again.

Recalibration

The Smoke Detector will calibrate its sensor every time when power is applied to ensure optimal

smoke sensitivity. After installation, the operation condition of the Smoke Detector may vary after

some time, which may affect its smoke detection function and requires recalibration. There are two

ways to recalibrate the Smoke Detector: auto calibration and manual calibration.

Auto Calibration:

After power up, the Smoke Detector will perform auto-calibration after 4 hours.

After the first auto-calibration, the Smoke Detector will perform auto calibration every month.

During the auto-calibration process, the Smoke Detector will not emit any sound.

If auto-calibration fails the LED will flash rapidly and the Smoke Detector will send a calibration

fail signal to the ZigBee Network coordinator. To stop the LED from flashing, remove and reload

the batteries or start a new calibration process manually. If the manual calibration fails again,

Smoke Detector will emit continuous beeps. To stop the beeping sound and the flashing LED,

remove and reload the batteries.

When Smoke Detector auto calibration fails, the smoke alarm function will still work normally

using the threshold value taken from the last successful calibration.

Manual Calibration:

Manual calibration can be performed any time as desired:

1. Press and hold the function button for 20 seconds.

2. The Smoke Detector will emit 2 short beeps at after 10 seconds and 3 short beeps after 20

seconds. Keep holding the function button and release until you hear the 3 short beeps after 20

seconds.

3. The Smoke Detector will enter calibration process. The LED Indicator will flash every 2 seconds.

4. After the Smoke Detector finishes recalibration, it will emit two quick beeps to indicate. The LED

will turn off.

5. If calibration process fails, Smoke Detector will emit alarm sound. Please remove and reinsert

battery to restart process again.

Battery and Low Battery Detection

The battery used varies according to Smoke Detector model number.

Model Number Battery

SD-16-ZBS 2 AAAlkaline 1.5V Batteries

SD-16SL-ZBS 1 CR123A 3V Lithium Battery

The Smoke Detector feature Low Battery Detection function. When the battery voltage is low,

the Smoke Detector will transmit Low Battery signal to the coordinator in ZigBee network.

If batteries are not changed after low battery, the Smoke Detector will stop all function when

batteries are exhausted and flash both LEDs every 4 seconds to indicate failure.

When changing batteries, after removing the old batteries, press the Function Button twice to

fully discharge before inserting new batteries.

Supervision

The Smoke Detector will transmit a supervision signal to report its condition regularly according to

user setting. The factory default interval is 30 minutes. The user can also press the Function Button

once to transmit a supervision signal manually.

Test Smoke Detector

Press the Function button once during normal operation to test if Smoke Detector is functioning

normally.

If the Smoke Detector functions normally, the Red LED will turn on briefly and sound a

2-tone beep.

If the buzzer sounds 2-tone beeps 3 times, the “Optical Chamber” on the Smoke Detector

is either dirty or out-of-order.

If the Red LED doesn’t light up and no beep is sounded, it means the Smoke Detector is

out-of-order.

ZigBee Network Setup

ZigBee Device Guideline

ZigBee is a wireless communication protocol that is reliable and has low power consumption and

high transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of

devices to be included in a network and coordinated for data exchange and signal transmission.

Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join

network after powering on. Since performing a task in connecting network may consume some

power, it is required to follow the instructions to avoid draining battery of a ZigBee device

- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the

ZigBee device.

- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee

device is in use.

- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing

the battery from a ZigBee device.

Joining the ZigBee Network

As a ZigBee device, the Smoke Detector needs to join a ZigBee network to transmit signal when

smoke concentration is detected. Please follow the steps bellow to join the Smoke Detector into

ZigBee network.

1. Insert the batteries into the battery compartment to power on the Smoke Detector.

2. The Smoke Detector will emit two short beeps, and then begin warm up for 1minute, the LED will

flash every 2 seconds.

3. Joining ZigBee network is allowed during the 1-minute warm up period. Press and hold the

function button for 10 seconds and release to search for existing ZigBee network. Please make

sure the permit-to-join feature on the router or coordinator of your ZigBee network is enabled.

4. After joining the ZigBee network, the Smoke Detector will be registered in the network

automatically. Please check the ZigBee coordinator, security system control panel or CIE (Control

and Indicating Equipment) to confirm if joining and registration is successful.

5. After the 1-minute warm up period expires, the Smoke Detector will emit a beep to indicate it now

enters calibration process. The calibration process takes 2~7 minutes; the LED will continue to

flash during calibration. Joining ZigBee network is prohibited during calibration process.

6. When calibration is complete, the Smoke Detector will emit 2 beeps and LED will stop flashing to

indicate it is now under normal operation. If calibration fails, the Smoke Detector will sound

continuous beep.

7. Under normal operation, if the Smoke Detector loses connection to its current ZigBee network,

the LED indicator will flash every 20 minutes to indicate the situation. Please check your ZigBee

network condition and Smoke Detector signal range to correct the situation.

Removing Device from ZigBee Network (Factory Reset)

To remove the Smoke Detector from current ZigBee network, the Smoke Detector must be put to

Factory Reset to complete device removal. Factory Reset function will clear the Smoke Detector of

its stored setting and information and prompt the Smoke Detector to search for new ZigBee network.

Before removing device, make sure the Smoke Detector is within current ZigBee network

signal range

1. Press and hold the function button for 10 seconds, then release the button to reset Smoke

Detector.

2. Upon reset, the Smoke Detector will clear current ZigBee network setting and transmit signal to

ZigBee coordinator to remove itself from current ZigBee network. It will then actively search for

available ZigBee network again and join the network automatically.

Factory Reset

If you want to remove the Smoke Detector from current network and join a new network, you need to

use the Factory Reset function to clear the Smoke Detector of its stored setting and information first

before it can join another network. To perform Factory Reset:

1. Press and hold the function button for 10 seconds, release the button upon hearing two short

beeps.

2. The Smoke Detector has been reset to factory default setting with all its previous network

information removed. It will now actively search for available ZigBee network again and join the

network automatically.

3. If the Smoke Detector successfully joins a ZigBee network, the LED Indicator will flash twice to

indicate.

Installation

Installation Guideline

It is recommended to install the Smoke Detector at the center of the ceiling, or top of stairwell

with at least 60 cm of space between the Smoke Detector and the wall

Do not install the Smoke Detector in the following locations:

The Kitchen – Smoke from cooking might cause an unwanted alarm.

Near a ventilating fan, florescent lamp or air-conditioning equipment – air drafts from

them may affect the sensitivity of the detector.

Near ceiling beams or over a cabinet – stagnant air in these areas may affect the

sensitivity of the detector.

In the peak of an “A” frame type of ceiling.

Mounting the Smoke Detector

The Smoke Detector has a mounting bracket for mounting on ceiling.

1. Use the mounting bracket as template to mark the two holes on ceiling for installing screws.

2. Screw the mounting bracket onto the ceiling according to marked location. Install wall plugs if

necessary.

3. Locate the hooks of the mounting bracket and line up the hooks with the mounting holes on the

Smoke Detector. Fit the hooks into the mounting holes, then rotate the Smoke Detector

counter-clockwise to lock it into the mounting bracket. Mounting the Smoke Detector is now

complete.

Using Smoke Detector with ZigBee Router

IMPORTANT NOTE

If the Smoke Detector installation location is away from your system control panel and requires

ZigBee routers to improve signal strength. DO NOT use a ZigBee Router without backup battery. A

ZigBee router without battery will be powered down during AC power failure and the Smoke

Detector connected to the router will lose connection with ZigBee network. You should plan your

Smoke Detector installation location using only ZigBee router with backup battery.

Maintenance

The top cover and the smoke detecting chamber can be detached from the Smoke Detector for

maintenance. Follow the steps below to maintain the smoke detecting chamber:

1.Remove the top cover by rotating the top cover counter-clockwise, then remove the smoke

detecting chamber

2.Pull out the anti-insect mesh inside the chamber and clean the chamber and mesh with a brush or

water.

3.Re-insert the anti-insect mesh into the chamber and insert the chamber back onto the Smoke

Detector. Please make sure the chamber is dry before re-inserting back onto the Smoke Detector.

4.Insert the top cover back onto the Smoke Detector. The top cover includes 3 insertion hooks to fit

into the Smoke Detector. Each hook has a number next to it. Match these numbers with the

numbers of insertion holes on the Smoke Detector.

Appendix (For developers only)

Smoke Detector Cluster ID

Device ID: IAS Zone 0x402

Endpoint: 0x01

Server Side Client Side

Mandatory

Basic (0x0000) None

Identify(0x0003)

IAS Zone(0x0500)

Optional

None None

Attribute of Basic Cluster Information

Identifier Name Type Range Access Default

Mandatory

/ Optional

0x0000 ZCLVersion Unsigned 8-bit

integer 0x00 –0xff Read

only 0x01 M

0x0001 ApplicationVersion

Unsigned 8-bit

integer 0x00 –0xff Read

only 0x00 O

0x0003 HWVersion Unsigned 8-bit

integer 0x00 –0xff Read

only 0 O

0x0004 ManufacturerName Character

String 0 – 32 bytes Read

only Climax

Technology O

0x0005 ModelIdentifier Character

String 0 – 32 bytes Read

only (Model Version) O

0x0006 DateCode Character

String 0 – 16 bytes Read

only O

0x0007 PowerSource 8-bit 0x00 –0xff

Read

only M

0x0010 LocationDescription Character

String 0 – 32 bytes Read /

Write O

0x0011 PhysicalEnvironment 8-bit 0x00 –0xff

Read /

Write 0x00 O

0x0012 DeviceEnabled Boolean 0x00 –0x01

Read /

Write 0x01 M

Attribute of Identify Cluster Information

Identifier Name Type Range Access Default

Mandatory

/ Optional

0x0000 IdentifyTime Unsigned

16-bit integer 0x00 –0xffff Read /

Write 0x0000 M

Attribute of IAS Zone Cluster Information

Identifier Name Type Range Access Default

Mandatory

/ Optional

0x0001 ZoneState 8-bit

Enumeration All Read

only 0x00 M

0x0002 ZoneType 8-bit

Enumeration All Read

only M

0x0003 ZoneStatus 16-bit bitmap All Read

only 0x00 M

0x0010 IAS_CIE_ADDRESS IEEE

ADDRESS Valid 64bit

IEEE address Read /

Write M

0x0011 ZONE_ID Unsigned 8-bit

integer All Read

only 0xFF M

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications

not expressly approved by the party responsible for compliance could void the

user's authority to operate this equipment. (Example - use only shielded

interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with a minimum distance of 20 centimeters between the radiator and your

body.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be

co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Climax Rauchmelder Handbücher

Climax

Climax SD-8ZBS-EL Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung