Cobra CB 19 DX4 EU Bedienungsanleitung

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 2 / 13 2

SPECIFICATIONS

1. GENERAL

Channels………………………...……………………..............................EU CH AM/FM 1W/4W

Frequency Range………………………………...………………………..26.565 to 27.99125 MHz

Temperature Range……………………..…………………….………..…-10°C / +55°C

Input Voltage………………………………...…………………………......13.2VDC ±15%

Size………………………………………….……………..………190(L) X 45(H) X 120(D) mm

Weight……………………………………………………..………………....Approx. 0.945 kg

2. RECEIVER

Receiving System………………………………………………………...Super Heterodyne

Frequency…………………………………………….…1st IF: 10.695 MHz, 2nd IF: 455 MHZ

Sensitivity……………………………………….....….0.5 µV for 12 dB SINAD in FM mode Audio

Distortion……………………………………..………..……..……………Less Than 8% @ 1 KHz

Current Drain at standby…………………………………………………300 mA

3. TRANSMITTER

Output Power………………………………………………..……….MAX. 4W @ 13.2 V DC

Modulation………………………………………………...………….FM: 1.7 KHz / AM 65%

Frequency response………………………………………………...From 400 Hz to 2.5 KHz

Output impedance…………………………………..……………… RF 50 ohm

MIN Current Drain……………………………………………………1500 mA

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 3 / 13 3

OPERATION INSTRUCTIONS

Having properly installed your batteries and hooked-up the antenna, you are now ready to operate your

radio for optimum reception and voice transmission.

Turn the power “ON” with ON/OFF switch.

Set the desired channel in FM or AM.

Adjust the squelch control knob to reduce any undesirable background noise when no signal is being

received. To do this, select a channel where no signal are present, or wait until signals cease on your

channel. Then, rotate the squelch control knob clockwise to a point where the background noise

disappears.

Note: When the squelch is set properly, the speaker will remain quiet until a signal is received. In order to

receive weak signals, do not set the squelch too high.

Adjust the volume to the desired listening level.

To Transmit

Press and hold the push-to-talk button. Speak slowly and clearly in a normal voice two to three inches from

the microphone. A built-in modulation control circuit will automatically adjust the microphone input level.

There is no need to speak loudly.

To Receive

Release the push-to-talk button.

Note: Other operations mode see user manual.

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 4 / 13 4

THEORY OF OPERATIONS

TRANSMITTER

A. RF Amplification

The output of double AMP Q14 is fed through tuning IFT L8 to the base of pre driver AMP Q15. The

output is then supplied through tuning circuit L9 to RF driver AMP Q16. The output of Q16 is supplied

with tuning circuit L10 and C116,C67,C95 and goes to the base of final RF AMP Q17. The output of Q17

is supplied to the antenna through L-C tuning circuit.

B. Modulation Control

i. FM

The mic input is fed to mic audio amplifier IC which drives modulation varicap diode D403 in the VCO

circuit. RV1 is used to limit the incoming modulation audio levels to inhibit over modulation.

ii. AM

Modulation signals are filtered with RC network and goes to the audio power AMP IC IC103 to make

nominal signal level to achieve wanted modulation. To control incoming audio signal, diode D7 and

corresponding ALC circuit is used to limit the incoming modulation.

C. Receiver

CB receiver is dual conversion super-heterodyne type with the first IF 10.695 MHz and second IF 455 KHz.

Receiver is separated into two blocks, 1st IF section and 2nd IF section. The PLL synthesizer supplies first

local frequency 37.26 ~ 38.686 MHz.(for EU) With the provided first local frequencies to Q2,Q3 mixes the

incoming RF signal to generate first IF signal. Mixed signals were filtered with the XF1 (10.695 MHz)

crystal filter and other tuning circuits. The filtered signal is then further mixed with the second local

frequency of 10.24 MHz to generate the second IF. Output signal of mixer is filtered with CF1 (455 KHz

ceramic filter). The 455 KHz signal from the 2nd IF filter was amplified and limits internally. After

amplification the signals fed the quadrate detector loop L20. Then we can see the recovered audio signals

on Pin 9 for FM of IC7. With the amplitude of recovered signals, Q10 serves as an audio amplifier. For

AM signal, it will be passed through the filter CF1 and be induced to Q6, Q7 respective and detected to

voice signal by D5.

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 5 / 13 5

TROUBLESHOOTING HINTS

Symptom Possible Causes Remedy Suggestions

Unit does not work

at all

• Defective power switch

• Blown fuse

• Broken DC power cord

• Defective components

• Replace defective components

No output from

speaker at all

• Defective external speaker jack

• Poor connection on microphone connector

• Defective push switch on microphone

• Defective internal speaker

• Defective VR1 and IC8

• Replace defective components

No noise on

speaker

• Measure all the voltage of IC7 with voltage chart

• Defective squelch circuit components (RV5, VR2,

IC7) • Replace defective components

Squelch does not

work • Defective VR2, RV5, IC3-D. • Replace defective components.

• Re-adjust Squelch sensitivity

No modulation

• Defective microphone.

• Poor audio output and defective IC3.

• Defective microphone connector components.

• Defective ALC circuit D8, D9

• Replace defective components.

• Re-adjust Tx modulation

LCD meter does

not work

• Defective D11, D22

•DefectiveIC5.

• Defective RV2. RV6

• Replace defective components.

• Re-adjust RX meter display

LCD display does

not work •DefectiveREDwirefuse.

• Defective LCD module • Replace defective components.

Channel selector

does not work • Defective IC5. • Replace defective components.

EMG CH9.19 does

not work • Defective IC5. • Replace defective components.

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 6 / 13 6

TEST SETUP

A. TX test setup:

Spectrum Power

Analyzer Supply

Modulation Wattmeter Radio

Meter 10W U.U.T.

Oscilloscope Frequency AudioGen.

Counter

B. RX test setup:

SINADMeter RFSignal Power

Generator Supply

Distortion 8ohm Radio

Meter load U.U.T.

Oscilloscope

Note: U.U.T. = device under test

Filter with

attenuation

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 7 / 13 7

ALIGNMENT PROCEDURE

VCO Voltage

1. Test point TP1 connect to the multi-meter，set UUT enter test mode. Use channel “UP” key to select CH41

(26.565MHz) of DE Band in FM mode.

2. Adjust IFT L17 for 1.0 ±0.1V on the Multi-meter read，and then checking CH40 (27.99125MHz) of UK Band

should be less than 3.8V.

RX Alignment

Audio Level

1. UUT set to FM mode CH19，output of RF signal generator connect to TP2. Audio dummy load connect to

EXT. Speaker. (@8Ωload)

2. Set RF S.S.G Freq.: 10.695MHz，Mod.: ±1.2KHz，Fmod.: 1KHz, Output level:1mV.

3. Squelch Volume set to minimum position, volume control set to around middle position.

4. Adjust IFT L20 for maximum audio output amplitude.

Sensitivity

1. UUT set to FM mode CH22, output of RF signal generator connect to TP5 (Antenna).

2. Set RF S.S.G Freq.: 27.225MHz, Mod.: ±1.2KHz，Fmod.: 1KHz, Output level:0.5uV.

3. Adjust the volume control for 2V output on distortion meter read.

4. Adjust L2 & L3 for more than 12dB at SINAD meter.

T-Squelch Sensitivity

1. UUT set to AM CH22, output of RF signal generator to the antenna input terminal.

2. Set RF S.S.G Freq.: 27.225MHz，Mod.: 60%，Fmod.: 1KHz, Output level: -47dBm.

3. Volume control and Squelch control set to maximum position.

4. Adjust the RV5 to mute the speaker, then slowly turn RV5 to a position that the audio output on the speaker

just appears from no output. Turn the RF S.S.G. output level to -57dBm, the audio must be off from the

speaker.

RX Signal Meter Display

1. UUT set to AM CH22，output of RF signal generator to antenna input terminal. RF Gain volume at maximum.

Power switch turn on.

2. Turn the RF S.S.G output for 100uV without modulation.

3. Adjust RV6 for 9 characters displayed at the RX signal strength of the LCD.

4. Turn the RF S.S.G level output increase 30dB, the RX signal strength should up to +30 position.

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 8 / 13 8

TX Alignment

TX Output Power and Frequency

1. UUT set to FM EU CH19, Antenna connect to the RF power-meter input terminal.

2. Set UUT to TX mode, adjust the IFT L8 and L9 for TX power output maximum, and then adjust the RV4

check the output TX power for 3.5W.

3. Change to channel to EU CH19,Adjust the trimmer capacitor CT1 to 27.185000 +/- 500Hz on frequency

counter.

TX Modulation Deviation

1. UUT set to FM EU CH19, input of power-meter to antenna input terminal. Couple to MIC socket from the

audio frequency signal generator output terminal.

2. Set audio frequency signal generator @ FREQ.: 1000Hz, Output level: 50mVrms.

3. Set UUT to TX mode, adjust RV1 for 1.5KHz deviation on modulation meter.

4. Set UUT to AM mode; Set audio frequency signal generator @ FREQ.: 1000Hz, Output level: 50mVrms.

5. Set UUT to TX mode, adjust RV3 for 65% deviation on modulation meter.

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 9 / 13 9

VOLTAGE CHART

Transistor Pin TX RX Transistor Pin TX RX

Q2 E 0 0 Q32 E 0 0

C 0 0.8 C 0 6.0

B 0 6.7 B 3.5 0

Q2 E 0 0 Q37 G 0 0

C 0 0.8 S 0.5 7.9

B 0 6.7 D 2.8 0

Q14 E 1.2 0 Q40 G 0.7 0.9

C 8.0 0 S 0 0

B 2.0 0 D 0 6.1

Q16 E 0 0

C 8.5 3.0

B 1.0 0

Q17 E 0 0

C 13.2 2.0

B 13.0 0

Q18 E 0 7.3

C 0 0

B 0.5 7.9

Q19 E 8.1 8.10

C 7.9 0

B 7.3 7.9

Q28 E 6.1 6.1

C 8.1 8.1

B 6.8 6.8

Diode Pin TX RX Diode Pin TX RX

D1 A 0.5 7.1 DZ1 A 0.4 0.4

K 0 6.1 K 8.7 8.7

D2 A 0.5 7.1 D16 A 2.5 0

K 0 6.1 K 2.2 2.2

D5 A 0 0 D19 A 7.9 0

K 0 0 K 7.3 0

D6 A 10.6 2.8

K 9.7 2.8

D10 A 0 0

K 12.8 13.2

D14 A 7.9 0

K 7.2 0.6

Model No: 19 DX4 EU

Cobra Rev.:A

Page: 10 / 13 10

IC4

PIN TX RX PIN TX RX

1 4.2 4.2 9 3.6 3.6

2 4.7 4.7 10 4.0 4.0

3 1.0 1.7 11 4.5 4.5

4 0 0 12 0.7 0.7

5 5.0 5.0 13 0 0

6 0 0 14 0 0

7 0 0 15 4.7 4.7

8 0 0 16 4.1 4.1

IC3

PIN TX RX PIN TX RX

1 3.2 3.2 8 0 1.8

2 3.2 3.2 9 0 1.8

3 3.2 3.2 10 0 1.8

4 7.9 7.9 11 0 0

5 3.7 3.7 12 0 0

6 3.9 3.9 13 0 1.7

7 3.9 3.9 14 0 0

IC8

PIN TX RX PIN TX RX

1 1.0 1.0 4 6.3 6.3

2 0.8 0.8 5 13.2 13.2

3 0 0

IC6 PIN TX RX PIN TX RX

1 5 5 3 13.2 13.2

2 0 0 - - -

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cobra Radio Handbücher

Cobra

Cobra MR HH450 DUAL Bedienungsanleitung

Cobra

Cobra 19 DX IV Bedienungsanleitung

Cobra

Cobra 29 LTD Series Bedienungsanleitung

Cobra

Cobra 38 WX ST Betriebsanleitung

Cobra

Cobra 148GTL-DX Bedienungsanleitung

Cobra

Cobra 19DX IV Bedienungsanleitung

Cobra

Cobra 29 LX LE Bedienungsanleitung

Cobra

Cobra 19 DX IV Bedienungsanleitung

Cobra

Cobra 29 LX LE Referenzhandbuch

Cobra

Cobra 29 LTD Classic Contents Betriebsanleitung

Cobra

Cobra GR 29 LTD ST Bedienungsanleitung

Cobra

Cobra SoundTracker INTL75 Bedienungsanleitung

Cobra

Cobra 38 WX ST Bedienungsanleitung

Cobra

Cobra 19 MINI Bedienungsanleitung

Cobra

Cobra 19 Ultra III Bedienungsanleitung

Cobra

Cobra 29 LX CAMO Bedienungsanleitung

Cobra

Cobra 75 WX ST Bedienungsanleitung

Cobra

Cobra Harley-Davidson 29 LTD HD LE Bedienungsanleitung

Cobra

Cobra 29 LTD Classic Bedienungsanleitung

Cobra

Cobra 29 LX EU Bedienungsanleitung

Cobra

Cobra microTALK FRS 307-2 VP Bedienungsanleitung

Cobra

Cobra 29 WX NW BT Bedienungsanleitung

Cobra

Cobra 29NW ST Bedienungsanleitung

Cobra

Cobra Cobra 25 NW ST Bedienungsanleitung

Beliebte Radio Handbücher anderer Marken

EisSound

EisSound KBSound iSelect Bedienungsanleitung

Midland

Midland 1001LWX Bedienungsanleitung

Konig

Konig HAV-SR41 Bedienungsanleitung

Roberts

Roberts exprssion Bedienungsanleitung

VDigi

VDigi DD3.0 Bedienungsanleitung

Radio Shack

Radio Shack 21-1863 Bedienungsanleitung

Roberts

Roberts Stream 207 Bedienungsanleitung

Sony

Sony Walkman SRF-M97 Bedienungsanleitung

Stanley

Stanley FatMax FMC770 Bedienungsanleitung

auna

auna DAB-Radio 10026947 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR190 Bedienungsanleitung

HYT

HYT TC-320 Bedienungsanleitung

auna multimedia

auna multimedia Yellowstone 10026851 Bedienungsanleitung

B-Tech

B-Tech GMRS-V2 Bedienungsanleitung

Weierwei

Weierwei VEV-V8 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER DAB750 Bedienungsanleitung

Telefunken

Telefunken TF-1505 Bedienungsanleitung

Makita

Makita LXRM03 Bedienungsanleitung