Comfort Glow Brentwood LCF18 Bedienungsanleitung

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

VENTED DECORATIVE NATURAL GAS LOGS

OWNER’S OPERATION AND INSTALLATION MANUAL

RGA 2-72

APPROVED

TESTED AND

LISTED BY

BRENTWOOD

MODELS LCF18 AND LCF24

www.desatech.com 115043-01D2

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualied installer, service

agency or the gas supplier.

WARNING: This appliance is for installation only in

a solid-fuel burning masonry or UL127 factory-built

replace, constructed of noncombustible material and

connected to a working ue. (See page 6 for minimum

ue opening.

WARNING: This is a decorative gas appliance. It uses

air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must

be provided. Refer to the National Fuel Gas Codes, ANSI

Z233.1/NFPA 54, Section 5.3, Air for Combustion and

Ventilation.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made

by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identication........................................... 4

Local Codes......................................................... 4

Unpacking............................................................ 5

Optional Product Features................................... 5

Installation ........................................................... 5

Operating Appliance .......................................... 10

Cleaning and Maintenance................................ 12

Service Hints ..................................................... 12

Technical Service............................................... 12

Replacement Parts............................................ 12

Troubleshooting................................................. 13

Illustrated Parts Breakdown and Parts List........ 16

Accessories ....................................................... 18

Warranty Information ............................Back Page

www.desatech.com

115043-01D 3

WARNING: This appliance

is equipped for natural gas. An

optional propane/LP conversion

kit must be installed for use with

propane/LP gas.

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns.

WARNING: Installed decora-

tive glass door enclosures must

be fully opened when operating

this gas appliance.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the appliance.

Appliance assembly becomes

very hot when in use. Keep chil-

dren and adults away from hot

surface to avoid burns or clothing

ignition. Appliance will remain hot

for a time after shutdown. Allow

surface to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with appliance.

You must operate this appliance

with a replace screen in place.

Make sure replace screen is

closed before running appliance.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

SAFETy INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

WARNING: Keep ue open

when operating unit.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, operate

or service this log set. Improper use

of this log set can cause serious

injury or death from burns, re,

explosion, electrical shock and

carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the u, with

headaches, dizziness or nausea. If you have these

signs, the log set may not be working properly. Get

fresh air at once! Have log set serviced. Some

people are more affected by carbon monoxide than

others. These include pregnant women, people with

heart or lung disease or anemia, those under the

inuence of alcohol and those at high altitudes.

Natural Gas: Natural gas is odorless. An odor-

making agent is added to the gas. The odor helps

you detect a gas leak. However, the odor added to

the gas can fade. Gas may be present even though

no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this log set.

WARNING: Any change to

this log set or its controls can

be dangerous.

WARNING: Do not use a blow-

er insert, heat exchanger insert or

other accessory not approved for

use with this appliance.

www.desatech.com 115043-01D4

1. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• if you cannot reach your gas supplier, call

the re department

2. Never install the log set

• in a recreational vehicle

• where curtains, furniture, clothing, or other

ammable objects are less than 42 inches

from the front, top, or sides of the log set

• in high trafc areas

• in windy or drafty areas

3. Before installing in a solid fuel burning replace,

the chimney ue and rebox must be cleaned of

soot, creosote, ashes and loose paint by a qualied

chimney cleaner. Creosote will ignite if highly

heated. Inspect chimney ue for damage. If dam-

aged, repair ue before operating appliance.

4. This log set is designed to be smokeless. If

logs ever appear to smoke, turn off appliance

and call a qualied service person. Note:

During initial operation, slight smoking could

occur due to log curing and the burning of

manufacturing residues. You may wish to add

more ventilation by opening a window.

5. To reduce the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 12.

6. The installation and provisions for combustion

and ventilation air must conform with the Na-

tional Fuel Gas Code, ANSI Z233.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation.

7. Do not run log set

• where ammable liquids or vapors are used

or stored

• under dusty conditions

8. Do not burn solid fuel in the replace after

installing the log set. Do not use this log set

to cook food or burn paper or other objects.

9. Do not use appliance if any part has been

exposed to or under water. Immediately call

a qualied service technician to inspect the

room appliance and to replace any part of

the control system (if using GA9050A or

GA9150A) and any gas control which has

been under water.

SAFETy INFORMATION

Continued

10. To help prevent breakage, new logs must be

broken-in (see Curing Logs page 11).

11. Turn log set off and let cool before servicing,

installing, or repairing. Only a qualied ser-

vice person should install, service, or repair

log set.

12. Provide adequate clearances around air

openings.

13. This vented gas log set may not be installed

in a bedroom or bathroom in the Common-

wealth of Massachusetts.

PRODUCT

IDENTIFICATION

Figure 1 - Product Identication (Dual

Burner Shown)

Hearth Kit Model ____________________

Serial Number ______________________

Log Set Model ______________________

Grate

Burner

Pan

Burner

Manifold Burner Inlet

Fitting

Burner

Clamp

Grate

Steps

LOCAL CODES

Install and use log set with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

www.desatech.com

115043-01D 5

UNPACkING

CAUTION: Do not remove the

data plates from the burner pan.

The data plates contain impor-

tant product information.

1. Remove logs, hearth kit, pan materials, and

hardware from carton.

2. Remove all protective packaging applied to

logs and base for shipment.

3. Check all items for any shipping damage. If

damaged, promptly inform dealer where you

bought the product.

OPTIONAL PRODUCT

FEATURES

ON/OFF SAFETY VALVE/PILOT KIT

AND PROPANE/LP CONVERSION

An optional valve/safety pilot kit with a piezo

ignitor is available for this appliance. This system

requires no matches, batteries, or other sources to

light. You must use this optional system for LP

conversion. See Accessories, page 18.

REMOTE CONTROL READY

(MILLIVOLT) SAFETY VALVE/PILOT

KIT

An optional millivolt valve/safety pilot kit with a

piezo ignitor is available for this appliance. This

system requires no matches, batteries, or other

sources to light. This system may be connected to a

wall switch or hand-held wireless remote control.

See Accessories, page 18.

REMOTE CONTROL ACCESSORIES

There is an optional hand-held ON/OFF remote

control that can be purchased separately for this log

set. You must use the millivolt valve/safety pilot

kit to use remote accessories with this appliance.

See Accessories, page 18.

A wall switch is also available for this appliance.

You must use the millivolt valve/safety pilot kit

to use the wall switch with this appliance. See

Accessories, page 18.

INSTALLATION

CAUTION: Do not remove the

data plates attached to the burner

pan. The data plates contain im-

portant warranty information.

WARNING: Before installing

in a solid fuel burning replace,

the chimney ue and rebox

must be cleaned of soot, creo-

sote, ashes and loose paint by a

qualied chimney cleaner. Creo-

sote will ignite if highly heated.

A dirty chimney ue may create

and distribute soot within the

house. Inspect chimney ue for

damage. If damaged, repair ue

before operating appliance.

NOTICE: Installation, service,

and repair of this appliance must

be performed by a qualied in-

staller, service agency, company

or gas supplier experienced with

this type of gas appliance. Only

factory authorized components

listed in these instructions may

be used in accordance with the

manufacturer’s instructions and

all codes and requirements of

the authority having jurisdic-

tion. Any modications to this

kit, or use of unauthorized

components or accessory items

will void the manufacturer’s

warranty, and may result in a

hazardous condition.

FLUE OPENING SPECIFICATIONS

Note: This vented appliance must be installed only

in a solid-fuel burning replace with a working ue

and constructed of noncombustible material.

The charts in Figure 2, page 6 indicate technical

information regarding the installation of your gas

log set. Please make sure that all of the specica-

tions shown are applicable before installation is

attempted.

www.desatech.com 115043-01D6

The replace must include a working ue and

venting system with the minimum openings shown

in the Figure 2.

INSTALLATION

Continued

Figure 2 - Technical Information Charts

Model

Burner

Descrip-

tion

BTU Input

(Natural

Gas)

Min.

Vent

Opening

LCF18 18" Dual 55,000 8"

LCF24 24" Dual 60,000 8"

Minimum Fireplace Dimensions

Model Front

Width

Back

Width* Depth Height

LCF18 28" 18" 14" 16"

LCF24 29.75" 17" 15.5" 18"

* At depth Indicated

Fuel Inlet Pressure

Specications (W.C.)

Min. Max.

N.G. 5.5" 10.5"

Burner Orice Sizing

Log Size Natural Gas

In. Num.

18" .120 31

24" .129 30

CHECK GAS TYPE

Use only natural gas. If your gas supply is not

natural gas, you must install ON/OFF Safety

Valve/Pilot Kit (see Accessories, page 18). Call

dealer where you bought log set.

If the replace does not have a gas supply shutoff

valve, one must be installed.

VENTING SPECIFICATIONS FOR

INSTALLATION

The replace chimney ue and vent must be draft-

ing properly. To check the vent for proper drafting:

Light a tightly rolled newspaper on one end and

place it at the inside front edge of the replace.

Observe the smoke and be sure the vent is properly

drawing it up the chimney. If the smoke spills out

into the room, extinguish the ame and remove any

obstruction until proper venting is achieved.

The chimney ue must remain open a minimum

of 3" at all times during the operation of this

log set.

For Massachusetts Residents Only

Installation of this vented gas log set in the Com-

monwealth of Massachusetts requires the damper

be permanently removed or welded in the fully

open position.

INSTALLING DAMPER CLAMP

Secure the damper stop clamp provided to the

leading edge of the damper as shown in Figure 3.

If for any reason this clamp doesn't work on your

replace, another suitable clamp or permanent

stop must be installed, or the damper blade must

be cut or removed.

CONNECTING TO GAS SUPPLY

WARNING: A qualied ser-

vice person must connect log

set to gas supply. Follow all

local codes.

Installation Items Needed

Before installing log set, make sure you have the

items listed below.

• piping (check local codes)

• sealant (resistant to Propane/LP gas)

• equipment shutoff valve

• test gauge connection

• adjustable (crescent) wrench or pliers

• sediment trap

• tee joint

• pipe wrench

Figure 3 - Attaching Damper Clamp

Damper

Clamp

Damper

Clamp

Damper

Manufactured

Fireplace

Masonry Fireplace

Damper

www.desatech.com

115043-01D 7

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" diameter or greater to allow

proper gas volume to log set. If

pipe is too small, undue loss of

volume will occur.

Installation must include a equipment shutoff

valve, union, and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from log set (see

Figure 4).

IMPORTANT: Install equipment shutoff valve

in an accessible location. The equipment shutoff

valve is for turning on or shutting off the gas to

the appliance.

INSTALLATION

Continued

Figure 4 - Gas Connection

* Purchase the optional CSA design-certified

equipment shutoff valve from your dealer. See

Accessories, page 18.

** Minimum inlet pressure for purpose of input

adjustment.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could result

in a clogged burner injector.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

We recommend that you install a sediment trap in

supply line as shown in Figure 4. Locate sediment

trap where it is within reach for cleaning. Install in

piping system between fuel supply and appliance.

Locate sediment trap where trapped matter is not

likely to freeze. A sediment trap traps moisture and

contaminants. This keeps them from going into log

set controls. If sediment trap is not installed or is

installed wrong, log set may not run properly.

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an open

ame to check for a leak. Apply

a noncorrosive leak detection

uid to all joints. Bubbles form-

ing show a leak. Correct all leaks

at once.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect log set and its individual equipment

shutoff valve from gas supply piping system.

2. Cap off open end of gas pipe where equipment

shutoff valve was connected.

3. Pressurize supply piping system by either us-

ing compressed air or opening main gas valve

located on or near gas meter.

4. Check all joints of gas supply piping system.

Apply noncorrosive leak detection uid to gas

joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect log set and equipment shutoff

valve to gas supply. Check reconnected t-

tings for leaks.

3" Minimum

Sediment Trap

From Gas Meter

(5" W.C.** to

10.5" W.C.

Pressure)

CSA Design-Certied

Equipment Shutoff Valve

With 1/8" NPT Tap*

Approved Flexible Gas Hose (if

allowed by local codes)

Tee JointPipe Nipple

Cap

www.desatech.com 115043-01D8

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Figure 5).

2. Pressurize supply piping system by either us-

ing compressed air or opening main gas valve

located on or near gas meter.

3. Check all joints from gas meter to equipment

shutoff valve (see Figure 5). Apply noncorro-

sive leak detection uid to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

INSTALLATION

Continued

Figure 5 - Checking Gas Joints

HEARTH KIT ASSEMBLY AND

INSTALLATION

1. Determine which side the gas line will be coming

into the replace.

2. Using a hammer and screw driver, remove

knockout plug from the side of the pan that

corresponds to the gas line (see Figure 6).

3. Unscrew burner inlet fitting from burner

manifold.

4. Place burner manifold in pan with threaded

opening facing open knockout plug.

5. Using thread sealant (resistant to the action

of propane/LP gas) on larger end of tting,

screw the burner inlet tting through hole and

into burner manifold (see Figure 6). Tighten

using a wrench.

6. Using burner clamp, screw, and nut provided,

assemble clamp to pan (“U” style and triple

burners only). This will hold the burner mani-

fold in place.

7. If using optional GA9050A kit, go to Optional

GA9050A On/Off Safety Valve/Pilot Kit section

for installation instructions. If using optional

GA9150A kit, follow instructions included

with kit for installation and operation.

Figure 7 - Connecting Gas to Appliance

Adapter

Fitting

Gas

Connector

Tube

Burner Pan Assembly

(Facing Front of

Fireplace)

Figure 6 - Installing Burner

Burner Inlet

Fitting

Screw

Nut Burner

Clamp

Burner Pan

(Front)

Burner Manifold

Knockout

Plugs

Installation and Gas Connection

1. Place the burner pan assembly in the center

of the replace oor. Make sure the front of

pan faces forward.

2. Thread the gas supply tting to the replace

gas supply pipe. Use thread sealant.

3. Install adapter tting onto the burner inlet

tting using thread sealant on male threads

of burner inlet tting (see Figure 7). Adjust

to most convenient position.

4. Install the gas connector tube to the gas sup-

ply tting. Carefully shape tube to attach to

adapter tting. Be careful not to cause kinks

in tube.

Gas Meter

Equipment Shutoff Valve

www.desatech.com

115043-01D 9

INSTALLATION

Continued

OPTIONAL GA9050A ON/OFF

SAFETY VALVE/PILOT KIT

For additional convenience and safety, or for

propane/LP conversion, an optional ON/OFF

safety valve/pilot kit is available. See Accessories,

page 18.

WARNING: You must use a

ON/OFF safety valve/pilot kit for

propane/LP conversion.

TESTING BURNER FOR LEAKS

1. Generously apply noncorrosive leak detec-

tion uid to all connections.

WARNING: Never check for

gas leaks with open ame.

2. Light the burner with the shutoff valve no

more than half open and holding a match

slightly in front of the pan (see Lighting

Instructions, page 10).

3. Inspect all connections for bubbles, raw gas

odor, or ame from any area other than the

burner (leaks). If leaks are detected, shut off

the gas valve immediately. Tighten, or reas-

semble the loose connection(s) using pipe joint

compound until burner system is leak free.

4. When the burner is tested and leak free,

observe the individual tongues of ame on

the burner. Note: The burner design includes

more ports on the outside of the bar. Make

sure that all ports are clear and producing

ame evenly across the burner. If any ports

appear blocked, clear them by removing the

burner manifold and reaming the ports with a

modied paper clip or other suitable tool.

5. When nished testing, turn the gas shutoff

valve OFF to extinguish all ames.

ADDING PAN MATERIAL

1. Open the bag of ash bed material (vermiculite)

and spread it evenly across the burner pan

to the top. You may overow the front and

sides of the pan to cover the entire pan and

connecting hardware. Do not cover GA9050A

or GA9150A valve.

2. Open the glowing embers and evenly cover the

ash bed material (vermiculite) in the burner pan.

INSTALLING THE GRATE AND LOGS

1. Place the grate over the burner pan where the

two outer horizontal supports on the grate t

into the two pan positioning notches in the

rear vertical edge of the pan.

2. Slide the two rear log grate steps over the

two outer horizontal supports on the grate as

shown in Figure 8.

3. Place the back log onto the grate steps (see

Figure 9).

4. Place the front log(s) on the grate and slide

forward against the front bars on the grate

(see Figure 9).

5. Place three middle logs on top of bottom logs

(see Figure 10, page 10).

6. Place the smaller top logs onto the bottom logs

(see Figure 11, page 10). Leave as much open

space between logs as possible to minimize

ame impingement and sooting. Note: Logs

may chip if they are handled roughly or if hit

together while being placed.

Figure 8 - Installing Grate (Pan Material

Not Shown)

Grate

Grate Steps

Figure 9 - Installing Bottom Logs

www.desatech.com 115043-01D10

INSTALLATION

Continued

Figure 11 - Installing Top Logs

Figure 10 - Installing Middle Logs

OPERATING APPLIANCE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: Keep ue open

when operating unit.

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result

causing property damage, per-

sonal injury or loss of life.

BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next to

the oor because some gas is heavier than air

and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the re department.

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information, above.

2. Turn the gas shutoff valve to OFF.

3. Wait ve (5) minutes to clear out any gas. If

you then smell gas STOP! Follow the safety

information above. If you don't smell gas,

go on to the next step.

4. Light a match and lay it on top of the pan

material about 2" from the end of the sup-

ply side of the pan

5. Slowly turn the gas shutoff valve ON until

the burner ignites. If the burner doesn’t

ignite within 10 seconds with the match

burning, turn the shutoff valve OFF and

repeat steps 1 through 4 again.

GAS SHUTOFF

VALVE OPERATION

Flame Adjustment

Adjust the ame ON/OFF by turning the gas

shutoff valve counterclockwise to open or

clockwise to close, as necessary.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Comfort Glow Gasheizung Handbücher

Comfort Glow

Comfort Glow GLD2466R Bedienungsanleitung

Comfort Glow

Comfort Glow and CVDR30 Kurzanleitung

Comfort Glow

Comfort Glow RADIANT FLAME RFN28TD Kurzanleitung

Comfort Glow

Comfort Glow CRP16, CRP16T, CRN18, CRN18T CRP26 Originalbetriebsanleitung

Comfort Glow

Comfort Glow CGS2718N Kurzanleitung

Comfort Glow

Comfort Glow (VENT-FREE) GAS STOVE HEATER Bedienungsanleitung

Comfort Glow

Comfort Glow Comfort Glow RFN28TC Kurzanleitung

Comfort Glow

Comfort Glow Comfort Glow RGA 2-72 Kurzanleitung

Comfort Glow

Comfort Glow CGP20TB Kurzanleitung

Comfort Glow

Comfort Glow CCL3018P Kurzanleitung

Comfort Glow

Comfort Glow CG3324PTA Bedienungsanleitung

Comfort Glow

Comfort Glow CGP28TB Kurzanleitung

Comfort Glow

Comfort Glow CG3324NTA Kurzanleitung

Comfort Glow

Comfort Glow 000 to 30 Kurzanleitung

Comfort Glow

Comfort Glow CRL2718PA Kurzanleitung

Comfort Glow

Comfort Glow KWD216 Bedienungsanleitung

Comfort Glow

Comfort Glow Comfort Glow CGD3018N Kurzanleitung

Comfort Glow

Comfort Glow CGD3924PR Bedienungsanleitung

Comfort Glow

Comfort Glow CGD3018P Kurzanleitung

Comfort Glow

Comfort Glow KWD155 Bedienungsanleitung

Comfort Glow

Comfort Glow CCL3924NRA Bedienungsanleitung

Comfort Glow

Comfort Glow CGN10LA Kurzanleitung

Comfort Glow

Comfort Glow GHN 18 Handbuch

Comfort Glow

Comfort Glow GLD1856T Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung