Cloudray MP Pro Series Bedienungsanleitung
Laser Machine
Troubleshooting
Guide
Cloudray Laser
THE PDF TROUBLESHOOTING GUIDES REPRESENT SOME OF THE MORE
COMMON QUESTIONS OR ISSUES THAT YOU MAY ENCOUNTER WITH
CLOUDRAY LASER. THE PDFS ARE LAID OUT IN A STEP-BY-STEP FASHION
WITH SUPPLEMENTARY LINKS TO RELEVANT BOSS YOUTUBE VIDEOS. IF
YOU THINK YOU NEED FURTHER HELP CONTACT US:
1.Laser Engraving Machine Type
2.Installation and driver
3.Software: Ezcad2/3 & Lightburn
4.Red Light Settings
5.F-theta Lens
6.Foot switch
1.Laser Engraving Machine Type
MP-60 LiteMarker 60W Split Laser Engraver Marking Machine
MP-60 comes with 800mm manual lifting tower, which supports max
scan fields
≤
300*300mm.
This unit comes with EZCAD2/EZCAD2 Lite software, which is compatible
with Lighbturn software
(Pro) MP Series-Auto Focus 60W Laser Engraver Marking Machine
(Pro)MP-60 comes with 500mm electric lifting tower(with motor), which
supports scan fields
≤
200*200mm. This unit comes with
EZCAD2/EZCAD2 Lite software, which is compatible with Lighbturn
software
Autofocus, free your hands, can realize high speed, marking, and high
precision. Before marking job, system senses the height of the work and
adjusts the height of the galvo head automatically using the electric lift
column. But It will not adjust automatically while engraving. The auto-
focus galvanometer only focuses once before processing, and will not
focus in real time during processing.
AR-60 60W Split Laser Engraver 2.5D Fiber Marking Machine
AR-60comes with 500mm electric lifting tower(with motor), which
supports scan fields
≤
200*200mm.
This unit comes with EZCAD3 software,Can be used with Z-axis auto
focus to achieve 2.5D engraving.
2.Installation and driver problems
A short circuit was caused when the machine was installed
Unplug the power cable, ensure the machine is powered off, open the
upper and side cover of the chassis (Remove three hexagonal screws at the
front and back)
1. Check whether switching power supply for the galvo head is 90-264V(the
left-most one), and the 24V switching power supply is at 115V
2. Check whether the wires at the back end of the button is broken, touched
with the metal of the chassis or burnt.
Yellow Exclamation Mark Issue in
Device Manager
"Failed to open lmc device" error
Please confirm whether you installed the
driver software which is in the U disk.(The
compressed file in the U disk is a backup
file, which can be decompressed and used
when the original folder is damaged.)
Check whether there is a yellow
Exclamation Mark Issue in Device Manager.
If yes, that means that you installed wrong
driver. Please uninstall the current V2 or V4
driver and reinstall another V2 or V4 driver.
Uninstall the installation video of the driver:
https://youtu.be/jHvBR4P0T9g
2.Installation and driver problems
“error code 52”
After doing uninstall the driver & install
the driver, it is recommended to restart
the computer to see if the driver is
normal. If the issue is not fixed, please
show us related pictures or videos for us
to check If still not work, Would you
please record a video for us to check or
help us judge where the problem is?
More details concerning the technology
problem when you use the product will
be useful too.
3.Software: Ezcad2/3 & Lightburn
Lightburn
Does Cloudray marking machine support lightburn?
At this time, only devices that are supported by EzCad2 or EzCad2 Lite
software will work with LightBurn and only those that connect to a computer
over USB. Raycus, JPT, IPG, and Max Photonics fiber sources, as well as CO2
laser sources are supported. (Max Photonics are JPT compatible
）
Does Lightburn offer a free trial?
30-day free trial
Laser display "Disconnected" alarm
1. Shift-click the ‘Devices’ button in the ‘Laser’ window, you force LightBurn
to re-establish communications with your device.
2.Try rebooting Lightburn, disconnecting and reconnecting Cloudray laser,
shift click on Device, tried reloading Device, rebooting your lap top, Com
port is selected.
3. Do you have multiple copies of LightBurn running, maybe? Or any other
software that might be holding on to your COM port? Try bringing up the
task manager (Ctrl+Shift+Esc) and seeing if anything is running that you
don’t expect, or a hung copy of LightBurn running in the background.
Can use the EzCad2 software but can't
get the Lightburn software
Software driver maybe wrong. Ezcad2
and Lightburn software have different
drivers. If using lightburn software, you
have to install Ezcad2 driver(Used by
galvos), please check attached picture as
referenced. Only one driver can be
installed on a computer.
3.Software: Ezcad2/3 & Lightburn
Ezcad2
What's wrong with the prompt "can not open correct file" after
opening the Ezcad?
It is because there is no correction
file and the “Use the correction
file” in the F3 parameter is
checked. If there is a correction
file, please select the correct path;
if there is no one, you can leave
“Use the correction file”
unchecked.
How to solve the problem that the line are not straight when marking
the grid?
There may be a coordinate problem with
the galvo correction.
How to set to repeat marking twice by pressing F2 once?
Because it is a 20W laser marking machine, it is a little bit not clear enough,
so I will mark twice. But I have to press F2 twice every time. Is there a setting
method that it will automatically mark twice by pressing it directly?
If the power is not enough, you can increase the frequency and reduce the
speed to increase the depth of marking.
If it is essential to mark twice at a time, you can check key F3 Parameters –
Other – Auto reset mark count, and exit to change the Total number to 2 in
the marking column.
3.Software: Ezcad2/3 & Lightburn
Ezcad2
After the driver is installed, the ezcad software still prompts that the
dongle can't be found?
Win10 64-bit, the driver installation has been displayed, but the software
prompts that the dongle cannot be found, what should I do?
First, the marking board does not require an external dongle. Then check
the followings:
1. There is a mismatch between the driver, board, and software. Try
changing the software version.
2. Check whether the marking board is genuine and whether its specific
model supports the corresponding computer system.
3. After confirming that the laser has been started, check whether the
connection between the laser and the board is loose or not in good contact.
Or just try another wire.
The image or text inversion problem of fiber laser marking machine
Just click on the parameter
settings (F3) and select "Galvo 2"
Tips
：
Regarding the common problems of Ezcad2, most problems can
be solved by reinstalling software and drivers.
3.Software: Ezcad2/3 & Lightburn
Ezcad3
“Ezcad3 software licenses invalid”
“The correct file format is error!”
Please download the correct file:
https://cdn.shopify.com/s/files/1/2222/7859/files/COR.rar?v 1671441314
Reference video:
https://youtu.be/NOL6BGlKJEs
The authorization code is as shown on the USB flash drive (for reference only)
4.Red Light Settings
Red light preview outline lost, or it doesn’t have the red light contour
Red light pointer settings
Justcheck this button "Show contour"
1. Click the parameter button (F3)
2. Select "other"
3. Select "Red Light pointer"
4. Select "Enable always show"
5. Please confirm the save operation
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cloudray Graveur Handbücher
