Closet Maid ShelfTrack Montageanleitung

ShelfTrack ®

Installation Tips

/18

Tools you will need for assembly:

.50 in.

.25 in.

PARTS

3/16 in. Toggle / 3 in. Bolt #12 x 2 in. Panhead Screw 1/4 in. Anchor

Shelf Caps Closet Rod Cap Shoe Shelf Support and Inserts

Closet Rod Support Shelf Bracket Hang Track

Standard

Closet Rod

1Prepare for hang track installation

A) CUT TRACK IF NECESSARY

Remember to always cut between the holes.

B) DETERMINE WALL TYPE

Determine whether you will be mounting the hang track (and standards) into drywall or

concrete. (Note: Drywall installation requires mounting to at least one stud.)

The installation is in a later step, but it is important to understand which method you will

use.

C) DETERMINE PROPER HARDWARE FOR WALL TYPE

Locate and identify proper hardware for your wall type.

THROUGH DRYWALL

INTO STUD

DRYWALL

USE ANCHOR/SCREW FOR ALL HOLES

CONCRETE

Mark the Hang Track Location on closet wall

A) DETERMINE “TOP” AND “BOTTOM”

OF HANG TRACKS

B) DRAW A LEVEL LINE 7 ft. UP FROM

THE FLOOR

Place BOTTOM edge of hang track ON MARKED

LINE and AGAINST EACH SIDE WALL in closet.

Mark all the hole locations on wall.

(NOTE FOR DRYWALL INSTALLATION: Be sure

at leaset one hole aligns with a stud.)

3Attach Hang Track to wall using specic hardware

A) DRYWALL

Drywall installations require at least

one hole to align with a stud (see

diagram).

For holes which go ONLY into

drywall, drill 1/2 in. holes and use

3/16 in. toggle/bolt**.

For hole(s) which align with stud(s),

use #12 x 2 in. panhead screw

directly into stud (do not predrill hole).

B) CONCRETE

For ALL holes, drill a 1/4 in. hole and

insert an anchor.

Thread a screw through track and into

each anchor.

** Insert bolt through hole in hang track and re-install toggle onto end of bolt. Repeat for all

toggles and bolts. Place hang track against wall at the hole locations. Squeeze toggle bolts

and push through drilled holes. Tighten bolts to secure hang track to wall.

A) Space standards NO MORE than 24 in. apart and a MINIMUM of 2 in. in from end of hang

track. Measure from the CENTER of one standard to the CENTER of the next standard.

B) Attach standards as shown in locations marked for

your wall width. Be sure to measure from center

of one standard to center of next standard. Never

place standards more than 24 in. apart, less than

2 in. from end of hang track, or more than 4 in.

from from end of hang track (for standards closest

to side walls).

Secure each standard to wall through second or

third hole location with one supplied screw/anchor.

To do so, drill 1/4 in. holes at hole locations,

insert anchor, and attach standard to wall with 2 in.

screw.

Install standards onto hang track

Install brackets

Insert shelf brackets into standards at desired height for

each shelf.

Each 8 ft. shelf requires 5 shelf brackets.

Each 6 ft. shelf requires 4 shelf brackets.

Each 4 ft. shelf requires 3 shelf brackets.

Each 2 ft. shelf (or cut 1 ft. shelves) require 2 shelf

brackets.

Install shelves

A) Allow a 1 in. - 2 in. overhang (beyond bracket). Never allow more than a 4 in. overhang.

B) FOR SHELVES THAT

REQUIRE CUTTING:

Put shelf on brackets so one side is

ush with wall.

Allow an equal overhang (from

brackets) on both sides. Measure

amount to be cut.

Remove shelf and cut with hacksaw

or bolt cutter.

Do not make cuts where vertical

spacers are on front lip of shelf.

C) Place shelf caps onto exposed shelf

wires.

6Install shelves (Cont.)

Install shoe shelf

Rest shelf on each shelf bracket at desired

location.

Pull shelf forward and allow front to “drop”

over nose of shelf brackets (nose of each shelf

bracket will t between wires).

Push shelf backwards so back wire ts into

shelf bracket slots.

Firmly pull shelf forward at each bracket

location to lock shelf into place.

Install shoe shelf

A) Attach insert onto end of shoe shelf support

as shown.

B) Attach shoe shelf supports to

longest standards at bottom

right.

NOTE: For proper installation, turn

shoe shelf upside down so lip faces

up before installing.

• Attach shoe shelf onto shoe shelf

supports by placing back of shelf into

slots at back of shoe shelf

support. Pull shelf forward and lower

front of shelf onto shoe shelf support.

Insert as shown.

Inhaltsverzeichnis

Andere Closet Maid Lagerung Handbücher

Closet Maid

Closet Maid 432600 Bedienungsanleitung

Closet Maid

Closet Maid SuperSlide 5637 Bedienungsanleitung

Closet Maid

Closet Maid 3120 Montageanleitung

Closet Maid

Closet Maid 2-Door Versa Cabinet 12075 Bedienungsanleitung

Closet Maid

Closet Maid 6-Cube Storage System Bedienungsanleitung

Closet Maid

Closet Maid 3-Cube Storage System 8178 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung