Comfort Glow GA3450T Bedienungsanleitung

WARNING

Fanaccessorymustbegrounded.Fancomes

withathree-prong,groundingplugasshown

inFigure1.Theplugisyourprotectionagainst

electrical shock. Plug it into a standard,

three-hole, grounded, outlet. If cord needs

replacing,useonlyacordwithathree-prong,

grounding plug.

Instructions For Installing GA3450T

Thermostat Blower Accessory

Grounding Plug

Figure 1 - Grounding Plug

Grounded Outlet

Removing Upper Louver Assembly

To install the blower accessory, you must first remove the upper louver assembly.

Figure 2 - Removing Upper Louver Assembly

Continued

Cordlengthfromswitchplateassemblytoplug

is six feet. Make sure grounded outlet is an

appropriate distance from unit.

NOTICE

GA3450T for use on CGCF26T Series Compact Fireplace

Upper Louver

Assembly

Blower Bracket

Mounting Holes

CGCF26T Series

1. Lift screen off heater.

2. Remove 2 screws from louver assembly (see Figure 2). Save these screws.

3. Pull louver assembly straight out from the cabinet. Be careful not to scratch the paint. Set louver assembly and

screws aside.

WARNING

Failuretoconnectall wiresasindicatedmay

cause electrical shock or personal injury.

If any of these pieces are missing or damaged, contact the

dealer where you purchased this kit or DESA Interna-

tional at 1-800-972-7879 for referral information.

Hardware kit contains

2 Plastic snap bushings

6 #10 screws

1 Plug button

Carton Contents

Description Part Number

Bracket 103966-01

Thermodisc 103972-01

Blower 103283-01

Wire Harness 103968-01

Power Cord 104015-01

AUTO/OFF/ON switch 099998-01

Mounting Hardware kit 098418-08

104079

Wire

Harness

Bottom Louver

Assembly

Remove

Screw Valve

Cover

Shield

Shoulder

Screw

Installing Blower Assembly

Note:

If you are using a mantel with your heater, use the following instructions. If your heater is built-in, see For

Built-In Installation on page 3.

Standard Installation

Removing Valve Cover Shield

1. Open bottom louver assembly by swinging

the assembly down (see Figure 3).

2. Using short Phillips screwdriver, remove the

screw under the center of the branch support.

Rotatevalvecovershieldclockwiseandslide

out.

IMPORTANT :

Do not remove shoulder

screw on the left side of valve cover shield.

Slide the valve cover shield off of the shoul-

der screw (see Figure 3).

Note:

If you do not have a short Phillips

screwdriver, the screen, twigs, and branch

support must be removed so a longer

screwdriver may be used. Follow directions

in the owner’s manual for screen and twig

removal/installation. Branch support may

be removed by removing 2 screws on each

side of the support.

Figure 3 - Removing Valve Cover Shield

Figure 4 - Installing Blower Bracket Assembly

1. Install snap bushings found in hardware kit

into both holes in rear of valve cover shield.

2. Make sure the wire harness is firmly

connected to the terminals on the blower

bracket assembly.

3. Note the wire locations on back of AUTO/

OFF/ON switch. The terminals on back of

switch are numbered 1, 2, and 3. Carefully

remove red wire from terminal 1 and blue

wire from terminal 3. Black wire can

remain on middle terminal 2 (see figure 4).

4. Carefully disconnect green and white wires

at their insulated connectors.

5. In top of the heater cabinet, locate the four

mounting holes on the outer casing. Align

these four holes with those on the blower

bracket assembly. Attach blower bracket

assembly to the outer casing with 4 #10

screws provided (see Figure 4).

6. Route the wire harness through the hole in

left side of baffle. Pull wire harness through

lower opening above where the valve shield

was removed. (see Figure 4).

7. Insert the 4 wire harness into one of the

round holes in the rear of the valve cover

shield and through the rectangular hole in

the front of shield (see figure 4).

8. Reconnect red wire to switch position 3.

Reconnect blue wire to switch position 1.

Reconnect green and white wires.

Blower Bracket

Assembly

Screw

Power

Cord

Valve

Cover

Shield Box Cover

Wire

Harness

Switch

Plate

Switch

Baffle

Branch Support

Wiring Routing

Hole in Baffle

Snap

Bushings

Blue Red

104079

WARNING

A licensed electrician must connect the wiring harness to electrical supply following all local

codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be

routed through the bushing in the hole on the outer casing of heater.

Figure 5 - Installing Switch Plate to Valve Cover Shield

Follow instructions Removing Valve Cover

Shield (page 2), then

1. Install a snap bushing found in hard-

ware kit into one of the holes found rear

of valve cover shield. The other hole is

for a strain relief clamp (not supplied)

to secure incoming electrical supply.

Follow steps 2 through 6 in Installing

Blower Assembly, page 2. Also remove

black wire from middle switch terminal 2.

3. Remove black plastic strain relief and

power cord from switch plate. The

power cord supplied will not be used in

built-in installations. Pop in the plastic

snap bushing found in hardware kit into

the hole left by supply cord/strain relief.

4. A licensed electrician must follow the

wiring diagram on page 4 to connect

incoming electrical supply to fan kit

wiring harness.

5. Reinstall valve cover shield.

6. Test to make sure the blower is working

properly.

7. Reinstall upper louver assembly (see

Figure 1, page 1) and close lower

louver.

For Built-In Installation

Figure 6 - Installing Blower Bracket Assembly

Continued

Blower Bracket

Assembly

Screw

Wire

Harness

Power

Cord

Valve

Cover

Shield Box Cover Wire

Harness

Switch

Plate

Switch

Clamp Connector

(not included)

Valve Cover Shield

Switch Plate

Screw

Outlet

Receptacle

9. Install the switch plate on the valve

cover shield with 2 #10 screws provided

(see Figure 5, page 3). Reinstall the

valve cover shield. Route power cord out

of the cabinet by inserting it through the

bushing on the outer casing (see Figure

4). Plug fan kit into 120-Volt grounded

power supply and test operation.

Note:

When switch is in the AUTO position,

the fan will start after the heater has run

for a few moments. The fan will con-

tinue to run for several moments after

the heater has been turned off. When

switch is in the ON position, the fan will

run until turned to OFF. Reinstall upper

louver assembly (see Figure 1, page 1)

and close lower louver door.

Blue Red

OFF

Extension Cord

Use extension cord if needed. The cord must have a

three-prong, grounding plug and a three-hole receptacle.

Make sure cord is in good shape. It must be heavy

enough to carry the current needed. An undersized cord

will cause a drop in line voltage. This will result in loss

of power and overheating. Use a No. 16 AWG cord for

lengths less than 50 feet.

104079-01

REV. B

8/97

Red

Fan Switch

(Auto/Off/On)

Blue

Thermostat

Switch

(N.O.)

Green

White Green

White

110/115

V.A.C.

Blower

Motor

Black

Off

Auto

Figure 7 - Wiring Diagram For Fan Accessory Standard Installation

Operating Fan

This blower has three settings: ON, OFF, and AUTO.

In the ON position, the blower will operate con-

stantly. In the OFF position, the blower will not

operate. In the AUTO position, the blower will start

when the thermostat senses a sufficient increase in

firebox temperature.

Note:

Your fireplace and thermostat blower will not

turn on and off at the same time. The fireplace may

run for several minutes before the blower turns on.

After the heater modulates to the pilot position, the

blower will continue to run. The blower will shut off

after the firebox temperature decreases.

Note:

It is safe to operate fireplace with blower

turned off. However, the blower helps distribute

heated air from the fireplace.

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

Technical Service Department 1-800-323-5190

Parts Department 1-800-972-7879

Figure 8 - Auto/Off/On Switch

Auto/Off/On Switch

Andere Comfort Glow Kaminzubehör Handbücher

Comfort Glow

Comfort Glow CVSR18 Kurzanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung