Comcast XHS1-UE Bedienungsanleitung

XHS1-UE

ZigBee Home Automation 1.2

Wireless Digital Pet Resistant PIR Detector

XFINITY HOME

Installation Instructions

1. INTRODUCTION

The XHS1-UE pet resistant detector is a

microprocessor-controlled wireless digital PIR

detector supported by ZigBee Home Automation

1.2. The detector’s features are as follows:

A. Red LED

B. Green LED

C. Tamper Switch

Figure 1 – XHS1-UE

2. SPECIFICATIONS

Detector Type: Two - Dual element low-noise pyroelectric sensor

Optical Data: 18 parabolic mirrors for long range

18 parabolic mirrors for close range

Max. Coverage: 15 x 15 m, (49.2 x 49.2 ft) / 90°

Pet Immunity: Up to 38 kg (85 lb)

ELECTRICAL

Internal Batteries: Two 3V Lithium batteries, type CR-123A. For UL installations, use Panasonic only

Nominal Battery Capacity: 1400 mAh per battery

Battery Life (with LED on): Typically over 5 years

Note: Inability to connect with wireless network, or wireless link quality resulting in intermittent connection may

signiﬁcantly reduce the expected battery life.

Battery Power Test: Performed immediately upon battery insertion and during each transmission to the panel

FUNCTIONAL

Alarm Period: 3 seconds

Visual Indications: Red LED lights for about 3 seconds upon transmission of alarm & tamper messages and upon motion

detection in the walk test mode only (walk test mode available for approx. 15 minutes). Red LED ﬂashes during

the power-up stabilization period, or after restoring (pressing) the tamper switch (power-up stabilization period

is approx. 1 minutes). LED does not light upon transmissions of supervision messages or alarm detection after

termination of walk test mode.

Rearm Timer: Rearms the detector 2 minutes after the last alarm. Timer disabled in the walk test mode.

WIRELESS

Supported Network: ZigBee H.A 1.2

Frequency: 2.405 – 2.480 Ghz as per IEEE 802.15.4

Tamper Alert: Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored

MOUNTING

Height: 1.8-2.4 m (6 - 8 ft). For pet rejection, the optimal height is 2.1 m (7 ft)

Installation Options: Surface or corner

ENVIRONMENTAL

Operating Temperatures -10˚ C to 55˚ C (14˚ F to 131˚ F)

Storage Temperatures -20˚ C to 65˚ C (-4˚ F to 149˚ F)

COMPLIANCE WITH STANDARDS

USA CFR 47 part 15,

ANSI/UL 639

PHYSICAL

Size (H x W x D) 83 x 61 x 42 mm (3.27 x 2.4 x 1.66”)

Weight (with battery) 90 g (3.17 oz)

Color White

4. TROUBLESHOOTING

If you encounter one of the following problems with the XHS1-UE, use the following solutions to

resolve the problem:

Problem Solution

Attempt to pair the sensor is unsuccessful. Reset the detector to default mode and then set to

pairing mode (see section 3.5).

The sensor and the Touchscreen (control panel) Perform the signal strength testing procedure

do not communicate. described in the control panel installation manual.

Make sure that the signal is sufﬁcient. If necessary,

replace the sensor’s battery.

The sensor sends a Low Battery indication. To ensure continuous proper operation, replace the

battery within two weeks of the ﬁrst Low Battery

indication.

Panel does not arm because of an unrecognized Consult with your installer or system provider before

sensor malfunction. you disable a zone. Disable the sensor zone (see

the control panel user manual). Note that disabling

a sensor zone lowers the overall security level of

your system.

5. SPECIAL COMMENTS

Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure

/ improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity

in ambient temperatures close to that of the human body and unexpected failure of a component part. The

above list includes the most common reasons for failure to detect intrusion, but is by no means comprehensive.

It is therefore recommended that the detector and the entire alarm system be checked weekly, to ensure

proper performance. An alarm system should not be regarded as a substitute for insurance. Home and property

owners or renters should be prudent enough to continue insuring their lives and property, even though they are

protected by an alarm system.

6. COMPLIANCE WITH STANDARDS

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

You are cautioned that changes or modiﬁcations not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

ETL Statement: This device conforms to ANSI/UL STD 639

Installation shall be done in accordance with the Standard for Installation

and Classiﬁcation of Burglar and Holdup Alarm Systems, UL 681.

4008840

4 MUG-XHS1-UE-B Date: 11/01/2016 MUG-XHS1-UE-B Date: 11/01/2016 1

XHS1-UE_ UM_B.indd 1 11/4/16 12:37 PM

3. INSTALLATION

3.1 General Guidance

1. Do not install near heating and cooling sources.

2. Do not aim detector at windows due to risk of drafts.

3. Do not install outdoors.

4. Do not install where direct sunlight can strike the unit.

5. Do not install near high-voltage electrical lines.

6. Do not install behind any obstructions.

7. Do not mount on unstable surfaces.

3.2 Installation Procedure

1. Push in the direction of the arrow shown in

Figure 3 to separate detector from bracket.

2. Remove bracket.

3. Mount the bracket on the wall (see Figure 4).

4. Install new batteries.

If batteries are already installed, pull the

activation strip.

5. Mount the detector on the bracket by sliding

it downward until a click is heard (see

Figure 5).

6. The unit is ready for walk test.

Figure 2. General Guidelines

Figure 3 – Opening the Unit

Figure 5 – Replacing Batteries

Figure 4 – Mounting Detector on Bracket

Figure 7 - Coverage Pattern Walk-Test

3.3 Replacing the Batteries

1. Press upward to separate the detector from

the bracket.

2. Replace the batteries.

3. Put back the detector on the bracket.

Note: It is recommended to wait about 1 minute after battery removal, before inserting the new battery.

Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according

to the manufacturer’s instructions

3.4 Activating and Pairing the Detector

To pair the detector to the Touchscreen (control panel), you must set the detector to pairing mode.

1. First set the Touchscreen (panel) to pairing mode and then the detector.

2. To activate, pull the activation strip that protrudes from the back of the detector.

3. The green LED (see Figure 1) blinks 3 times every 5 seconds (repeated up to 20 times) to indicate

that the detector is searching for the Touchscreen (control panel).

Note: If detector pairing is not successful during the searching process – by pressing the tamper

switch – the searching process will restart.

4. Complete the pairing procedure on the Touchscreen (control panel). See the pairing instructions in

the Touchscreen (control panel) installation guide for details..

Note: Pairing should be performed before installation.

After the installation a good link to the panel is displayed when the Received Signal Strength

Indicator (RSSI) indicated on the panel is higher than -70dBm and the Link Quality Indicator (LQI) is

stronger than 250.

If the RSSI and LQI values are lower, you must change the location of the

detector.

3.5 Rebooting the Detector

To reboot the detector, complete the following steps:

1. Remove the battery cover.

2. Press and release the tamper switch for 1 to 2 seconds (see Figure 1)

3. Close the battery cover.

3.6 Return the Detector to default mode

CAUTION! The defaulting process removes the device from the network and enables re-pairing.

Prerequisite: Separate the detector from the bracket to remove both batteries.

See Figure 6 for details .

1. Press and hold down the detector’s tamper switch.

2. Insert one of the two batteries into the detector while observing battery polarity.

3. Release the tamper switch within 4 seconds (the LED blinks 3 times every 5 seconds).

4. To re-pair the detector, follow the instructions in section 3.4.

Note: It is recommended to wait about 1 minute after battery removal, before inserting the new

battery.

3.7 Walk Testing

Walk across the far end of coverage pattern in both directions. The LED should light for 2-3 seconds

each time your motion is detected.

Important! Instruct the user to walk test at least once a week to verify proper function of the

detector.

Note: After battery insertion or closing the cover (which results in closing the tamper switch) the LED

ﬂashes for 2 minutes and the detector goes into walk-test mode for 15 minutes. In walk test mode

the LED lights for every motion detected. After 15 minutes the detector automatically enters normal

mode in which the LED will not blink after detection.

2 MUG-XHS1-UE-B Date: 11/01/2016 MUG-XHS1-UE-B Date: 11/01/2016 3

XHS1-UE_ UM_B.indd 2 11/4/16 12:37 PM

Andere Comcast Sicherheitssensor Handbücher

Comcast

Comcast LDHD2AZW Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung