Comcater FC54-E Bedienungsanleitung
18
MANUALE DI ISTRUZIONE
PER LAVASTOVIGLIE
INSTRUCTION MANUAL FOR
DISHWASHERS
NOTICE D’UTILISATION
POUR
LAVE-VAISSELLE
GEBRAUCHSANWEISUNG
FÜR GESCHIRRSPÜLER
18
FOREWORD
1. Read the instructions contained in the enclosed booklet carefully, because it
contains important information on installation, operation and maintenance
safety. Store this booklet carefully for any further consultation by other
operators.
2. Having removed the packing material, check that all the equipment is
present. If there is any doubt, do not use it and contact qualified personnel.
The packing elements (plastic bags, foam polystyrene, nails, etc.) should be
kept away from children, because they are dangerous.
3. Before switching the equipment on, make sure that the model plate data
conforms to that of the electrical and water distribution network.
4. Installation should be carried out by qualified personnel according to the
manufacturer's instructions.
5. This equipment should be destined to the use which it has been conceived
for. Any other application should be considered improper and
consequently dangerous.
6. The equipment should only be used by personnel trained for its use.
7. Operators must strictly follow all hygienic requirements in the handling of
clean dishware and cutlery.
8. Do not leave the machine in an environment at temperatures lower than 0°C.
9. The protection of the machine is IP X4C, therefore it should not be washed
with high pressure directed water jets.
10.Qualified personnel only can access the control panel, after having
disconnected the machine from the primary current supply.
11.The appliance is made according to EEC 89/336 regarding radio noise
suppression and electromagnetic compatibility.
12.According to EEC directive nr.23 of 19/02/1973 and the law of actuation
nr.791 of 18/10/1987, our appliances are built-up according to the good
technique norms in force in Italy and abroad.
13.Noise level of the machine, less than 62dB(A)
19
INSTRUCTIONS FOR USE
INSTRUCTIONS FOR THE USER
20
OPERATION AND USE
1)Before washing make sure that:
•the wall-mounted on/off switch is switched on;
•the water tap is open;
•water is present in the distribution network;
•the pump protection filters are installed in their respective positions;
•the overflow in inserted;
•all rotating parts are free;
•the rinse aid dispenser is full;
•water temperatures maintain their regulated values:wash 55/60°C, rinse 85°C
(lamp "H1-H2" on).
•make sure that dishware is in good conditions as it may cause cleaning
difficulty and haven bacteria.
2)SWITCHING ON
Press the "Q1" button to enable the automatic wash tank filling and the
consequent triggering of the heating element. The lamp “H1-H2” flashes.
3)As soon as lamp "H1-H2" is on, pour about 30 gr. of detergent directly
into the tank, paying attention to distribute it uniformly on the filters, anyway
the quantity being according to supplier's instructions. Add 15 gr. every 7
cycles to achieve a concentration of 1,5 gr./lt. In order to respect our
environment, use only the correct amount of detergent. When using
chlorinated detergent, it is suggested to use an automatic dispenser, otherwise,
brownish spots might appear on the surfaces due to chlorine reactions.
Detergent injection should always be placed in the back of the machine (to see
page 30).
4)Introduce the dishware to wash, after having removed the solid waste and
having placed them into the proper racks. The cups and the glasses should be
turned upside down, while the cutlery should be put vertically into the proper
container, and the same applies to dishware.
INSTRUCTIONS FOR THE USER
21
5)START
With closed door, select the wash cycle according to conditions of the
dishware:
•with normally dirty dishes press "S3" button (rapid flashing of the lamp
"H3") (short cycle started);
•with particularly dirty dishes or deep dishes, press "S3" button for 3 sec.
(slow flashing of the lamp “H3”) (long cycle started).
The end of which will be indicated by the switching off of the "H3" lamp.
N.B.: Machine in conformity with the existing hygienic standards,
guaranteeing a final rinse at 85°C. Wash cycle automatically
lengthened if final rinse temperature is not reached.When this auto-
cycle intervenes and the cycle is pro-longed, flashes the “H3” indicator
to indicate this intervention. In any case after 8 minutes max. the
intervention is stopped and the cycle continues.
6)Remove the rack and slightly incline it to permit a perfect drain; allow
dishware to dry and after having washed one’s hands, handle the rack in order
not to touch the dishware inside then place the rack on hygienically clean
shelves.
7)DRAIN
When the wash operation has been completed open the front door and drain
the tank pulling out the overflow pipe.
For machines with drain pump open the front door, pull out the overflow pipe
and press the "S5" button for the drain cycle.
The machine will carry out the drain cycle (lamp "H5" on) for 2 minutes and
20 seconds.
To interrupt the drain cycle press "S5" button.
INSTRUCTIONS FOR THE USER
22
8)SELF-CLEANING AND DRAIN
When the wash operation has been completed (machine off) pull out the
overflow pipe, close the front door and press the "S5" button for the self-
cleanig and drain cycle.
The machine will carry out the cycle (lamp "H5" flashes) for 2 minutes and
20 seconds.
The end of which will be indicated by the switching off of the "H5" lamp.
At this point, the tank filter can be taken out, in order to be washed, then
replace it with the overflow in its place.
For further use , switch on the machine.
For any further information concerning equipment cleaning, read chapter
"USEFUL SUGGESTIONS".
9)When the washing is finished, switch off the equipment by turning off the
main supply through the general wall switch and close the water supply.
INSTRUCTIONS DURING THE WASHING
1)Do not plunge bare hands into the water containing the detergent. If this
happens, wash them immediately and abundantly with fresh water.
2)When the machine is operating, do not open the door too rapidly.
3)Use only specific anti-foaming detergents.
4)Disconnect the equipment in case the machine is out of order or it does
not work properly. For the repairs consult a technical assistance centre
authorised by the manufacturer and ask only for an original spare parts.
5)Never modify the thermostat settings.
6)Check that lamp "H1-H2" is on.
7)Wash tank water should be changed at least twice a day or according to
daily wash requirements.
8)Do not subject clean dishware to any further cleansing treatment such as
brushes or drying towels.If these instructions are not followed, the safety of
the equipment can be compromised.
INSTRUCTIONS FOR THE USER
24
USEFUL SUGGESTIONS
1) MAINTENANCE
IMPORTANT: Before carrying out the cleaning and maintenance operations,
disconnect the equipment from the electric supply.
Frequently check and clean the nozzles. The frequency of this operation will
depend on the quantity of residues, which may result in an unsatisfactory
washing result.
For the inside and outside cleaning of the machine, do not use corrosive
products such as sodium hypochlorite (bleach) savelling water and
hydrochloric acid, acids, steel wool or steel brushes.
The presence of calcium and magnesium salt in the water can compromise
machine performance, thus ask qualified personnel to remove the deposits
periodically.
In order to avoid some oxidation risks, or chemical reactions, generally the
stainless steel surfaces have to be well cleaned.
2) OPTIMAL RESULTS:
A possible wash deficiency can be noticed when residue remains.
Marks can be caused by an insufficient rinse: in this case check
that the rinse nozzles are clean and that there is sufficient water supply
pressure.
In case of dishware residue check that:
•the washing nozzles are clean
•the water temperature is around 60°C
•there is detergent
•the pump suction filter is clean
•the racks are suitable for the dishes and cutlery that are to be washed
•the position of the cutlery and the dishes in the racks are correct
INSTRUCTIONS FOR THE USER
25
3) TEMPORARY MACHINE NON-USE
In case the machine is stopped for some weeks, it is recommended before
closing it to fill the tank and run the machine with clean water, then empty it
out, in order to avoid the forming of bad odour and that any residue remains
in the pump.
If necessary repeat this operation until the water leaving the machine is clean.
If the machine is stopped for many weeks, it is recommended to oil the
stainless steel surfaces with paraffin oil and to discharge the water from the
boiler and the electric pump.
4)SANITIZING THE MACHINE
Sanitizing the machine at least once a week is of the utmost importance in
order to guarantee hygiene even when the machine is not in use.
It is advisable to use a disinfecting product suggested by an authorised
detergent dealer.
The use of this product will satisfy hygienic requirements, even during
machine non use.
Before switching off the machine run the machine briefly with clean
water.
5)HARD WATER CONDITIONS
If a hard water supply is present, mineral deposits will form within the machine
and also on dishware.
In order to avoid the above conditions a periodic removal of these deposits is
necessary.
The frequency and method of this operation upon consultation by your
detergent supplier.
INSTRUCTIONS FOR THE USER
25
6) RESINS REGENERATION OF THE WATER SOFTENER
(only for machines with built-in water softener)
The regeneration of the water softener resins is completely automatic. The
flashing of the regeneration lamp “H4” indicates the need to regenerate the
resins, in any case the presence of some opaque spots on the glasses will
show that it is necessary to start the regeneration.
This operation has to be carried out with full tank.
First of all, make sure that in the designated tank container “S” there is some
regeneration salt (1kg is enough for about 5 regenerations).
Close the front door and press the button “S4” for approx. 3sec.
After that the lamp “H4” remains switched on for 20 minutes (during this
operation the machine cannot be used).
The end of which will be indicated by the switching off of the "H4" lamp.
Ø(For further use , first switch off the machine).
At this point switch off the machine, to empty the tank (to see page 21) and
the equipment is ready to be used.
INSTRUCTIONS FOR THE USER
27
CONTROL PANELS
Q1 Main switch
S3 Push button “CYCLE SELECTION / START CYCLE”
S4 Push button “REGENERATION” (mod. FC54-EA)
S5 Push button “SELF-CLEANING / DRAIN CYCLE” (machine OFF)
Push button “DRAIN CYCLE” (machine ON / door frontal opened)
H1-H2 Pilot lamp “MACHINE ON" (flashing)
H1-H2 Pilot lamp “MACHINE READY" (fixed)
H3 Pilot lamp “MACHINE WORKING"
H4 Pilot lamp “REGENERATION” (mod. FC54-EA)
H5 Pilot lamp “SELF-CLEANING / DRAIN CYCLE
SSalt container (mod. FC54-EA)
IRegulating screw for rinse aid injector
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Comcater Spülmaschine Handbücher
