ColorKey Mover MicroSpot Bedienungsanleitung

Mover MicroSpot

CKU01-5000 (US) / CKE01-5000 (EU)

USER MANUAL

Introduction

Thank you for purchasing the ColorKey Mover MicroSpot. Please read these instructions

carefully before use. O

perating this fixture according to these instructions is important to

avoid any possible damage or

accidents caused by misuse.

!Packing list

"1x Mover MicroSpot moving head fixture

"1x Power cord

"User Manual

Safety

Caution! Opening this unit voids warranty. Contact ColorKey for any service requests.

Warning! To avoid electrical shock, be sure to disconnect power before any service or when

moving or setting up the fixture.

Caution! Avoid direct eye exposure with the fixture when on.

!This fixture is for indoor use only.

!This fixture must be installed a minimum distance of 5 meters (16’4”) away from any

lighted objects.

!Do not install or operate this fixture near flammable materials.

!This device must be installed, operated, and maintained by a qualified professional.

!Do not touch the fixture with bare hands during operation as the surface temperature of

the fixture can exceed 60˚C (140˚F). Turn off power and wait 15 minutes for the fixture to

cool before attempting to touch it.

!Please check if the voltage is in accordance with the rated power before installing.

!Do not operate this fixture if the power cord has been damaged. Turn off fixture and

replace with a power cord of similar rating.

Display Operation

!MENU: Access the menu/Scroll through menu options

!ENTER: Open/Select the current menu option

!UP: Scroll through menu selection or parameter increase

!DOWN: Scroll through menu selection or parameters decrease

DMX Values

11 channel mode

9 channel mode

Value

Function

000-255

Pan

Pan (fine)

000-255

Tilt

Tilt (fine)

000-007

008-014

015-021

022-028

029-035

036-042

043-049

050-056

057-127

128-189

190-193

194-255

Color

Color 1

Color 2

Color 3

Color 4

Color 5

Color 6

Color 7

Color 8

Half color

Color wheel speed (fast-slow)

Stop

Color wheel speed (slow-fast)

000-007

008-015

016-023

024-031

032-039

040-047

048-055

056-063

064-071

072-079

080-087

088-095

096-103

104-111

112-119

120-127

128-189

190-193

194-255

Gobo

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Gobo 1 shake

Gobo 2 shake

Gobo 3 shake

Gobo 4 shake

Gobo 5 shake

Gobo 6 shake

Gobo 7 shake

Gobo 8 shake

Gobo wheel speed (fast-slow)

Stop

Gobo wheel speed (slow-fast)

000-255

Strobe

000-255

Dimmer

000-255

Pan/Tilt speed

000-069

070-079

080-089

090-099

100-109

110-119

120-199

200-209

210-249

250-255

Mode

Black out when Pan/Tilt rotating

Black out when Color wheel rotating

Black out when Gobo wheel rotating

Reset

Sound function

000-255

Dimming mode

Menu Guide

Main Menu

Sub Menu

Function

ADDR

0-512

DMX addressing

CHND

8CH/10CH

Channel section

SLMD

MAST

Mast mode

SL1

Slave mode 1

SL2

Slave mode 2

SHND

SH1

Sound operation 1

SH2

Sound operation 2

SH3

Sound operation 3

SH4

Sound operation 4

SOUN

ON (sound function)

OFF

OFF (sound function)

SENS

000-100

Sensor sensitivity (Sound function)

LED

ON (LED display)

OFF

OFF(LED display OFF with no operation to

LED panel in one minute)

DISP-INVERT

LED display (forward/backward)

PAN INVERT

YES

PAN forward rotation

PAN backward rotation

TILT INVERT

YES

Tilt forward rotation

Tilt backward rotation

TEST

Self-Test

Auto running in “self-test” function

VER

Software version

RESET

Reset

DMX Connections

!DMX Cable：

The Mover MicroSpot can be controlled via DMX using a 3-pin XLR connection. The

standard DMX connection is XLR is: one end connects to the male plug, and the other

connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal

Noted：In order to avoid failures and interference signal transmission，we connect a

resistance120Ω（1/4W ）at the end of the DMX connecting as below:

!The Conversion between 3 pin and 5 pin XLR

If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable

Master/Slave Mode Operation

Master/Slave

Master/Slave mode allows you to connect multiple units together using one (1) unit to control

others in a chain. When a fixture is set to ‘Master Mode,’ this unit will always act as a

controlling unit until it is switched out of ‘Master Mode’. The Master unit will send out signal

via DMX to Slave units which will react in synchronization. When a fixture is set into ‘Slave

Mode’, this fixture will receive the Master signal. To avoid master signal and DMX signal

interference, do not connect DMX when using Master/Slave mode. If using a DMX run

longer than 60 meters and/or over 32 units, a signal amplifier may be required.

Troubleshooting

Problem

Solutions

No DMX control

#Make sure that the DMX cable is properly connected

#Make sure that the DMX controller is operational

#Check the DMX cable for tears or breaks

#Make sure that the fixture is in DMX mode

Fixture does not

respond to sound

#Make sure that the fixture is in Sound Active mode.

Technical Information

Power supply: AC 110~240V，50/60Hz

Power consumption: 27W

Light Source：1x10W white LED

Life span: 60,000 hours

Beam angle: 13°

Channel: 9/11 DMX channel

Color: 7 colors plus open (white)

Gobo: 7 gobos plus open

Electronic adjustable strobe with high speed

Pan: 540°

Tilt: 270°

Control: Sound activate, master/slave, Automatic, DMX

Standard DMX512 control protocol

Working Environment：up to 40℃; Over heating protection

IP rate：IP20

Notice to consumer: ColorKey offers a 1-year limited warranty. Please visit our website at

www.ColorKeyLED.com to register your product.

Please note: As we continue to work towards improving our products and your experience

as a user, we recommend that you check our website periodically for updates to user

manuals and specifications at www.ColorKeyLED.com or you may contact us directly at

[email protected].

Inhaltsverzeichnis

Andere ColorKey DJ- und Lichttechnik Handbücher

ColorKey

ColorKey CKU01-2140 Bedienungsanleitung

Beliebte DJ- und Lichttechnik Handbücher anderer Marken

Cameo

Cameo CLSERUM Bedienungsanleitung

Beamz

Beamz Atlas LED Double Derby DMX 6x3W Bedienungsanleitung

Future light

Future light MCF-200 Bedienungsanleitung

BoomToneDJ

BoomToneDJ Hyper Dream LED Bedienungsanleitung

Varytec

Varytec LED Par 64 Floor 5in1 15x10W RGBWA Bedienungsanleitung

EuroLite

EuroLite TG-5 Bedienungsanleitung

Techni-Lux

Techni-Lux BL-400S Bedienungsanleitung

Chauvet

Chauvet S-PAR 1 Bedienungsanleitung

Future light

Future light PLB-130 Pro-Head-Beam Bedienungsanleitung

EuroLite

EuroLite SMD 48 Bedienungsanleitung

Ledj

Ledj Slimline 229 IR Bedienungsanleitung

Techni-Lux

Techni-Lux DL-QUADBOX1630TC Bedienungsanleitung

Future light

Future light PRO Slim PAR-12 QCL RGBW/RGBA Bedienungsanleitung

BoomToneDJ

BoomToneDJ mushroom led Bedienungsanleitung

EuroLite

EuroLite LED TMH FE-1000 Bedienungsanleitung

Allen + Roth

Allen + Roth 19535-000 Bedienungsanleitung

Robin

Robin Actor 3 ST Bedienungsanleitung

ACME

ACME LED-777 Bedienungsanleitung