Comelit VEDO5TPR Bedienungsanleitung

USER

MANUAL

VEDO5TPR user manual

Introduction.....................................................................................................................................4

RFID sensing area.........................................................................................................................4

Screen: Code entry.......................................................................................................................4

Indications.......................................................................................................................................5

Buzzer...........................................................................................................................................5

Key to indicator LEDs.....................................................................................................................5

Main screen.....................................................................................................................................6

System status..................................................................................................................................6

Alarm or tampering alert screen...................................................................................................7

Quick commands from the home scen........................................................................................7

Arming.............................................................................................................................................7

Disarming........................................................................................................................................7

Arming with zones open................................................................................................................8

Arming with zones excluded.........................................................................................................8

Arming with zones isolated...........................................................................................................9

Arming while faults are present....................................................................................................9

Arming while tampering is present...............................................................................................9

Using the RIFD key.........................................................................................................................9

System options.............................................................................................................................10

Zonestatus.....................................................................................................................................11

Users..............................................................................................................................................11

Event log........................................................................................................................................12

Telephone contacts list................................................................................................................12

Areastatus......................................................................................................................................12

Output commds.............................................................................................................................13

Quick commds..............................................................................................................................14

Quick command selection buttons on the main screen...........................................................14

App launch.....................................................................................................................................15

Alarm options................................................................................................................................16

Enable installer..............................................................................................................................16

Register key..................................................................................................................................16

Delete key......................................................................................................................................17

Timer..............................................................................................................................................18

Auto arming...................................................................................................................................18

Configuration................................................................................................................................18

Configuration menu....................................................................................................................18

Device ID.....................................................................................................................................19

Device Password........................................................................................................................19

User code..................................................................................................................................19

BUS485 speed............................................................................................................................20

Backlighting level........................................................................................................................20

Screen lock.................................................................................................................................20

Reset configuration.....................................................................................................................21

Information..................................................................................................................................21

Manufacturing test......................................................................................................................21

Emulated keypad........................................................................................................................21

Table of contents

Introduction

VEDO5TPR is a keypad with 5” touchscreen that is compatible with all sizes of Vedo control panels.

Thanks to its many functions, it can be used to arm and disarm the system, check the status of the system and

its areas and zones, and to view the users associated with the control panel and its telephone contacts list.

The event log section can also be used to view the event and alarm logs.

RFID sensing area

(for alarm arming/disarming using an

authentication key and user ID)

Screen: code entry

To carry out procedures, you must log in with a user code and/or an RFID key. When the code is required, the

following screen will appear:

Enter the code (6 digits) and then press to confirm, to cancel.

OR:

hold the key next to the scanning zone to enter the code and perform authentication.

IMPORTANT: en combinación con un nuevo panel de control aún en fase de programación, solo el usuario 1

está activo con el código "111111".

IMPORTANT: if the screen is not touched for one minute, it will switch off and enter energy saving mode.

Alerts

Buzzer

The buzzer integrated into the VEDO5TPR beeps when any valid key is pressed. Furthermore, depending on

the options selected during the programming stage, the buzzer can signal:

Beep* Alerts

• Key pressed

— (1 sec.) Arming conﬁrmed

— (2 sec.) Total disarming conﬁrmed

•••••••• (2 sec.) Failed arming

•••••••••••••••••••• At least one zone is in alarm condition

•••••••••••••••••••• At least one zone is in "pre-alarm" condition (time period between zone viola-

tion and Alarm event generation).

• • • • • • • • • • • • Automatic arming pre-alert time

• • • • • • • • • • • • At least one zone is in "Exit time" condition

• • • • • • • • • • At least one zone is in "Entry time" condition

•·•·•·•·•·•·•·•·•·•·•·•·•· Signals that a zone with the chime attribute (zone opening alert chime) has

been opened. The buzzer is activated only if the violated zone is not armed

• • • • • • • • • • • • • Waiting for key to be presented for acquisition of RFID key

*The symbol "•” represents a short beep, the symbol “—” represents a long beep. The distance between the

“•” symbols represents the time frequency of the beeps. The size of the symbols represents the relative volume

of the beeps “•·”

Key to indicator LEDs

VEDO5TPR has a series of three LEDs in different colours on the front panel, which function as follows:

Colour Signal

Green ON System armed

Flashing green System not ready

Green OFF System ready

Yellow ON Problem detected

Flashing yellow Presence of isolated, excluded or inhibited zones, or of temporarily excluded

anomalies/sabotages

Yellow OFF No fault detected

Red ON System in alarm

Flashing red Alarm log

Red OFF No alarm detected

Main screen

To access the main screen, simply touch the screen if it is off, or use the relevant icons if you are already

accessing the menus.

The main screen appears as shown in the figure,

where the areas present in the control panel are

indicated. You can click on the description of

each area, or tap the centre of the circle to arm or

disarm the system (after entering the user code).

The key to colours (shown in the table below)

indicates the status of each zone.

You can also use the arrow pointing right to

navigate to the second page listing the quick

commands.

IMPORTANT: the screen will switch off after 30 seconds of inactivity (1 minute for the password entry screen)

and energy saving mode will be activated.

System status

The “System status” icon changes colour depending on the status of the system.

System armed

System part armed

System ready for arming

System NOT ready for arming (zones open...)

System NOT ready for arming (system faults...) Flashing padlock icon

System armed and in alarm condition

System in alarm condition due to tamper sabotage or panic alarm when unarmed

Alarm memory (system armed). Flashing padlock icon

Alarm memory (system unarmed). Flashing padlock icon

Moreover, in the event of faults and/or anomalies on the screen, the cause will also be shown. The image

below is an example of a device fault:

Alarm or tampering alert screen

In the event of alarms or sabotage, when the system is armed, a screen with a red background will appear

indicating the event. In this example, with the system armed, a “Burglary” type alarm is occurring.

The information will then remain available for reference within the “Event log” in the menu.

Quick commands from the home screen

The quick commands screen is easy to reach by pressing the arrow in the bottom right-hand corner of the

home screen.

The list of possible scenarios is shown on the left. On the right, the following quick commands appear by

default (*):

-Stop alarm

-Reset alarm

-Enable installer

*Refer to the “Quick Commands” section for further information regarding the customisation of icons available

on the home screen

Arming

If the system is unarmed, a full arming of all areas can be carried out by tapping the centre of the circle on the

main screen.

Conversely, if a specific area needs to be armed, you can click on its description or the corresponding part of

the circle.

If activated, the system can still be armed by means of a specific scenario.

Disarming

If the system is armed, a full disarming of all areas can be carried out by tapping the centre of the circle on the

main screen.

Conversely, if a specific area needs to be disarmed, you can click on its description or the corresponding part

of the circle.

If activated, the system can still be disarmed by means of a specific scenario.

Arming with zones open

If a zone is open during arming, and is not delayed and not available for exclusion, after the system analysis

screen, the following screen will appear:

If you press “Forcing” the system will be armed but the presence of an inhibited zone will be indicated by

the LED flashing (inhibited status will remain until the next system disarming). Press “Cancel” to cancel the

operation.

On the other hand, if the open zone has previously been set as not available for exclusion (action performed

using Safe Manager software), the following screen will appear:

Arming with zones excluded

If a zone is excluded during arming (and set as not available for exclusion), after the system analysis screen,

the following screen will appear, indicating how the system can be armed:

Arming with zones isolated

If a zone is isolated during arming, after the system analysis screen has been shown the following screen will

appear. It can be used to activate the zone, cancel the procedure, or continue to maintain isolation status

(forcing), as shown below:

Arming while faults are present

If a fault is present during arming, after the system analysis screen has been shown the following screen will

appear, indicating the fault and the option of forcing it (inhibiting it) to arm the system.

On the other hand, you do not possess the necessary authorisation for system arming (forced arming level 2),

the following screen will appear.

IMPORTANT: for information regarding these authorisations please contact your installer.

Arming while tampering is present

If a tampering event is present during arming, the system will behave in the same way as when a fault is

present (alarm alert or tampering present screen on page 6). If you attempt to confirm the arming without

permission, the “Act. locked” screen will appear.

Using the RFID key

With the RFID key you can:

Carry out a full system Arming / Disarming procedure by passing the key near the RFID sensor or additional

actions such as reset alarms, access the settings menu...

Full arming/disarming using the key is not possible during the device update procedure, the key

programming procedure or within the password entry screens.

»Scanning the key will be followed by the “System analysis” screen, then an “Arming executed” or

“Disarming executed” screen depending on the system status.

»If faults, open zones or tampering events are present during arming, the procedures described in the

paragraphs above will apply.

»If the key is not memorised in the system, the following screen will appear:

System options

The system options can be accessed from the homepage screen by clicking the icon in the top left corner.

Once the user code has been entered, the menu with its various options will be shown:

The system options menu includes the following entries:

• Zone status

• Users

• Event log

• Telephone contacts list

• Area status

• Output commands

• Quick commands

• App launch

• Alarm options

• Emulated keypad

The icon allowing access to the VEDO5TPR user manual through the scanning of a QR code is also

present.

Andere Handbücher für VEDO5TPR

Inhaltsverzeichnis

Andere Comelit Touch-Screen Handbücher

Comelit

Comelit 6501 Bedienungsanleitung

Beliebte Touch-Screen Handbücher anderer Marken

Elecro Engineering

Elecro Engineering Poolsmart Plus Montageanleitung

Johnson Controls

Johnson Controls IQ4 HUB Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET2270L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET1002L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems 3201L Bedienungsanleitung

Duratec

Duratec S15 Bedienungsanleitung

Crestron

Crestron TPMC-3SM Bedienungsanleitung

Racelogic

Racelogic MFD Touch Bedienungsanleitung

J2 580 Benutzerhandbuch

HAI

HAI OmniTouch 10p Bedienungsanleitung

panel

panel PC PSR108-FM Series Bedienungsanleitung

Tipro

Tipro FREE+ Bedienungsanleitung

Systemline

Systemline Commander Bedienungsanleitung

Interactive Technologies

Interactive Technologies Insite Bedienungsanleitung

GVision

GVision Legacy Bedienungsanleitung

BeiJer

BeiJer T21C-C24 Bedienungsanleitung

Advantech

Advantech ITM-5117 Series Bedienungsanleitung

Edge

Edge CS Bedienungsanleitung