Comelit VEDOGSM Bedienungsanleitung
Passion.Technology.Design.
EN
TECHNICAL
MANUAL
Communication expansion module Art. VEDOGSM
(protocol number greater than 004)
• This Comelit product was designed for use in the
creation of security and home automation systems
in residential, commercial or industrial settings and in
public buildings or buildings used by the public.
• All activities connected to the installation of Comelit
products must be carried out by qualified technical
personnel, with careful observation of the indications
provided in the manuals / instruction sheets supplied
with those products.
• Cut off the power supply before carrying out any
maintenance procedures.
• Use wires with a cross-section suited to the distances
involved, observing the instructions provided in the
system manual.
• We advise against running the system wires through
the same duct as the power cables (230V or higher).
• To ensure Comelit products are used safely: carefully
observe the indications provided in the manuals /
instruction sheets and make sure the system created
using Comelit products has not been tampered with
/ damaged.
• Comelit products do not require maintenance aside
from routine cleaning, which should be carried out
in accordance with the indications provided in the
manuals / instruction sheets. Any repair work must be
carried out: for the products themselves, exclusively
by Comelit Group S.p.A., for systems, by qualified
technical personnel.
• Comelit Group S.p.A. does not assume any
responsibility for: any usage other than the intended
use; non-observance of the indications and warnings
contained in this manual / instruction sheet. Comelit
Group S.p.A. nonetheless reserves the right to change
the information provided in this manual / instruction
sheet at any time and without prior notice.
WARNING
• The manufacturer, Comelit Group S.p.A.,
hereby declares that the radio equipment type
Art. VEDOGSM conforms to directive 2014/53/
EU. The full EU conformity declaration is
available at the following web address: http://
pro.comelitgroup.com/files_cms/14-manuali/
file/Declaration_VEDOGSM_EN.pdf
• Art. VEDOGSM complies with standards
EN50131-1, EN50136-1, EN50136-2,
• All the system components must have safety
grade 2 or higher to obtain grade 2 alarm
system certification according to standard
EN50131.
CERTIFICATIONS
• All articles have an ID label for product traceability.
Two examples are shown below:
PRODUCT LABELS
interpretation serial number: 000PWWYYXXXXXXXX
serial
number
article
code
protocol number
date of manufacture
week of manufacture (WW) and year of
manufacture (YY) (in the sample label
1515= week15 of the year 15)
000P1515XXXXXXXX
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
VEDOGSM
VEDOGSM
000P1515XXXXXXXX
Via Don Arrigoni, 5
24020 Rovetta (BG) - Italy
EAN article
identification
code
manufacturer’s
name
serial
number
article
code
2
The GSM communication expansion module Art.
VEDOGSM allows telephone calls, SMS, MMS
and emails to be sent on the data network, plus
the sending of digital protocols and date and time
synchronisation. Combined with the voice mes-
sage card Art. VEDOVOICE, it allows the remote
management of the control panel by a voice com-
municator.
GSM MODULE FUNCTIONS
• GSM850, EGSM900, DCS1800, PCS 1900
• GSM/GPRS channel support
• Main or reserve telephone dialler
• Indication of alarms / malfunctions /
sabotage / events via SMS
• Customisable SMS messages
• Control panel status interrogation via SMS
• Checking residual credit of the prepaid SIM
• Transmission of Voice Messages via GSM
• Transmission of Contact ID via GSM
• Event transmission in Contact-ID and SIA
(Level 1) format via GSM and over TCP-IP
(SIA-DC-09 protocol support)
• Event transmission by email with images
• Event transmission by MMS
• Date and time updating
1. Antenna connector
2. SIM housing
3. Cavalier activation/désactivation led
4. Position du connecteur du module
Holes for fixing the VEDOGSM module to the control
panel card Art. PCBVEDO10, Art. PCBVEDO34, Art.
PCBVEDO68, Art. PCBVEDO200
TECHNICAL SPECIFICATIONS
Consumption (min./max.)
10mA in Idle
60mA in communication
Average power
consumption in 1 h:
VEDOGSM: 20mAh 1
alarm every 5 mins. and
communication with
duration of 1 minute.
Operating temperature
and Operating humidity
-10° / + 55° with warm
dry air
-10° / + 40° C with max + 93%
RH (not condensed)
Certified safety grade 2 according to EN50131-1*
Environmental class II according to EN50131-1
Features Value
Name of manufacturer /
supplier Comelit Group S.p.A.
Dimensions (b x h x d) 72 x 48 x 29 mm
(without antenna)
Weight 23g without antenna
41g with antenna
* Respecting any indications for configuration and installation
SPECIFICATIONS ACCORDING TO
STANDARD EN50136-2
CN1
CN2
RSVDDBG
LED DL1 DL2 DL3
DL4
1 2 43
Features Value
Types of alarm
transmission for which
the device is suitable
SP4 according to EN50131-1
Interface type Control panel expansion
Operating mode
saving and forwarding
event / event
transmission (pass-
through)
event transmission (pass-
through)
Generation and/or
transmission times of
alarm messages
voice messages: 10 sec
e-mail: 10 sec without image /
90 sec with image
MMS: 45 sec
Times for generating a
reply signal
(when used)
CONTACT ID: times according
to standard SIA DC-05-1999.09
SIA: times according to standard
SIA-DC-03-1990.01
SIA-DC-09: times according to
standard ANSI/SIA-DC-09-2007
Times for detecting
and presenting faults
No GSM/GPRS coverage:
120 sec.
SIM fault: 20 sec.
antenna disconnected: 45 sec.
Method for signalling
faults to alarm system
Alert send failure: regular or on
event
Level of output signals
and/or sensitivity of
input signals
Minimum level DTMF tones
at input: 36mVe - 28.8dbV
100mVpp
Level DTMF tones at output:
low freq 9dBm / high freq 11dBm
Safety signals level
supplied
Digital protocols protected for
info and replacement
Telephone protocols (Contact
ID and SIA): no information
protection
IP protocols: information
protection and protection from
replacement
Sharing of
transmission
connections
GSM: GSM850, EGSM900,
DCS1800, PCS 1900
Class 4 (2W) for GSM850 /
EGSM900
Class 1 (1W) for DCS1800 /
PCS1900
Voltage operating
range 10 - 15 V
3
MEANING OF THE LEDS ON THE IP GSM MODULE
Name Function
DL1
Green LED: module serial communication. Lights
up briefly when the module communicates with
the control panel.
DL2
Green LED: module serial communication. Lights
up briefly when the module communicates with
the control panel.
DL3 Red LED o: The module is not in operation.
Red LED rapid flashing (64ms On/ 800ms O):
The module is not connected to the network.
Red LED slow flashing (64ms On/ 2000ms O):
The module is connected to the network.
DL4
Red LED: GSM communication. Flashes when
a transfer via the GSM or GPRS network is
in progress, e.g. during receipt of an SMS or
during registration with the network at the time of
initialisation.
CONFIGURATION JUMPERS
Name Function
LED If disconnected, the LEDs go o
DBG Reserved
RSDV Reserved
FITTING THE GSM MODULE
Insert the plastic spacers in the relevant holes. Then,
taking care to plug the module connector into the
control panel connector designated MOD5 correctly,
apply sufficient pressure to engage the spacers in
the GSM expansion card and plug the connector in
almost completely.
Make sure the card on which you intend
to fit the module is not connected to the
power supply.
IMPORTANT: any operation involving the
assembly or disassembly of expansion
modules must be performed with all
input power (from power supply unit or
battery) OFF, in order to avoid permanently
damaging the expansion module you
intend to add or remove, as well as the
control panel card.
Once the module has been fitted correctly,
connect the antenna that you intend to use by
tightening the connector on the cable to the gold-
coloured connector on the GSM module.
Before using the module, it must be
enabled with the Safe Manager software. If
the module is enabled but not connected,
a fault will be generated.
The antenna must be correctly connected
and its connector must be fully tightened.
Antenna presence can be detected only
using the antenna supplied.
In all other cases antenna presence
detection must be excluded from the GSM
dialler options.
ANTENNA POSITIONING WITH
HOUSING ART. BOXMETAL
OK !
IIMPORTANT: place the antenna
outside the housing using the
"antenna outlet" provided
Do not place the antenna on metal
surfaces
NO !
5ª edizione 11/2018
cod. 2G40002353
[CHECK FOR UPDATES]
www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
CERTIFIED MANAGEMENT SYSTEMS
ANTENNA POSITIONING WITH HOUSING
ART. BOXPLASTIC
IMPORTANT: place the antenna in the
special slot under the battery (as shown in
the figure).
CAUTION:
If the position of the control panel does not
allow the reception of an adequate GSM
signal to ensure a good connection, it is
possible to fit an external antenna:
- moving the antenna and using an extension
cable,
- using an external antenna (Art. 2G50000296).
For this purpose, there is a pre-marked
section to allow easy exit of the antenna
cable.
Place the antenna at least 20 cm
away from the GSM module.
Do not place the antenna on metal
surfaces
20 cm
1
2
FITTING THE SIM CARD
√ The SIM card must be enabled for data trac, and
if it is a pay-as-you-go type, it must have sucient
credit on it to be able to make telephone calls, send
messages, transmit digital protocols via TCP-IP.
√ I
t is not essential to unlock it, because the control
panel is capable of managing the PIN to unlock
the SIM card.
1. Gently force the top of the SIM connector towards
the centre of the control panel card (downwards if
the control panel is already mounted on the wall).
2. Once you have overcome the resistance, turn it
over on its hinges.
3. Insert the SIM card in the mobile part in such a way
that you can see the gold-coloured contacts of the
SIM and that the bevelled corner is on the left.
4. Repeat the sequence in reverse to release the SIM
card from its seat.
First check that all power is OFF.
2
1
Andere Comelit Steuereinheit Handbücher
Comelit
Comelit 1622 Betriebsanleitung
Comelit
Comelit EXTRA 4+N MODULE Bedienungsanleitung
Comelit
Comelit 20004605 Bedienungsanleitung
Comelit
Comelit VEDOGSM4G Bedienungsanleitung
Comelit
Comelit 41ECN000 Bedienungsanleitung
Comelit
Comelit 3335 Bedienungsanleitung
Comelit
Comelit K1406 Bedienungsanleitung
Comelit
Comelit 1406 Bedienungsanleitung
Comelit
Comelit FT/GEN/05 Bedienungsanleitung
Comelit
Comelit SimpleHome 20046707 Bedienungsanleitung
Comelit
Comelit SK9000U Bedienungsanleitung
Comelit
Comelit Ultra Simplebus2 Bedienungsanleitung
Comelit
Comelit UT2010 Bedienungsanleitung
Comelit
Comelit UT9304M Bedienungsanleitung
Comelit
Comelit UT9331 Bedienungsanleitung
Comelit
Comelit 1621VC Bedienungsanleitung
Comelit
Comelit Ultra Simplebus2 Bedienungsanleitung
Comelit
Comelit Simplebus2 Ultra UT2020 Bedienungsanleitung
Comelit
Comelit 4680C Bedienungsanleitung
Comelit
Comelit SK9001U Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
