CNC UC400ETH Bedienungsanleitung

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Breakoutboard für

UC400ETH

Operation Manual

All rights to these operating instructions remain with cnc-technics Texts, information and

illustrations of these operating instructions may not be reproduced, distributed or used for

purposes of competition without authorization or communicated to others

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Table of Contents

Introduction ................................................................................................................................ 3

Delivery Parts............................................................................................................................. 3

Description ................................................................................................................................. 4

Commissioning........................................................................................................................... 5

Inputs.......................................................................................................................................... 6

Outputs ....................................................................................................................................... 8

Adjust the Axes ........................................................................................................................ 10

Adjust the Spindle .................................................................................................................... 12

Spindle direction.................................................................................................................. 13

Relay outputs............................................................................................................................ 16

Status Display........................................................................................................................... 17

Charge Pump ............................................................................................................................ 18

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Introduction

This manual contains instructions for mounting, using the breakout board

It is imperative to connect 230V connections by a knowledgeable

electrician.

These operating instructions have been prepared with care If you still find

errors, we would be grateful for an indication

Delifery

•Current version of the manual

•Breakoutboard

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Description of the breakout board

The breakout board enables the operation of up to 4 stepper motor or servo

output stages on the UC400Eth

For this the control Software Mach3 / UCCNC (not included) is used The board

has various inputs and outputs that can be individually set as many different

configurations are possible Depending on the selected configuration,

additional functions are available, such as control of a frequency converter via

an analog signal of 0-10V or 0-5V, reference switch, spindle direction relay, up

to 3 relay outputs and one Charge Pump

All signals are protected by Optocouplers All machine-side signals are rated

from 5V to 30V, ensuring robustness and compatibility even with industrial

sensors (PNP SENSORS)

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Commissioning

Installation of the UC400ETH

The UC400ETH is screwed onto the 4 spacer bolts with M3 screws

The operating voltage is supplied via the Breakoutboard

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Inputs

Each input port is provided with its Pin number

in Mach3/UCCNC at Ports & Pins has to put a hook in Active Low

When the limit switch is actuated, it internally switches to ground and Mach3 detects a

response at the input PNP sensors switch with the switching voltage so they are also direct

connected

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Outputs

Like the input port, each output port is also provided with a pin number and an associated *

(output)

example

X32-1 is Number 6 = Port2/Pin6 and

X32-2 is Number 6* = Port2/Pin6

For 5V sensors, relays or similar loads you can put a bridge of 5V on the respective pin

number, so you can use a power supply

For switching max 50mA per output are available. If you need higher currents for switching

you can connect inexpensive relay modules.

You can connect to any pin without * a direct voltage, max to 30V

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Integrate Outputs in Mach3

The Port Number and the Pin Number are used, the hook at enabled to enable output

Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg

Tel: 081386695536 www cnc-technics de

Set Axes in Mach3/UCCNC

These are fixed values that should not be changed

Inhaltsverzeichnis

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung