Coemar ProSpot LX Bedienungsanleitung

1^ edizione, dicembre 2000

1st edition, december 2000

manuale

di istruzioni

instruction

manual

ProSpot LX

numero di serie/serial number

data di acquisto/date of purchase

fornitore/retailer

indirizzo/address

cap/città/suburb

provincia/capital city

stato/state

tel./fax/

Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro ProSpot

LX: in caso di richiesta di informazioni, pezzi di ricambio, servizi di riparazione o altro ci permetteran-

no di assistervi con la massima rapidità e precisione.

Please note in the space provided above the relative service information of the model and the retailer

from whom you purchased your ProSpot LX: This information will assist us in providing spare parts,

repairs or in answering any technical enquiries with the utmost speed and accuracy.

ATTENZIONE: la sicurezza dell’apparecchio è garantita solo con l’uso appropriato delle presenti

istruzioni, pertanto è necessario conservarle.

WARNING: the security of the fixture is granted only if these instructions are strictly followed; the-

refore it is absolutely necessary to keep this manual.

English
Index
Packaging
Transportation
Important safety information
Lamp: installation and replacement
Operating voltage and frequency
Mounting the unit
Mains connection
Signal connection
Powering up
DMX addressing
Display panel functions
1. Turning on the ProSpot LX without articulated movement
2. Resetting the electronic lamp life counter
3. test
DMX 512 channel functions
Aligning the lamp in the optical path
Automatic repositioning features
Gobo replacement
Altering the operating voltage and frequency
(Reserved for technical staff only)
1 Selecting the voltage on the autotransformer
2 Selecting the frequency on the power supply of the ProSpot LX
Maintenance
Electronic alignment of motors
Error messages
Spare parts

English

Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both

in componentry and in the technology used. We renew our invitation to you to complete the service information on the

previous page, to expedite any request for service information or spares (in case of problems encountered either during, or

subsequent to, installation). This information will assist in providing prompt and accurate advice from your coemar service

centre.

Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for

years to come.

Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the

equipment, contact your carrier immediately by telephone or fax, following this with formal notification in writing.

packing list

Ensure the packaging contains:

1 ProSpot LX

1 instruction manual

1 T 8A fuse

The ProSpot LX should be transported in its original packaging or in a coemar approved flight case.

We recommend the use of a suitable flight case, which will stop the articulated movement of the ProSpot LX during tran-

sportation.

2. Transportation

1. Packaging

English

Fire prevention:

1. ProSpot LX utilises a Philips MSD 250W/2. The use of any other lamp is not recommended and will null and void the

fixture’s warranty.

2. Never locate the fixture on any flammable surface.

3. The minimum distance from flammable materials: 0,5 m.

4. The minimum distance from the closest illuminable surface: 2 m.

5. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any

doubt.

6. Connect the projector to main power via a thermal magnetic circuit breaker.

Prevention of electric shock:

1. High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any func-

tion, which involves touching the internals of the unit, including lamp replacement.

2. For mains connection, adhere strictly to the guidelines outlined in section 7 of this manual.

3. The level of technology inherent in the ProSpot LX, requires the use of specialised personnel for all service applications;

refer all work to your authorised coemar service centre.

4. A good earth connection is essential for proper functioning of the projector.

Never operate the unit without proper earth connection.

5. The fixture should never be located in an exposed position, or in areas of extreme humidity. A steady supply of circulating

air is essential.

Protection against ultraviolet radiation:

1. Never turn on the lamp if any of the lenses, filters, or the housing is damaged, their respective functions will only operate

efficiently if they are in perfect working order.

2. Never look directly into the lamp when it is operating.

Safety:

1. The projector should always be installed with bolts, clamps, and other fixings, which are suitably rated to support the

weight of the unit.

2. Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the pri-

mary fixing point.

3. The external surfaces of the unit at various points may exceed 80°C. Never handle the unit until at least 10 minutes have

elapsed since the lamp was turned off.

4. Always replace the lamp if any physical damage is evident.

5. Never install the fixture in an enclosed area lacking sufficient airflow; the ambient temperature should not exceed 45°C.

6. A hot lamp may explode. Always wait for at least 10 minutes to elapse after the unit has been turned off prior to attemp-

ting to replace the lamp.

Always wear suitable hand protection when handling lamps.

3. Important safety information

English

ProSpot LX utilises a Philips MSD 250W/2 or equivalent.

The lamp is available from your authorised coemar sales agent:

coemar cod. 105214/1

power 250 w

luminous flux 18.000 lm

colour temperature 8.500° K

lamp base GY 9,5

approximate life 2000 hours

The fixture’s internal temperature can reach 150° C after 5 minutes with a maximum peak of 350° C; ensure that the lamp is

cold prior to attempting removal. The fixture should be allowed to stand and cool for 10 minutes prior to its removal.

The lamps are part of the mercury vapour family of discharge lamps and must be handled with great care. The lamps opera-

te at high pressure, and the slight risk of explosion exists if operated over their recommended lamp life.

We recommend, therefore, that the lamp be replaced within the manufacturer’s specified lamp life.

installing the lamp

1) Using a Philips head screwdriver, remove the 4 screws Alocated at the front and rear of the projector, which affix the top

cover B, as shown in the diagram below.

2) Remove the housing B.

3) Remove the three thumbscrews C, which hold the lamp-

cover in place, and remove the cover.

Attention

Disconnect mains prior to opening up the unit

4. Lamp: Installation and replacement

English

4) Locate the lampholder D

5) Insert the lamp. The lamp is manufactured from quartz glass and should be handled with care; always adhere to the instruc-

tions supplied in the lamp’s packaging. Never touch the glass directly; use the tissue provided in the lamp’s packaging. The GY

9,5 lampholder is asymmetrical in construction, with one lamp pin larger than the other is. DO NOT USE UNDUE FORCE. In

case of difficulty, inspect for physical damage and then repeat the installation procedure.

6) The optimal gap between the lamp and the parabolic

reflector is around 2 to 3 mm. If this is not the case, rota-

te the two adjusting thumbscrews located at the rear of

the projector as indicated in the section of this manual

entitled “Aligning the lamp in the optical path”.

The lamp must under no circumstances come into

contact with the reflector or other components of

the optical system.

7) Reposition the lamp cover and replace the three screws Cpreviously removed. Replace the housing Band refasten the

four screws Aas per the original condition of the ProSpot LX.

Prior to switching on the projector with the new lamp installed, reset the lamp life counter as described in section 11

“Display panel functions”.

We recommend that replacement lamps be realigned in the optical path of the lamp so as to avoid any accidental

overheating of the internal components of the fixture. This procedure is described in the section of this manual entitled

“Aligning the lamp in the optical path”.

English

The projector may operate at 100-115-208, 230 or 245V .at 50 or 60 Hz; coemar presets (barring specific requests), an

operating voltage of 230V and a frequency of 50Hz. The operating voltage and frequency of the projector is noted on the

base of the unit.

If this preset does not correspond with the conditions in your particular country of operation, follow the instructions in the

appropriate section of this manual.

Incorrect frequency and voltage selection will detrimentally affect the operation of the projector.

factory set

main at: 100V

115V

208V

230V

245V

50Hz

60Hz

5. Operating voltage and frequency

English

mounting

ProSpot LX can operate in any mounting position.

The structure from which the unit is hung should be of sufficient

rating to hold the weight of the unit, as should any clamps used to

hang the unit. The structure should also be sufficiently rigid so as to

not move or shake whilst the ProSpot LX moves during its opera-

tion.

The two mounting holes Ø13 mm (A) on the base of the ProSpot

LX allows the projector to have hook clamps fitted for the purpose

of hanging.

safety chains

The use of a safety chain fixed to the ProSpot LX and to the pri-

mary suspension structure is highly recommended to protect against

the accidental failure, however unlikely, of the primary suspension

point.

If using an aftermarket safety chain not manufactured by coemar,

ensure that it is of a sufficient rating to hold the weight of the unit.

The safety chain is attached by means of the two holes Blocated in

the base of the unit as shown in the diagram.

movement

The projector has an articulated movement of 530° in the base and 284° through its yoke; DO NOT obstruct the articula-

ted movement in any way.

protection against liquids

The projector contains electric and electronic components that must not come into contact with water, oil, or any liquid.

risk of fire

Each fixture produces heat and must be installed in a well-ventilated position. The minimum recommended distance from

flammable material is 0.5m. Minimum distance from the object being illuminated is 2m.

forced ventilation

You will note that the projector’s housing contains several air entry points and fan outlets, positioned both on the head and

the base of the unit; under no circumstances should any of these points be obstructed!

Obstruction of any of these points will result in the over-heating of the unit, detrimentally and seriously affecting the proper

operation of the ProSpot LX.

On this point, refer to section 18 “Electronic motor alignment”, subsection temperature (temp).

6. Installing the unit

English

cable preparation

The mains cable provided is thermally resistant, complying with the most recent international standards.

NB: In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusively (cable

3x1,5 ø external 8 mm, rated 300/500V, tested to 2KV, operating temperature -40° +180°).

mains connection

ProSpot LX can operate at voltages from 208V-230V-240V at 50 or 60Hz (operating voltage and frequency can be selec-

ted as described in section 5 and 16 of this manual). Prior to connecting the unit to your mains supply, ensure that the

model in your possession correctly matches the mains supply available to you.

For connection purposes, ensure your plug is of a suitable rating: 2,1 amps at 245, 230v, 208V and 4,7 at 100 and 115V.

Locate the mains cable, which exits the base of the unit and connect as shown below:

protection

The use of a thermal magnetic circuit breaker is recommended for each ProSpot LX.

A good earth connection is essential for the correct operation of the fixture. Strict adherence to regulatory norms is strongly

recommended.

ProSpot

massa/ground

neutro/neutral

fase/live

marrone - brown

blu - blue

giallo/verde - yellow/green alimentazione

main

7. Mains connection

Inhaltsverzeichnis

Andere Coemar Beleuchtungsausrüstung Handbücher

Coemar

Coemar i spot S Bedienungsanleitung

Coemar

Coemar LEDko EXT Bedienungsanleitung

Coemar

Coemar Reflection LEDko Bedienungsanleitung

Coemar

Coemar Stage Lite Led sc Bedienungsanleitung

Coemar

Coemar Risalto Led + Bedienungsanleitung

Coemar

Coemar Otello 6 HD + Bedienungsanleitung

Coemar

Coemar Reflection LEDko Bedienungsanleitung

Coemar

Coemar Par Lite Led Bedienungsanleitung

Coemar

Coemar Par Lite Led Bedienungsanleitung

Coemar

Coemar Panorama Power MK2 Bedienungsanleitung

Coemar

Coemar Par lite ACL Bedienungsanleitung

Coemar

Coemar ProWash 575 LX Bedienungsanleitung

Coemar

Coemar MiniLEDko Spot Bedienungsanleitung

Coemar

Coemar par lite LED IP Bedienungsanleitung

Coemar

Coemar Infinity Spot S Bedienungsanleitung

Coemar

Coemar CF 1200 Spot Bedienungsanleitung

Coemar

Coemar pilota 1200 Bedienungsanleitung

Coemar

Coemar Mini ReLite Led Bedienungsanleitung

Coemar

Coemar REFLECTION LEDko EXT Bedienungsanleitung

Coemar

Coemar LineaLed Stick Bedienungsanleitung

Coemar

Coemar LEDko EXT Bedienungsanleitung

Coemar

Coemar LEDko FullSpectrum 2 + RGBL Bedienungsanleitung

Coemar

Coemar Reflection LEDko T Studio Bedienungsanleitung

Coemar

Coemar CF 1200 Hard Edge Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung