Clover Systems DR110 Bedienungsanleitung

Electronic Dynamo Regulator

INSTRUCTION MANUAL

DR110 Instruction Manual Pg. 1

INTRODUCTION

The Clover Systems DR110 is an all-

electronic voltage and current

regulator for DC generators used in

vintage cars, trucks, motorcycles,

tractors and boats. This regulator

never requires cleaning or adjustment,

and will be trouble-free for the life of

your vehicle. It is more efficient than

mechanical regulators, and is

impervious to shock and vibration,

INSTALLATION

1) First, be sure that you have the correct model DR110 for your vehicle

(Positive or Negative Earth, 6, 12, or 24 volts, A-circuit or B-circuit and

correct current limit to match your dynamo). Although DR110 is protected

against most every possible problem, it is possible to damage the unit and/or

your generator if for instance, the battery is hooked up backward (see

below).

2) You should make sure that the dynamo is in good working order before

installing the new regulator. If there is a problem with the dynamo, the

regulator could be damaged.

If you are installing a new generator, or your existing one is in unknown

condition, you can perform some

simple tests to verify that it is

workable:

a. With an ohm-meter, you

should measure resistance of ~

2 ohms from terminal D to

ground. If the resistance is

infinite, then either the wire

from D to the generator is not

connected, or the generator’s

armature is open.

b. Similarly, you should measure

resistance of ~ 5-6 ohms from

terminal F to ground. Infinite

resistance indicates the wire from terminal F to the generator’s field

coil is not connected, or the field coils are open. A low resistance

indicates partial shorting of the field coils to ground.

Figure 2 - Connections

Figure

–

With Delco Cover

DR110 Instruction Manual Pg. 2

3) Disconnect the battery ground cable to prevent any mishaps.

4) Next, label all wires connected to your existing regulator. If you do not

already have a regulator connected, you may need to trace the wires to see

exactly where they go.

5) Wire Connections: The connectors are labeled D (Dynamo Armature), F

(Field Coil), and B (Battery). Attach the wires to the DR110, and mount the

DR110 using the three stainless steel machine screws provided.

6) The DR110 is grounded to the chassis via the brass mounting spacers. Be

sure that a good ground connection is obtained, as the regulator will not

function properly if it is not grounded.

7) Reconnect the battery ground. If there is excessive sparking, there may be a

wiring mistake.

8) If everything seems to be in order, start the engine and observe the ammeter

and ignition warning light. If everything is working correctly, the warning

light should go out at around 800 RPM (depending on generator model).

You should also be able to see charging of the battery on the ammeter.

9) If there is no output from the generator, and it passed the above tests, see

the troubleshooting section in the appendix.

10) Installing the cover: DR110 does not include the

Delco/Autolite/Bosch/Ford metal cover. You can however, use your

existing cover, or find a used one. The original cover screws are sheet

metal screws. Do not use these; use the included #8 machine screws

instead. Some aftermarket covers have different dimensions from the

original covers and may require new holes.

Caution

Although the DR110 is protected against most everything that can go wrong,

there are some things that can damage the DR110 and/or your dynamo:

1) Connecting the battery backward. Be sure that you have the correct polarity

regulator. If there is any doubt, check the battery connections to see which

battery terminal is connected to the vehicle’s chassis.

2) Reversing the D and B wires will create a direct path from the battery to the

dynamo’s armature, which could damage your dynamo.

3) A-circuit regulators (Autolite, Bosch, Delco): If the F wire is shorted to

ground, the dynamo will run at full output without any voltage or current

limiting. As a result, your dynamo and wiring could be damaged.

B-circuit regulators (Ford & Lucas): If the F wire is shorted to the D wire

DR110 Instruction Manual Pg. 3

(dynamo armature), the dynamo will run at full output without any voltage

or current limiting.

4) If the ground wire is not connected to the regulator, the regulator will not

function correctly. The regulator ground is connected to the back plate, and

then to the vehicle’s chassis via the brass mounting spacer.

5) Note on Mounting: Mechanical regulators are typically mounted on rubber

bushings to provide some isolation from vibration and shock, but since

DR110 is immune to vibration and shock, the regulator can be rigidly

mounted.

DR110 Instruction Manual Pg. 4

TESTING & CALIBRATION

The DR110 voltage and current limits are set at the factory to match your

dynamo, and normally, no adjustment is required. You may however, wish to

confirm that everything is working properly, or change the settings to

accommodate your needs.

Both voltage and current limit are user adjustable. Voltage can be adjusted from

5v to 17v, and the current limit is adjustable from 7A to 30A. The HP version is

adjustable up to 55A.

Adjustment to the voltage or current limit must be carried out on the car. For

these adjustments, you will need an analog moving-coil voltmeter (0-20V)

and/or analog moving-coil ammeter (0-50A) plus a very small flat-blade

screwdriver.

Note: Use only analog moving-coil voltage and current meters for these tests.

Digital meters will not read correctly because of rapid variations and noise in the

dynamo output.

Voltage Limit Test (open circuit):

1) Remove the die-cast cover by removing the three screws from the back of

the unit:

Figure 3 - Cover Mounting Screws

2) Remove the wires from the B terminal. If there is more than one, connect

them together with a clip lead. This will provide power from the battery to

the vehicle’s electrical system so the engine can run.

DR110 Instruction Manual Pg. 5

3) Connect an analog voltmeter capable of measuring 0-20 volts between the B

terminal of the regulator and ground.

4) Now start the engine. As you increase the engine speed, you should see an

increase in the voltage on the meter. Run up the engine speed, and you

should see the voltage rise with engine RPM, until it reaches it’s preset limit

(See the Final Test Sheet at the end of this manual for the proper voltage).

5) If necessary, adjust the voltage limit control to get the desired output

voltage limit. Turn the pot clockwise to increase the limit, and counter-

clockwise to lower the voltage limit.

6) When finished, remove the voltmeter and re-attach the wires to the B

terminals.

Figure 4 – Location of Pots

The correct voltage limit also depends on they type of your battery. The

requirements for “flooded” type batteries, where you can add water are different

than for sealed, “Maintenance Free” batteries, also known as VRLA, AGM, or

Gel batteries, which require a lower charging voltage. The chart below shows

optimal settings for the two types of batteries, depending on the battery

temperature. For 6v applications, divide by 2.

We normally set the voltage at 14.3V at 25°C for 12v dynamos, and 7.2v for 6v

dynamos, which is safe for all batteries. Since there are many types and models

of batteries, you may wish to consult the battery specs for the optimum charging

voltage.

Voltage Adjust

Current Adjust

DR110 Instruction Manual Pg. 6

Voltage vs. Temperature

12.5

13.5

14.5

15.5

10 15 20 25 30 35 40

°C

Volts

Flooded

VRLA

Figure 5 - Voltage vs. Temperature

If the car has been running with substantial electrical load, the regulator may be

hotter than ambient temperature. Therefore, it is best to perform the test with the

regulator at ambient temperature.

Current Limit Test:

1) With the two B wires

disconnected from the

DR110, and connected

together, connect a 0-50A

ammeter between the B

terminal of the regulator

and the two B wires

connected together. If your

vehicle is negative ground,

then connect the + terminal

of the ammeter to the B

terminal of the regulator,

and the – terminal of the

ammeter to the two wires.

For positive ground, reverse

these connections.

2) Start the engine and turn on all loads such as headlights, fans, etc. As you

increase the engine RPM, you should see the current flow increase until it

reaches the preset limit. You may need to add additional loads to reach the

desired limit.

Figure 6 - Ammeter Hookup

DR110 Instruction Manual Pg. 7

3) Turning the pot clockwise increases the limit, and counter-clockwise

decreases the limit.

4) When finished, remove the ammeter and re-attach the wires to the B

terminals.

Warning: Do not adjust the current limit higher than the rated output of your

dynamo, as this may overload the generator and reduce it’s life.

Note: Typically, the ammeter in your vehicle only measures current to and

from the battery. It does not measure the total output of the generator, which

could be more. To measure total generator output, you need to connect an

ammeter as described above.

APPENDIX

How the regulator works

All generators work by rotating a loop of wire in a magnetic field. In a dynamo,

the magnetic field is created by electromagnets (field coils). Voltage and current

are controlled by adjusting the current to the field coils. The current through the

field coils determines the strength of the magnetic field that the armature rotates

in, and thus the output of the generator.

In the DR110, the output voltage of the generator is compared to a precision

voltage reference. When the generator output exceeds this reference, the current

to the field coils is cut off. This causes the generator output to fall. When the

output falls below the reference voltage, the field current is turned back on. In

this way, the field current is modulated at a rate of 50 – 125 Hz. These rapid

changes are smoothed out by the inductance of the field coils and armature, thus

maintaining a constant output voltage.

Current limiting is accomplished in the same way. Output current is sensed with

a Hall-Effect device that detects the magnetic field created by the output current.

When the output current exceeds a preset limit, the field current is turned off.

Just as with the voltage regulation, the field current is modulated to maintain a

constant output current.

Instead of a cut-out relay, DR110 uses a MOSFET “ideal diode”, which is much

more efficient than Schottky diodes. Power is supplied whenever the dynamo

output voltage is greater than the battery voltage, rather than a pre-set voltage as

in the mechanical regulator.

DR110 Instruction Manual Pg. 8

A-Circuit and B-Circuit

There are two types of shunt-wound dynamos:

A and B. The only difference is in the way

that the field coils are wired. In an A-circuit

dynamo, one end of the field coils is internally

connected to the dynamo output. In a B-circuit

dynamo, one end of the field coils is internally

connected to ground. So in the B-circuit case,

the regulator supplies current to the field coils,

and in the A-circuit, the regulator sinks current

from the field coils.

Ford and Lucas dynamos are B-circuit.

Autolite, Bosch, and Delco standard generators

used on autos are generally A-circuit, but there are some exceptions.

How to polarize a new generator

Your generator only needs to be polarized if it is new, has been rebuilt, or you

have changed ground polarity. A generator that has already been working does

not need to be polarized. Also, the Clover Systems regulator does not need to be

polarized, as there are no magnetic components.

A dynamo uses electromagnets to generate the magnetic field for the armature to

rotate in. But when starting up, there is no field current to create this magnetic

field. In order to get the process started, some permanent magnetism is required

to provide this field. This is provided by iron pole pieces that can be

permanently magnetized.

Magnetizing the pole pieces is easy, but is different for A-circuit and B-circuit

dynamos:

B-Circuit: While the car is not running, connect a lead from the battery to the

dynamo’s field coil terminal for one or two seconds. Connecting them for a

long period could overheat and damage the field coils.

A-Circuit: Disconnect the output wire from the dynamo (usually labeled D or

A). Then connect the field terminal of the dynamo (usually labeled F) to ground

with a jumper lead. Now using another jumper lead, briefly connect the battery

output to the dynamo output for a second. Connecting them for a long period

could overheat and damage the dynamo.

The pole pieces will now be permanently magnetized, and the dynamo will start

up. If the dynamo is properly polarized, it will produce ~3 volts with the field

coils disconnected.

Figure 7 - A and B circuits

DR110 Instruction Manual Pg. 9

Troubleshooting

In case there is no output from the dynamo, check the following:

1) D terminal is not connected to the dynamo output terminal

2) F terminal is not connected to the dynamo field terminal

3) Backplate is not connected to ground

4) Dynamo armature is shorted or open

5) Dynamo field coils are shorted or open

6) D, or F are shorted to ground

7) Dynamo is not polarized

8) Regulator is not the correct A or B circuit model

Service

If you need service or have questions, you can contact us at +1 949-598-0700 or

support@cloversystems.com.

Warranty

All Clover Systems products are guaranteed against original defects for one

year. Any products returned within the warranty period will be repaired or

replaced at no charge except for return shipping.

Inhaltsverzeichnis

Andere Clover Systems Controller Handbücher

Clover Systems

Clover Systems DR340 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung