Clipper HHD323 Bedienungsanleitung

OWNERS

MANUAL

Handheld Drill

MODEL:

HHD323

FORM <<HHD323 rev 10/2009

WARRANTY

Norton warrants all products manufactured by it against defects in

workmanship or materials for a period of one (1) year from the date of

shipment to the customer.

The responsibility of Norton under this warranty is limited to

replacement or repair of defective parts at Norton's Stephenville,

Texas factory, or at a point designated by it, of such part as shall

appear to us upon inspection at such point, to have been defective in

material or workmanship, with expense for transportation borne by the

customer.

In no event shall Norton be liable for consequential or incidental

damages arising out of the failure of any product to operate properly.

Integral units such as gasoline engines, electric motors,batteries,

tires, transmissions, etc., are excluded from this warranty and are

subject to the prime manufacturer's warranty.

This warranty is in lieu of all other warranties, expressed or implied,

and all such other warranties are hereby disclaimed.

Important: Before placing equipment in operation, record the following

information.

MODEL:_________ SERIAL NO.___________

PURCHASE FROM: _____________________

ADDRESS: ____________________________

CITY_______ STATE ______ ZIP ________

TELEPHONE NO. ______________________

Before using this equipment, make sure that person using it

read and understand the instructions in this owner’s manual.

Table Of Contents

CONTENTS PAGE

I. Preparation

A. Safety Precautions 4-6

B. Assembly 7

C. Specifications 7

D. Electrical Supply 8-10

F. Generator 8

G. Grounding Instructions 8

H. Electrical Connections 8-10

II. Operation

A. Core Bit Installation 10-11

B. Water Supply 11

C. Drilling Operation 11-12

D. Hand Held Drilling Technique 12-13

III. Component Description

A. Diagram 14

IV. Parts List Section

A. Ordering Information 15

B. HHD323 Exploded View Parts Drawing 16

C. HHD323 Parts Listing 17-18

Read Owners Manual Before Use

Safety Alert Symbol: Information Following This Symbol Is Very

Important.

I. PREPARATION

A. Safety Precautions

Important! The following safety precautions must always be observed.

Hazard Symbols

Fuel (gasoline) is extremely flammable and its vapors can

explode if ignited. Store gasoline only in approved

containers, in well-ventilated, unoccupied approved

areas, and away from sparks or flames. Do not fill the

fuel tank while the engine is hot or running. Do not

start the engine near spilled fuel. Never use the fuel as a cleaning

agent.

Engine components can get extremely hot from operation. To

prevent burns, do not touch the engine or related parts while the

engine is running or immediately after it is turned off. Never operate

the engine with any heat shields or guards removed.

Keep all guards in place when operating any piece of equipment

Keep hands, feet, hair, and clothing away from all rotating parts

Lethal Exhaust Gas use only in well ventilated areas. Engine

exhaust gases contain poisonous carbon monoxide, which is

orderless, colorless, and can cause death if inhaled. Avoid inhaling

exhaust fumes, and never run the engine in a closed building or

confined area

Never tamper with the governor components of settings to increase

the maximum speed. Severe personal injury and damage to the

engine or equipment can result if operated at speed above

maximum. Always obey the maximum speed rating of blade.

Dust and Silica Warning

Grinding/cutting/drilling of masonry, concrete, metal and other materials can

generate dust, mists and fumes containing chemicals known to cause serious or

fatal injury or illness, such as respiratory disease, cancer, birth defects or other

reproductive harm. If you are unfamiliar with the risks associated with the

particular process and/or material being cut or the composition of the tool being

used, review the material safety data sheet and/or consult your employer, the

material manufacturer/supplier, governmental agencies such as OSHA and

NIOSH and other sources on hazardous materials and make certain to comply

with all product warnings and instructions for the safe and effective use of the

material being cut. California and some other authorities, for instance, have

published lists of substances known to cause cancer, reproductive toxicity, or

other harmful effects.

Control dust, mist and fumes at the source where possible. In this regard use

good work practices and follow the recommendations of the manufacturer/supplier,

OSHA/NIOSH, and occupational and trade associations. Water should be used

for dust suppression when wet cutting is feasible. When the hazards from

inhalation of dust, mists and fumes cannot be eliminated through engineering

controls such as vacuum and/or water mist, the operator and any bystanders

should always wear a respirator approved by NIOSH/MSHA for the material being

cut.

Use Approved:

Eye Protection Hearing

Protection Respiratory

Protection Head Protection

1. Know your drilling machine! Read the Owner’s manual carefully. Learn

the operation, application and limitations, as well as the specific potential

hazards peculiar to this equipment.

2. NEVER connect the green [or green & yellow] wire to a live terminal.

3. Use only three-wire grounded extension cords suitable for use outdoors

and of sufficient gage to accommodate power requirements.

4. Replace frayed or damaged extension cords.

5. Keep the work area clean avoiding cluttered work areas.

6. Consider the work area environment!

- Do not expose power tools to rain.

- Wear rubber boots to further insulate yourself from the drill.

- Mop up all excessive water around the work area before and after

drilling.

- Keep the work area well lit.

7. Use extreme caution when drilling through floors. Provide for protection

of all personnel and material below the area. Cores generally drop from

the drill bit at the completion of the hole.

8. Keep visitors away. Do not let visitors contact tool or extension cord. All

visitors should be kept at a safe distance from the work area.

9. Do not force the bit into drilling surface.

10.Dress properly for the work being performed.

- Do not wear loose clothing or jewelry which can get caught in moving or

rotating parts.

11.Don’t abuse the cord. Never carry the tool by the cord or yank the cord to

disconnect the plug from the receptacle.

12.Don’t overreach! Keep proper footing and balance at all times. The

slippery surface created during the drilling operation results in unstable

footing.

13.ALWAYS disconnect the power before servicing or changing accessories

or bits.

14.ALWAYS check, then make sure wrenches are removed from the motor

spindle and bit adapter before connecting power or starting the drill

motor.

15.ALWAYS make sure power switch is in “off” position before connecting

drill to power.

16. Never drill by hand a bit that is over 4” (100 mm) in diameter. Use a drill

stand for bits over 4” (100 mm) in diameter.

You Are Responsible For Your Safety!!!

I. PREPARATION

B. Assembly

The HHD323 handheld drill is shipped completely assembled except for core

bit adapters, core bit, and the collar handle. Inspect the drill for shipping

damage. If any damage is found, contact the shipper immediately and file a

freight claim. Saint-Gobain Abrasives, Inc. is not responsible for any freight-

related damages.

Be sure you have the following items:

1. HHD323 handheld drill

2. 27mm Wrench

3. 12” Adjustable wrench

4. 5mm Allen wrench

5. Adapter M18 female to 5/8” male

6. Adapter M18 female to 1-1/4” male

7. Quick Detach Water Hose Adapters

8. Carrying case

Read and understand the remaining sections of this Owner's Manual.

C. Specifications

Dimensions/Weight

Length 18.11" (460 mm)

Width 4.33" (110 mm)

Height 9.84" (250 mm)

Weight 12.1 lbs

Engine

Engine Type Single Phase

Volt 115 v

Amp 12 amp

Demand 1350 w

RPM 0-2200 rpm

Bit Capacity 1” (25 mm) – 3” (76 mm)

D. Electrical Supply

The HHD323 handheld drill is furnished with a 115 volt, single phase motor.

This motor operates within a power range of 110 to 120 volts. Serious damage

can result if the supply line voltage does not fall within this range.

The following wire sizes are recommended when using an extension cord:

Wire Gauge (AWG) Length Of Wire

Number 14 25 Feet

Number 12 50 Feet

Number 10 75 Feet

Number 08 100 Feet

For Best performance use 50 feet of 10 gauge extension cord. All extension

cords must be one piece, free of any damage (frays, cracks, breaks, burn

marks, exposed wires, and loose ends).

F. Generator:

If a generator must be used, it must be of 4.1kW (4,100 W) or larger. The

generator must have a 15A circuit or greater and capable of providing a

minimum of 4.1kW at the required voltage. Under size generators will cause

motor damage and is not covered under warranty.

G. Grounding Instructions:

Grounding protects the operator from electric shock. At the time of delivery

of the motor is equipped with an approved three-conductor cord and three-

prong grounding type plug. The green (green/yellow in CEE-Versions)

conductor in the cord is the grounding wire. NOTE: Never connect the green

(green/yellow) ground conductor (wire) to a live terminal. In case of doubt

concerning the ground of the receptacle, call a qualified electrician and have it

checked for proper ground.

zBefore connecting the drill to the power source, make sure that the

voltage and cycles shown on the name plate of the motor are the same

as the available electrical power supplied.

zAlways properly ground the core drill before attempting to start the

motor. The presence of water during the drilling operation requires that

the drill always be properly grounded.

zNEVER connect the green (ground) wire to a live terminal!

H. Electrical Connections:

The installation of cables, plugs, and switches must be made ONLY by an

authorized electrician. All installations must be made according to the local

regulations for electrical equipment. All components must meet local

requirements. For additional information see the National Electrical Code

(NEC) for the United States and Canadian Electrical Code for Canada.

The use of a 3-prong adapter is prohibited in Canada by the Canadian

Electrical Code.

Fig. A shows a standard NEMA 5-15 plug (male) and receptacle (female),

which should be used with the HHD323 Hand Held Core Drill. If the electrical

receptacle has two (2) conductors as shown in Fig. B an adapter is available

from a local electrical supplier for connecting the NEMA 5-15 plug to an NEMA

1-15. When using a NEMA 1-15 two prong receptacles the green grounding

ear extending from adapter must be connected to a permanent ground. No

adapter is available for Fig. C plugs as this is a 230v receptacle.

To connect twist lock plugs like those shown in figures D and E, insert the plug

into a matching outlet. When the plug is fully inserted, turn it clockwise until it

locks. This prevents the plug from being pulled out accidentally. To remove

the plug, twist it counterclockwise to unlock it and remove it from the outlet.

Adapters are available from a local electrical suppler to convert a NEMA 5-15

plug to a twist lock.

NOTE: RECEPTACLE MUST BE GROUNDED FOR SAFE USE OF

ADAPTER:

IF IN DOUBT CALL A QUALIFIED ELECTRICIAN AND HAVE THE

RECEPTACLE CHECKED FOR GROUND

•For Additional Safety Use A Ground Fault-Interrupter (GFCI ) Device.

•Do Not Use The Drill In Inflammable, Gaseous, Or Explosive Atmosphere

•Do Not Expose The Drill Motor To Rain Or Use In Damp Or Wet Locations

•Do Not Abuse The Cord, Or Carry Or Lift The Motor By The Cord

•Keep The Power Supply Cord Away From Humidity And Water

•Make Sure That The ON/OFF Switch Is In The “OFF” Position Before Plugging

Into A Power Supply

•Unplug The Drill Before Changing A Drill Bit

•Unplug The Power Cord When Attaching The Water Supply, Also Turn The

Water Valve To The “Off” Position Before Attaching

•Do Not Use If Parts Of The Motor Housing Are Missing Or Damaged

•Do Not Use If The Power Cable Or Extension Cable Is Damaged

•Do Not Make Any Attachments, Adjustments, Or Accessory Changes With The

Unit Plugged In

•Always Use The Proper Length/AWG For Extension Cords (See The Section

Titled Electrical Supply)

♦If Water Comes Out Of The Over Flow Bore (Item 3) Stop The Drill Operation

And Replace The Water Ring Seal Immediately

♦DO NOT Use Or Reuse Waste Water. Dirt And Slurry May Damage The Ring

Seals

•Prevent Water From Spraying On Any Part Of The Electrical Motor Or Cables

II. OPERATION

A. Core Bit Installation

Adapters are needed to install specific sized core bits.

1. Using a wrench to firmly hold the output shaft, screw the core bit onto the

spindle until snug.

Inhaltsverzeichnis

Andere Clipper Bohren Handbücher

Clipper

Clipper NORTON CDM 204 Bedienungsanleitung

Beliebte Bohren Handbücher anderer Marken

Makita

Makita BDF456 Bedienungsanleitung

Black & Decker

Black & Decker LDX220 Bedienungsanleitung

Hitachi

Hitachi DH 40MA Bedienungsanleitung

Challenge

Challenge JO Technisches Referenzhandbuch

Makita

Makita LXFD01 Bedienungsanleitung

Festool

Festool T18+3 Bedienungsanleitung

Milwaukee

Milwaukee M12 FPDX-202X Bedienungsanleitung

EINHELL

EINHELL TE-RH 32 E Bedienungsanleitung

Makita

Makita DHP484 Bedienungsanleitung

Makita

Makita FD05 Bedienungsanleitung

Bosch

Bosch PSB 530 RA Bedienungsanleitung

Maximum

Maximum 054-1359-4 Bedienungsanleitung

Makita

Makita HP332D Bedienungsanleitung

Raider

Raider RDP-HD31H Bedienungsanleitung

Bort

Bort BPM-1400x2 Bedienungsanleitung

Black & Decker

Black & Decker 7266 Bedienungsanleitung

KENT USA

KENT USA TRD1230 Bedienungsanleitung

Bosch

Bosch GSB 19-2 RE Bedienungsanleitung