CMP Panther 55-0027 Bedienungsanleitung
MODEL 55-0027
FIXED MOTOR BRACKET
INSTALLATION MANUAL
REV 12/15
CUSTOMER MUST RECEIVE THIS MANUAL AFTER INSTALLATION
1.604.940.2010 | sales@cmpgroup.net
INSTALLATION PROCEDURES
Congratulations, you have just purchased one of the finest outboard motor brackets available
today. With proper installation and care, this motor bracket will provide you with years of
trouble free use and performance.
Please take a few moments to review the information contained in the instructions to
familiarize yourself with the installation procedures suggested to successfully mount your new
motor bracket. Installation is easy particularly when you know each step ahead of time.
ASSEMBLY OF BRACKETS
The Model 55-0027 is designed so you can adjust the height of the bracket. Determine which
height adjustment best suits your needs and assemble according to the following instructions.
Step 1. Align the motor plate mounting holes to the height adjustment holes of the transom
plate. The motor plate has the Panther label. Make sure that the motor plate is attached
as shown in the picture. The picture shows the bracket fully extended.
Step 2. Put a washer onto a bolt and insert the bolt through the plates as shown in picture.
Install washer and nut on other end and hand tighten. Finish installing the remaining
bolts, washers, and nuts in the same manner. Securely tighten all bolts.
MOUNTING THE BRACKET TO THE BOAT
Place the assembled bracket on the desired location of your transom. Hold the bracket in place.
Make certain that the transom bracket is level. Mark at least two (2) upper and two (2) lower
hole locations using the transom plate as a template. Drill out the marks you just made using a
½” drill bit. Attach bracket to boat using appropriate length bolts, nuts, and washers.
Tighten securely.
**** Stainless Steel mounting hardware is recommended (not included). ****
HANGING THE MOTOR
Lift your motor onto the bracket. Position the plastic spacer block under the motor clamp
handles and against the lip of the bracket. Tighten securely.
12”
12”
9.5”
4” TYP.
2.750”
.750”
HOLE PATTERN, TRANSOM
SERVICE AND WARRANTY
Should your unit ever require service, please do not return the product to your dealer. Please call the number
below for special instructions on shipping and handling. Please call between 9:00 am - 5:00 pm (Pacic Time)
Monday through Friday. If service is required and covered by warranty, it will be repaired or replaced as
described below. If service is required and not covered by warranty, (such as damage caused from improper
trailering or from water intrusion through the breather tube), replacement parts are available for purchase
and may be paid for by Visa or MasterCard.
The warranty coverage on this equipment is limited to the terms set forth below:
CMP Group Ltd. warrants this product to be free of defects in material and workmanship for a period of ONE
(1) YEAR from the date of original retail purchase. Positive proof of date of purchase is required for warranty
service. If service is required and covered by warranty, the unit will be repaired or replaced with new or factory
rebuilt parts at no charge. The defective components must be returned to the address specied, with shipping
charges prepaid. Be sure to include your name, address, telephone number and a copy of the sales receipt
showing the date of original retail purchase. All sales receipts are subject to verication.
This warranty does not apply if the unit has been damaged by accident, abuse, misuse, poor installation or
misapplication, or if it has been modied from its original condition, or if any serial number has been removed
or defaced or altered. This warranty does not cover any expense to remove or reinstall the unit or any of its
components. If a returned unit is not covered by warranty, the sender will be notied and given an estimate
of the charges to repair or replace the unit, together with the return shipping charges.
THIS WARRANTY DOES NOT COVER SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM
ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO
DAMAGE TO OR REPLACEMENT OF OTHER EQUIPMENT AND PROPERTY. THE WARRANTY AND REMEDIES SET
FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. DUE
TO THE SPECIAL AND UNIQUE CONDITIONS THAT MAY EXIST IN EACH APPLICATION, THE MANUFACTURER
SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO DEALER, AGENT OR EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION,
EXTENSION OR ADDITION TO THIS WARRANTY.
Some states do not allow exclusion of incidental or consequential damages, so the above exclusions may not
apply to you. This warranty gives you specic legal rights, and you may also have other legal rights, which may
vary from state to state.
1.604.940.2010 | sales@cmpgroup.net
Inhaltsverzeichnis
Andere CMP TV-Halterung Handbücher
