Coelbo SWITCHMATIC 1 Einrichtungshandbuch

SWITCHMATIC 1 / 1 plus

SWITCHMATIC 2 / 2 plus

SWITCHMATIC 3 / 3 plus

ADVANCED SETTINGS

Risk of damaging the pressure assemblies and/or the plant.

Risk by electric shock.

Risk for people and/or objects.

GENERAL

Read carefully the instructions before installing this unit. Verify the tech-

nical characteristics of the motor in order to assure the compatibility with

the device.

DESCRIPTION (diagram A)

SWITCHMATIC 1 is an electronic pressure switch with integrated digital

manometer. It manages the start and stop of a single-phase pump up to

2.2kW (3 HP) (SW1-2). Cut-in and cut-out pressures are easily adjustable

through the users control panel.

Wiring is analogous to the traditional electromechanical switch.

It can operate as a dierential pressure switch and as reverse pressure

switch.

Unit SWITCHMATIC 2 in addition to all the features of the basic SWITCH-

MATIC includes instantaneous reading of current drawn. This patented

system controls and manages the overcurrent, dry-run operation and

fast-cycling.

Unit SWITCHMATIC 2 in addition to all the features of individual assembly

includes the option to be synchronized to another unit SWITCHMATIC 2

managing and protecting 2 pumps operating in cascade with alternated

starting sequence. The SWITCHMATIC 3 unit is ideal for a control panel as

it has a dry contact output.

CLASSIFICATION AND TYPE

According to IEC 60730-1 and EN 60730-1 this unit is a control sensor

device, electronic, independent assembly, programming type A with action

type 1B (microdisconnection). Operating value: I <20% I learned. Pollution

degree 2 (clean environment). Rated impulse voltage: cat II / 2500V. Tem-

peratures for ball test: enclousure (75) and PCB (125).

OPERATING CHARACTERISTICS (diagram C)

• Adjustable cut-in and cut-out pressures.

• Integrated digital pressure gauge with bar and psi indication.

• Inner pressure transmitter.

• Dry-run protection:

• Through minimum adjusted height for basic SWITCHMATIC 1/3.

• Through the instantaneous current consumption in case of SW2.

• Overcurrent protection.

• Overvoltage protection.

• ART Function (Automatic Reset Test). When the device has stopped

the pump by the intervention of the dry-running protection system,

the ART tries, with scheduled basis, to re-start the pump in order to

restore the water supply. See “ART. Automatic reset function“. Must be

activated in the step 6 of the ADVANCED MENU (Ar1).

• Fast cycling: when the hydropneumatic tank has lost too much air and,

consequently, frequent start-stop cycles are produced this alarm is

activated and is delayed the start of the pump. Activated (rc2).

• Manual start push-button (ENTER).

• 3 operation modes: dierential, reverse and synchronized.

• Control panel with 3-digit display, LED indicator lights and push-

buttons.

• Available settings:

• Stand-by mode.

• Minimum period between fast cycles.

• Start and stop delay.

• Volt-free contact for monitoring the alarms displayed in the screen (only

version A).

TECHNICAL CHARACTERISTICS

• Rated motor power: 0,37-2,2 kW (SW1-SW2)

• Power supply: ~1 x 110-230 V (SW1-SW2)

~1 x 48-230 Vac/Vdc (SW3)

• Electric outlet: Dry contact (SW3)

• Nominal pressure 1MPa/10bar (plus: 1,3MPa / 13bar)

Frequency: 50/60Hz

• Max. current: 16 A, cos  ≥ 0.6

• Protection degree: IP55

• Max water Temperature: 50ºC

• Max environment Temperature: 60ºC

• Cut-in range (start pressure) 0,5÷7 bar (version plus=11 bar)

• Cut-ot range (stop pressure) 1÷8 bar (version plus=12 bar)

• Max. dierential (Pstop-Pstart) 7,5 bar (version plus=11,5 bar)

• Minimum dierential (Pstop-Pstart)) SW: 0,5 ba

SW2 synchro: 1 bar

• Factory setting (start/stop) 3/4 bar

• Hydraulic inlet G1/4” Female - NPT 1/4” Fem.

• Net weight (without cables) 0,3 kg

HYDRAULIC INSTALLATION (diagram A)

SWITCHMATIC equipment must be threaded to a tting G1/4” male

at the pump´s outlet.

Before connecting the SWITCHMATIC verify that the hydraulic system is

properly installed, especially if the hydropneumatic tank is pressurized.

ELECTRIC CONNECTION (diagram B)

The electric connection must be performed by qualied personal in

compliance with regulation of each country. Before doing manipulations

inside the device, it must be disconnected from the electric supply.

Wrong connection could spoil the electronic circuit.

The manufacturer declines all responsability in damages caused by

wrong connections.

When carrying out the electrical connection it is compulsory to use a dieren-

tial switch of high sensitivity: I = 30 mA (clase A o AC). It is compulsory to use a

magnetothermic switch adapted at the motor load.

Check if power supply is between 115-230V (SW1-2).

If you have purchased the unit without cables follow diagram B:

• Use cables type H07RN-F 3G1 or 3G1,5 with section enough to the power

installed.

• Do the pump connection U, V and (SW1-2) o 1, 2 y al cuadro (Only

SW3)

• Do the power supply connection L1, N and .

• The earth conductor must be longer than the others. It will be the rst

one to be mounted during the assembly and the last one to be discon-

nected during the dismantling. The earth conductors connections are

compulsory!

• (Only version A) The device has a volt-free contact for monitoring the alarms

displayed in the screen originated by irregularities or problems of the system.

For the connection see Diagram C.

CONTROL PANEL (diagram C)

The meanings of the dierent control panel elements are summarized on the

following tables, where:

• O means lit LED light.

• ( ( O ) ) means slow-ashing.

• (((O))) means fast-ashing.

DISPLAY ACTION

OPERATION MODE Is showed on screen instantaneous pressure or instanta-

neous current consumption

ADJUSTMENT MODE

Is displayed on screen the adjusted start pressure

blinking.

Is displayed on screen the adjusted stop pressure blin-

king.

Is displayed the adjusted rated current blinking (only

SW2).

ALARM MODE Is displayed the alarm code

STAND-BY MODE Are displayed 3 ashing dots

BASIC CONFIGURA-

TION MODE Is displayed the sequence of basic conguration para-

meters

ADVANCED CONFI-

GURATION MODE Is displayed the sequence of advanced conguration

parameters

LEDS STATE MEANING

bar

OIt indicates the instantaneous pressure in bar

( ( O ) ) It indicates the instantaneous pressure in bar +

pump operating (only SW1/SW3)

psi

OIt indicates the instantaneous pressure in psi

( ( O ) ) It indicates the instantaneous pressure in psi +

pump operating (only SW1/SW3)

(only SW2)

OIt indicates the instantaneous current consumption

in Ampere units

( ( O ) ) Pump ON

START O Is displayed the start pressure

( ( O ) ) Adjusting start pressure

STOP O Is displayed the stop pressure

( ( O ) ) Adjusting stop pressure

ORatied dry-running or overload alarms

( ( O ) ) Dry-running alarm performing ART or overload

alarm preforming any of the 4 restore attempts

(((O))) Fast-cycling alarm

P-BUTTON TOUCH ACTION

click!

From state ON: unit OFF.

From state OFF: the pump starts and keeps opera-

ting until reaching Pstop.

From any conguration MENU: the parameter

value is accepted.

HOLD

DOWN

From state ON: unit OFF.

From state OFF: the pump starts and keeps opera-

ting until the push-button is released.

click! Pstart is displayed on the screen for 3 seconds.

3” Pstart adjustment mode.

click! Pstop is displayed on the screen for 3 seconds.

3” Pstop adjustment mode.

click!

Is displayed on the screen instantaneous current

consumption.

If it is already displayed then we switch to instanta-

neous pressure view.

3” Rated current adjustment.

STARTUP (diagram C)

Before starting the device please read the previous sections, espe-

cially “Hydraulic Installation” and “Electrical connection”.

Follow next steps:

1. Only for type SW2 set the pump rated current intensity value.

- Press during 3 seconds.

- The current intensity value is displayed on screen, LED A lights up and

display is ashing.

- By mean of and is adjusted the rated current reected in the

characteristics plate of the motor. See Note 1.

- Press for validation.

2. Start the device by pressing .

3. Set the cut-in (start) pressure:

- Press during 3 seconds.

- The start pressure value is displayed on screen, LED START lights up

and display is ashing.

- By mean of and is adjusted the start pressure from 0,5 to 7

bar (+ version=11 bar).

- Press for validation.

4. Set the cut-out (stop) pressure:

- Press during 3 seconds.

- The stop pressure value is displayed on screen, LED STOP lights up

and display is ashing.

- By mean of and is adjusted the stop pressure from 1 to 8 bar

(+ version=12 bar).

- Press for validation.

5. The unit is ready to operate but more optional adjustments can be set

through basic and advanced MENUS. See the next chapter.

Remark 1: it is important to introduce exactly the rated current

specied on the nameplate of the pump.

BASIC MENU + (diagram C)

- Press simultaneously + during 5 seconds.

- By mean of or the values can be changed.

- Press for validation.

- The parameters sequence is:

it TYPE SYSTEM REACTION FACTORY

SETTING

1 BAR P We can select the pressure units displayed

beetween bar and psi. bar

2rc0 rc2

Fast-cycling alarm:

- rc0: alarm unabled.

- rc1: activated, when hammering is detected

it is delayed the start in order to protect

the pump.

- rc2: alarm is activated and the pump is stop-

ped upon detection.

rc2

3 r.01 r.99

Only if fast-cycling alarm has been activated in

the previous step (rc1&rc2). It can be choosed

the maximum time period between 3 consecu-

tive starts that will be considered fast cycling

(between 1 sec. and 99 sec.)

3 se-

conds

4 Sb0 Sb1 Stand-by mode activated (Sb1), for low power

consumption, or unabled (Sb0). Sb0

ADVANCED MENU + +

- Press simultaneously + + during 5 seconds.

- By mean of or the values can be changed.

- Press for validation.

- The parameters sequence is:

it TYPE SYSTEM REACTION FACTORY

SETTING

1 nc no Select the operation MODE as a conventio-

nal pressure switch (nc = normally closed) or

reverse (no = normally open). *see remark 3 nc

2 E00 E01/02

(Only Switchmatic2). Select the operation

mode Individual (E00) or Master/Slave (E01/

E02) in case of be assembled in groups of

two pumps.

E00

2.1 d.05 d.1 (Only Switchmatic 2). Sets the minimum gap

between Pstart 1 and Pstart 2 and/or Pstop

1 and Pstop 2. d.05

3 ct0 ct9 Sets a time delay between 0 and 9 seconds

to the start (is not available in synchronized

operation mode). ct0

4 dt0 dt9 Sets a time delay between 0 and 9 seconds

to the stop. dt0

5 Ar0 Ar1 Activation of the automatic restore system

ART (Ar1) o disable (Ar0). Ar0

6 P0.0 Px.x

It allows setting a minimum operating

pressure under which the device would

determine dry-running operation. It is very

usefull in the basic model SWITCHMATIC

where there is no reading of current intensi-

ty drawn. See Note 2.

0 bar

0 psi

6.1 t05 t99

Set the time period between 5 and 99

seconds below the minimum operating

pressure that will be considered a dry-

running operation.

20”

7 c10 c30 It allows setting a % of nominal current

above which the device will activate the

overcurrent protection. c20

8 rS0 rS1 If we change rS0 to rS1 and push ENTER

default values are restored. rS0

Remark 2:

Basic SWITCHMATIC 1/3 can only detect dry-running

operation through the minimum pressure. This means that

plumber must determine the water column of the installa-

tion, the start pressure of the pump and place the minimum

pressure below the start pressure.

It can also occur that pumping system is running out of its

curve so that the pump is unable to provide the minimum

pressure because the ow requirement is excessive. In this

case SWITCHMATIC 1/3 would activate a false dry-running

alarm.

If these concepts are not clear, it is preferable not congure

this protection or install the SWITCHMATIC 2 with accurate

and easy setting of dry-run detection.

Remark 3:

By choosing “no” (normally open) it will operate as an auxi-

liary pressure control element in the suction of the pump. It

will restart when the suction pressure reaches the congu-

red PStart.

Example: - PStop: 0,9 bar

- PStart: 1,2 bar

SYNCHRONISATION (ONLY FOR SWITCHMATIC 2)

SWITCHMATIC 2 can be synchronized to another unit SWITCHMATIC 2

managing and protecting 2 pumps operating in cascade with alternated

starting sequence. Next steps must be followed:

1. GO TO ADVANCED MENU: + +

- In step 2: select E01 in a unit (this one will be the master) and select E02

in the other unit (this one will be the slave).

- In step 3: select identical parameters of gap between pressures d.XX.

This is the dierence beetween the starting pressure of main and au-

xiliary pumps, it is also the dierence beetween stop pressures of both

pumps.

2. Press repeatedly until exit the ADVANCED MENU.

3. SET identical cut-in and cut-out pressures in both units.

To optimize the synchronization, the minimum dierence between

the start and stop pressures must be at least 1 bar.

4. Press in order to disable the units. Is displayed “OFF”.

5. Press again in both units in order to activate the synchronization.

Remark 4: after 10 cycles the unit congured E01 will display pressu-

re and the unit congured E02 will display current in Amps.

PRESSURE SENSOR CALIBRATION

In case of wrong lecture of the pressure sensor it can be adjusted again.

For the pressure sensor calibration is necessary to have a pressure gauge

in the installation. Proceed following next steps:

ZERO REGULATION

1. Open the taps living the hydraulic net without pressure.

2. Press simultaneously the buttons and until the display show 0.0

ashing.

3. Press to validate.

FULL SCALE

1. Start the pump until cut-out of the pressure switch.

2. Press simultaneously the buttons and till the display ashes with

a gure.

3. Adjustthe pressurewith the arrowspush-buttons to getthe pressurede-

sired.

4. Press to validate.

Remark 5: pressure sensor decalibration should not be a normal

event. If it is frequently repeated contact the technical service.

WARNINGS AND ALARMS

COD. DESCRIPTION SYSTEM REACTION

A01

DRY-RUNNING

(Only for

SWITCHMATIC 2)

When is detected a dry-run operation the

pump is automatically stopped. By mean

of ENTER the normal operation can be

manually restored.

( ( O ) )

After the activation of the dry-running

alarm if the Automatic system reset (ART)

is enabled, a rst attempt at 5 minutes and

then an attempt every 30 minutes for 24

hours is performed in order to restore the

normal operation. This alarm can also be

reset manually with the ENTER push-but-

ton. If the alarm persists after 24 h we nd

a denitive alarm.

A11 O

DRY-RUNNING

(BY MINIMUM

PRESSURE)

Is displayed during normal operation if the

pressure is below the minimum pressure

(Px.x) - previously set - during a period

(txx) - also previously set - in the ADVAN-

CED MENU.

If at any time the pressure exceeds the mi-

nimum pressure, the operation is restored

automatically and the alarm is cleared.

Normal operation can also be restored

manually by pressing ENTER.

A02

OVERLOAD

(Only SW2)

Overcurrent alarm is activated when the

nominal pump current is exceeded.

4 automatic reset attempts prior to the

nal alarm are performed.

During the attempts display will show

current.

Normal operation can also be restored

manually by pressing ENTER.

( ( O ) )

A04 (((O))) FAST CYCLING

(Hammering)

This alarm can be unabled or activated in

the BASIC MENU. The alarm is activated

when 3 consecutive cycles occur in a range

lower than the set time (between cycle and

cycle).

If it has been activated rc1, this alarm does

not stop the normal operation but are

added 5 seconds to the start delay in order

to protect the electric pump.

If it has been activated rc2, the pump is

stopped.

To RESET the normal operation press

ENTER.

A05 O

DAMAGED PRES-

SURE TRANS-

MITTER

CONTACT WITH YOUR SUPPLIER.

EC STAMENT OF COMPLIANCE

COELBO CONTROL SYSTEM, S.L.

States, on our own responsibility, that all materials here with related com-

ply with the following European Directives:

- 2014/35/EU.

- 2014/30/EU.

- 2011/65/EU.

Name: - SWITCHMATIC 1 /1+

- SWITCHMATIC 2/2+

- SWITCHMATIC 3/3+

Standards : EN-60730-2-6, EN-60730-1, EN-61000-6-1, EN-61000-6-3, IEC-

60730-1, IEC-60730-2-6

F. Roldán Cazorla

Director Técnico

04/05/2016

COELBO CONTROL SYSTEM, S.L.

Ctr de Rubí, 288 - P.I. Can Guitard

08228 Terrassa - BARCELONA (SPAIN)

~1x48-230Vac/Vdc

DIAGRAM A INDIVIDUAL

GROUPAL (ONLY SW2)

SWITCHMATIC 1/2 SWITCHMATIC 3

Ausgang

alarms

DIAGRAM B

Press to release

CABLE:

max. 1.5mm²

mín. 0.2mm²

CONTACT RATING

Max. switching voltage:

- 230VAC / 220 VDC

Max. switching power:

- 62,5VA / 30W

(Alarm monitoring)

SWITCHMATIC 1/2

SWITCHMATIC 1/3

SWITCHMATIC 2A/3/3A

SWITCHMATIC 2

DIAGRAM C

DIMESIONS

V11_042019

Andere Handbücher für SWITCHMATIC 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Coelbo Relais Handbücher

Coelbo

Coelbo SWITCHMATIC 2T Einrichtungshandbuch

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung