Comfort Glow CF26PR Kurzanleitung

Save this manual for future reference.

OWNER’S OPERATION AND INSTALLATION MANUAL

VENT-FREE PROPANE/LP GAS

BAY FRONT FIREPLACE

CF26PR

19,000 to 26,000 Btu/Hr

Remote Control Ready

WARNING: If the information in this manual is not

followedexactly,afireorexplosionmayresultcaus-

ing property damage, personal injury, or loss of life.

— Donotstoreorusegasolineorotherflammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’sphone.Followthegassupplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installation and service must be performed by

aqualified installer,service agency,or thegas

supplier.

WARNING:Improperinstallation,

adjustment, alteration, service,

ormaintenancecancauseinjury

orpropertydamage.Refertothis

manual for correct installation

andoperationalprocedures.For

assistance or additional infor-

mation consult a qualified in-

staller, service agency, or the

gas supplier.

WARNING: This is an unvented

gas-firedheater.Itusesair(oxy-

gen)fromtheroominwhichitis

installed. Provisions for ad-

equatecombustionandventila-

tion air must be provided. Refer

Air for Combustion and Ven-

tilation

sectiononpage4ofthis

manual.

AUTO

OFF

This appliance may be installed in an aftermarket*, permanently located, manufactured

(mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Patent Pending

Fireplace Shown

With Optional

Bay Front Mantel

105442

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

CF26PR

For more information, visit www.desatech.com

1. This appliance is only for use with the

typeof gasindicated ontherating plate.

Thisappliance isnot convertible foruse

with other gases.

2. Do notplacepropane/LP supplytank(s)

inside any structure. Locate propane/

LP supply tank(s) outdoors.

SAFETY

INFORMATION

Carbon Monoxide Poisoning: Early signs

ofcarbonmonoxidepoisoningresemblethe

flu, with headaches, dizziness, or nausea. If

you have these signs, the fireplace may not

beworkingproperly.Getfreshairatonce!

Have fireplace serviced. Some people are

more affected by carbon monoxide than

others. These include pregnant women,

peoplewithheartorlungdiseaseoranemia,

those under the influence of alcohol, and

those at high altitudes.

Propane/LP Gas: Propane/LP gas is odor-

less. An odor-making agent is added to pro-

pane/LP gas. The odor helps you detect a

propane/LPgasleak.However,theodoradded

to propane/LP gas can fade. Propane/LP gas

may be present even though no odor exists.

Make certain you read and understand all

warnings.Keepthismanualforreference.It

isyourguidetosafeandproperoperationof

this fireplace.

WARNING ICON G 001

WARNINGS

IMPORTANT: Read this owner’s

manual carefully and completely

beforetryingtoassemble,operate,

or service this fireplace. Improper

use of this fireplace can cause se-

rious injury or death from burns,

fire,explosion,electricalshock,and

carbon monoxide poisoning.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions

• ifyou cannotreach yourgas supplier,

call the fire department

4. This fireplace shall not be installed in

a bedroom or bathroom.

5. Do not use this fireplace as a wood-

burning fireplace. Use only the logs

provided with the fireplace.

6. Do not add extra logs or ornaments

suchas pine cones, vermiculite, or rock

wool. Using these added items can

cause sooting. Do not add lava rock

aroundbase. Rockand debriscould fall

into the control area of fireplace.

7. This fireplace is designed to be smoke-

less. If logs ever appear to smoke, turn

off fireplace and call a qualified ser-

vice person.

Note:

During initial op-

eration,slight smokingcould occurdue

to log curing and fireplace burning

manufacturing residues.

8. To prevent the creation of soot, follow

the instructions in Cleaning and Main-

tenance, page 19.

9. Before usingfurniture polish,wax, car-

pet cleaner, or similar products, turn

heater off. If heated, the vapors from

theseproducts may create a white pow-

der residue within burner box or on

adjacent walls or furniture.

10. This fireplace needs fresh air ventila-

tion to run properly. This fireplace has

an Oxygen Depletion Sensing (ODS)

safety shutoff system. The ODS shuts

down the fireplace if not enough fresh

air is available. See Air for Combus-

tion and Ventilation, pages 4 through

6. If fireplace keeps shutting off, see

Troubleshooting, pages 20 through 22.

11. Do not run fireplace

• where flammable liquids or vapors

are used or stored.

• under dusty conditions.

12. Do not use this fireplace to cook food

or to burn paper or other solid fuels.

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING:Anychangetothis

heater or its controls can be

dangerous.

WARNING: Do not allow fans

toblowdirectlyintothefireplace.

Avoidanydraftsthatalterburner

flame patterns. Ceiling fans can

create drafts that alter burner

flame patterns. Altered burner

patterns can cause sooting.

WARNING: Do not use a

blower insert, heat exchanger in-

sert, or other accessory not ap-

proved for use with this heater.

Due to high temperatures, the

appliance should be located out

oftrafficand away from furniture

and draperies.

Do not place clothing or other

flammable material on or near

the appliance. Never place any

objectsinthefireplaceoronlogs.

Fireplace front and screen be-

come very hot when running

heater. Keep children and adults

away from hot surface to avoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surface to

cool before touching.

Carefully supervise young chil-

dren when they are in the room

with fireplace. When using the

hand-held remote accessory,

keep selector switch in the OFF

positiontopreventchildrenfrom

turning on burners with remote.

You must operate this fireplace

with a fireplace screen in place.

Make sure fireplace screen is

closed before running heater.

Keeptheapplianceareaclearand

free from combustible materials,

gasoline, and other flammable

vapors and liquids.

105442

OWNER’S MANUAL

For more information, visit www.desatech.com

AUTO

OFF

PRODUCT

IDENTIFICATION

LOCAL CODES

Install and use fireplace with care. Follow all

local codes. In the absence of local codes, use

the latest edition of The National Fuel Gas

Code,ANSZ223.1,alsoknownasNFPA54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Figure 1 - Vent-Free Propane/LP Gas Compact Fireplace

UNPACKING

1. Remove and fireplace from carton.

2. Remove all protective packaging ap-

plied to fireplace for shipment.

3. Make sure your fireplace includes one

hardware packet.

4. Checkfireplaceforanyshippingdamage.

If fireplace is damaged, promptly inform

dealer where you bought fireplace.

PRODUCT

FEATURES

SAFETY PILOT

This fireplace has a pilot with an Oxygen

DepletionSensing(ODS)safetyshutoffsys-

tem. The ODS/pilot is a required feature for

vent-free room fireplaces. The ODS/pilot

shuts off the fireplace if there is not enough

fresh air.

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This sys-

tem requires no matches, batteries, or other

sources to light fireplace.

Heater Controls

(Inside Door)

Screen

Fireplace

Cabinet

Logs

REMOTE CONTROL

ACCESSORIES

There are two optional remote controls that

can be purchased separately for this log

heater:

• hand-held ON/OFF remote

• hand-held thermostat remote

See Accessories, page 28.

Brick

Liner

SAFETY

INFORMATION

Continued

13. Do notuse fireplaceif any parthas been

under water. Immediately call a quali-

fied service technician to inspect the

room fireplace and to replace any part

of the control system and any gas con-

trol which has been under water.

14. Turn off and unplug fireplace and let

cool before servicing. Only a qualified

service person should service and re-

pair fireplace.

15. Operating fireplaceabove elevationsof

4,500 feet could cause pilot outage.

16. Do not operate fireplace if any log is

broken. Do not operate fireplace if a

log is chipped (dime-sized or larger).

17. To prevent performance problems, do

not use propane/LP fuel tank of less

than 100 lbs. capacity.

105442

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

CF26PR

For more information, visit www.desatech.com

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

help reduce heat loss in homes. Home

owners weather strip and caulk around

windowsanddoors tokeepthe cold airout

andthewarmairin.Duringheatingmonths,

home owners want their homes as airtight

as possible.

Whileitisgoodtomakeyourhomeenergy

efficient,yourhomeneedstobreathe.Fresh

airmustenter your home.Allfuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers,

and fuel burning appliances draw air from

the house to operate. You must provide

adequate fresh air for these appliances.

This will insure proper venting of vented

fuel-burning appliances.

Confined and Unconfined Space

The National Fuel Gas Code, ANS Z223.1

defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m3per kw) of the aggre-

gate input rating of all appliances installed

in that space and an unconfining space as a

space whose volume is not less than 50

cubicfeetper1,000Btuperhour(4.8m3per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

whichtheappliancesareinstalled*,through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

This heater shall not be installed in a con-

fined space or unusually tight construction

unlessprovisionsare providedforadequate

combustion and ventilation air.

*Adjoiningroomsarecommunicatingonly

iftherearedoorlesspassagewaysorventila-

tion grills between them.

WARNING: This heater shall

notbeinstalledinaconfinedspace

or unusually tight construction

unless provisions are provided

foradequatecombustionandven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National

Fuel Gas Code, NFPA 54/ANS Z223.1, Sec-

tion5.3,AirforCombustionandVentilation.

Allspacesinhomesfallintooneofthethree

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is de-

fined as construction where:

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10-11 kg

per pa-sec-m2) or less with open-

ings gasketed or sealed

and

b. weather stripping has been

added on openable windows and

doors

and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors,be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tionsforplumbing,electrical,and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See

Ventilation Air

From Outdoors

, page 6

If your home does not meet all of the

threecriteria above,proceedto

Deter-

mining Fresh-Air Flow For Fireplace

Location,

page 5

AIR FOR

COMBUSTION AND

VENTILATION

105442

OWNER’S MANUAL

For more information, visit www.desatech.com

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = ____________________ cu. ft. (volume of space)

Example:

Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_________________ (volume of space) ÷50 cu. ft. = (Maximum Btu/Hr the space can support)

Example:

2560 cu. ft. (volume of space) ÷50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free fireplace _________________Btu/Hr

Gas water heater* _________________Btu/Hr

Gas furnace _________________Btu/Hr

Vented gas heater _________________Btu/Hr

Gas fireplace logs _________________Btu/Hr

Other gas appliances* +_________________Btu/Hr

Total =_________________Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

___________ Btu/Hr (maximum the space can support)

___________ Btu/Hr (actual amount of Btu/Hr used)

Example:

51,200 Btu/Hr (maximum the space can support)

56,000 Btu/Hr (actual amount of Btu/Hr used)

ThespaceintheaboveexampleisaconfinedspacebecausetheactualBtu/HrusedismorethanthemaximumBtu/Hrthespacecansupport.

You must provide additional fresh air. Your options are as follows:

Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoining

room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING:Iftheareainwhichtheheatermaybeoperatedissmallerthanthatdefinedasanunconfinedspace

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

the methods described in the

National Fuel Gas Code, ANS Z223.1, Section 5.3

or applicable local codes.

AIR FOR

COMBUSTION AND

VENTILATION

Continued

Example:

Gas water heater 30,000 Btu/Hr

Vent-free fireplace +26,000 Btu/Hr

Total = 56,000 Btu/Hr

Continued

105442

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

CF26PR

For more information, visit www.desatech.com

Figure 3 - Ventilation Air from Outdoors Shown with Optional Mantel

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connecttheseitemsdirectlytotheoutdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces. Follow the

National Fuel Gas Code, NFPA 54/ANS

Z223.1, Section 5.3, Air for Combustion

and Ventilation for required size of ventila-

tion grills or ducts.

IMPORTANT:

Do not provide openings for

inletoroutletairintoatticifattichasathermo-

stat-controlled power vent. Heated air enter-

ing the attic will activate the power vent.

Outlet

Air Ventilated

Attic

Outlet

Air

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

AIR FOR

COMBUSTION AND

VENTILATION

Continued

Figure 2 - Ventilation Air from Inside Building Shown with Optional Mantel

VENTILATION AIR

Ventilation Air From Inside

Building

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(seeoptions1and2,Figure2).Youcanalso

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code, NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills

into Adjoining

Room,

Option 1

WARNING: Rework work-

sheet, adding the space of the

adjoiningunconfinedspace.The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

105442

OWNER’S MANUAL

For more information, visit www.desatech.com

INSTALLATION

Note:

Your Comfort Glow fireplace is de-

signed to be used in zero clearance installa-

tions.Wallorframingmaterialcanbeplaced

directlyagainst anyexteriorsurface ofyour

fireplace,exceptwherestandoffspacersare

integrally attached. If standoff spacers are

attachedtoyourfireplace,thesespacerscan

be placed directly against wall or framing

materials.

Use the dimensions shown for rough open-

ings to create the easiest installation (see

Built-In Fireplace Installation, page 8).

CHECK GAS TYPE

Useonlypropane/LPgas.Ifyourgassupply

is not propane/LP, do not install fireplace.

Call dealer where you bought fireplace for

proper type fireplace.

INSTALLATION ITEMS

Before installing fireplace, make sure you

have the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• test gauge connection*

WARNING: A qualified ser-

vicepersonmustinstallfireplace.

Follow all local codes. You can recess firebox into the wall. You

can also position fireplace in the optional

cabinetmantels.

IMPORTANT:

Onlyuse

optional cabinet mantels specified in this

manual.Purchasetheoptionalmantelfrom

your dealer (see Accessories, page 28).

CAUTION: This fireplace cre-

ateswarmaircurrents.Thesecur-

rents move heat to wall surfaces

next to fireplace. Installing fire-

place next to vinyl or cloth wall

coverings or operating fireplace

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

WARNING: Never install the

fireplace

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objectsarelessthan42inches

from the front, top, or sides of

the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

MPORTANT:

Vent-freefireplacesaddmois-

ture to the air. Although this is beneficial,

installing fireplace in rooms without enough

ventilation air may cause mildew to form

fromtoomuchmoisture.SeeAirforCombus-

tion and Ventilation, pages 4 through 6.

LOCATING FIREPLACE

WARNING:Maintainthemini-

mumclearancesshowninFigure

4.Ifyoucan,providegreaterclear-

ancesfromfloor,ceiling,andjoin-

ing wall.

CAUTION: If you install the

fireplace in a home garage

• fireplacepilotandburnermust

be at least 18 inches above

floor.

• locate fireplace where moving

vehicle will not hit it.

Forconvenienceandefficiency,installfire-

place

• where there is easy access for operation,

inspection, and service.

• in coldest part of room.

An optional blower kit is available from

your dealer. See Accessories, page 28. If

planningtouseblower,locatefireplacenear

an electrical outlet.

NOTICE: This heater is intended

foruseas supplementalheat.Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heatsource.If youhavea central

heating system, you may run

system’scirculatingblowerwhile

usingheater.Thiswillhelpcircu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

* ACSAdesign-certifiedequipmentshutoff

valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Pur-

chase the optional CSA design-certified

equipment shutoff valve from your dealer.

See Accessories, page 28.

Note:

Ifdesired,purchaseafour-sidedbrass

trimkitfor built-in installations.SeeAcces-

sories, page 28.

Continued

Minimum Clearances For Side

Combustible Material, Side Wall,

and Ceiling

A. Clearances from thesideof thefireplace

cabinetto anycombustible material and

wall should follow diagram in Figure 4.

Example:

The face of a mantel, book-

shelf, etc. is made of combustible ma-

terial and protrudes3 1/2"from thewall.

This combustible material must be 4"

from the side of the fireplace opening

(see Figure 4).

B. Clearancesfrom thetop ofthe fireplace

openingto theceiling should notbe less

than 42 inches.

C. For mantel clearances, see Figure 8 on

page 9.

.5 2

7/16

7/8

1 4 6 8 10 12 14 16

FIREBOX INCHES

INCHES

Figure 4 - Minimum Clearance for

Combustible to Wall

*Minimum 16 inches from Side Wall

Example

105442

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

CF26PR

For more information, visit www.desatech.com

INSTALLATION

Continued

"25

Figure6-RoughOpeningforInstallingin

Corner

2. An optional blower accessory is avail-

able (see Accessories, page 28). There

are two options for connecting blower

to electrical source.

Option one: Have a licensed electri-

cian install a properly grounded, three-

prong 120-volt electrical outlet at fire-

place location. Locate outlet inside the

framed enclosure. Blower power cord

will plug into this outlet.

Option two: Have a licensed electri-

cianconnect blowerto electricalsource

at junction box inside fireplace.

If using option one, have electrical out-

let installed at this time. If using option

two, do not connect blower to electrical

source at junction box until step 6.

3. Install gas piping to fireplace location.

This installation includes an approved

flexible gas line (if allowed by local

codes) after the equipment shutoff

valve. The flexible gas line must be the

last item installed on the gas piping.

4. Carefully set fireplace in front of rough

opening with back of fireplace inside

wall opening.

5. Attach flexible gas line to fireplace gas

regulator. See Connecting Fireplace to

Gas Supply, page 13.

6. If theoptional blower hasbeen installed

connect blower to electrical source.

Option one: Route blower electrical

cord through side or rear access door

of fireplace. Plug electrical cord into

electrical outlet.

Option two: Have a licensed electri-

cianconnect blowerto electricalsource

at junction box inside fireplace.

7. Bend four nailing flanges on outer cas-

ing with pliers (see Figure 7).

8. Attach fireplace to wall studs using

nails or wood screws through holes in

nailing flange.

9. Check allgasconnections forleaks. See

Checking Gas Connections, page 14.

IMPORTANT:

When finishing your fire-

box,combustiblematerialssuchaswallboard,

gypsumboard,sheetrock,drywall,plywood,

etc.maybebuttedupnexttothesidesandtop

ofthefirebox.Combustiblematerialsshould

never overlap the firebox front facing. Fire-

box should not be placed on top of carpet or

other kinds of fibrous material.

1. Frame in rough opening. Use dimen-

sions shown in Figure 5 for the rough

opening.

If installing in a corner, use dimensions

shown in Figure 6 for the rough open-

ing. The height is 26 1/8" which is the

same as the wall opening above.

3/4" Off

The Floor

Minimum

Figure5-RoughOpeningforInstallingin

Wall

BUILT-IN FIREPLACE

INSTALLATION

Built-ininstallationofthisfireplaceinvolves

installing fireplace into a framed-in enclo-

sure. This makes the front of fireplace flush

with wall. Follow the instructions below to

installthefireplaceinthismanner.Ifinstall-

ing a built-in mantel above the fireplace,

you must follow the clearances shown in

Figure 8, page 9. If using for built-in instal-

lation off of the floor, follow clearances

shown in Figure 3, page 7.

Actual Framing

Height 26" 26 7/8"

Front Width 26 3/4" 26 7/8"

Depth 9 1/2" 10 1/2"

Bottom 3/4"3/4"

Figure 7 - Attaching Fireplace to Wall

Studs

WARNING: Do not allow any

combustiblematerialstooverlap

the firebox front facing.

IMPORTANT:

Noncombustible materials

suchasbrick,tile,etc.mayoverlapthefront

facing, but should never cover any neces-

sary openings like louvered slots.

WARNING: Do not allow non-

combustible materials to cover

anynecessaryopeningslikelou-

vered slots.

WARNING:Useonlynoncom-

bustible mortar or adhesives

when overlapping the front fac-

ing with noncombustible facing

material.

WARNING: Never modify or

cover the louvered slots on the

front of the firebox.

Nails or

Wood

Screws

AUTO

OFF

Nailing

Flanges

105442

OWNER’S MANUAL

For more information, visit www.desatech.com

13"

16"

19"

21"

2 1/2"

10"

Minimum Non-

Combustible

Material

MANTEL CLEARANCES FOR

BUILT-IN INSTALLATION

Figure 8 - Minimum Mantel Clearances

for Built-In Installation

Mantel Shelf

INSTALLATION

Continued

Note:

All vertical

measurements

are from top of

fireplace

opening to

bottom of

mantel shelf.

ASSEMBLING BRASS TRIM

(Brass trim shipped with mantel)

1. Remove packaging from three pieces

of brass trim.

2. Locate two adjusting plates with set

screws, and two shims in the hardware

packet.

3. Align shim under adjusting plate as

shown in Figure 9.

4. Slide one end of adjusting plate/shim

inslot onmitered edgeof topbrass trim

(see Figure 9).

5. Slide other end of adjusting plate/shim

in slot on mitered edge of side brass

trim (see Figure 9).

6. While firmly holding edges of brass

trim together, tighten both set screws

on the adjusting plate with slotted

screwdriver.

7. Repeat steps 1 through 6 for other corner.

8. Set brass assembly aside for later

installation.

REMOVING BRICK LINER

RETAINER

1. Using Phillips screw driver, remove 2

screws attaching brick liner retainers to

vertical sides.

2. Removebricklinerretainersanddiscard.

Replace 2 screws into vertical sides.

OPTIONAL MANTEL

INSTALLATION

Note:

Refer to instructions provided with

the mantel for assembly instructions. Refer

to instructions below for system installa-

tion. If using blower accessory (see Acces-

sories, page 28), see installation instruc-

tions on pages 10 and 11.

Choose location for fireplace and in-

stall gas supply line.

2. Remove screen from fireplace by re-

moving screws in each end of screen

rod (see Figure 10). Hold screen rod

cover while removing five hex head

screws underneath hood (see Figure

11). Carefullyliftand pullout hood(see

Figure 12).

3. Assemble brass trim kit. See Assem-

bling Brass Trim, column 2.

Continued

Figure 11 - Removing Hood Screws

Hood

Screen

Rod

Cover

Screw

Figure 12 - Removing Hood

Mantel Screw

Location

Figure 10 - Removing Screen

Figure 9 - Assembling Brass Trim

Top

Brass

Trim

Side

Brass

Trim

Mitered

Edge

Shim

Set Screws

Adjusting

Plate

Slot

NOTICE:If yourinstallationdoes

notmeettheminimumclearances

shown, you must do one of the

following:

• raise the mantel to an accept-

able height

• remove the mantel

NOTICE:Surfacetemperaturesof

adjacent walls and mantels be-

comehotduringoperation.Walls

and mantels above the firebox

may become hot to the touch. If

installedproperly,thesetempera-

turesmeettherequirementofthe

national product standard. Fol-

low all minimum clearances

shown in this manual.

If placing mantel above built-in fireplace,

youmustmeetminimumclearancebetween

mantel shelf and top of fireplace opening.

105442

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

CF26PR

For more information, visit www.desatech.com

INSTALLATION

Continued

Note:

If you are using a mantel with your

heater, use the following instructions. If

your heater is built-in, see For Built-In In-

stallation on page 11.

1. Screen and hood should be removed

from fireplace (see page 9). Remove

log set and set aside.

2. Install snapbushingsfound inhardware

kit into both holes in rear of blower

control shield (see Figure 14).

3. Make sure the wire harness is firmly

connectedtothe terminalsontheblower

bracket assembly.

4. Note the wire locations on back of

AUTO/OFF/ON switch. Carefully re-

move red wire from the AUTO termi-

nal and blue wire from the ON termi-

nal. Black wire can remain on the

middleor OFFterminal(see Figure15).

5. Carefully disconnect green and white

wires from power cord harness at their

insulated connectors.

6. In top of the heater cabinet, locate the

four mounting holes on the outer cas-

ing. Align these four holes with those

on the blower bracket assembly.Attach

blower bracket assembly to the outer

casing with 4 - #10 screws provided

(see Figure 15).

7. Route thewire harness throughthe hole

to the left side of heat deflector. Pull

wire harness through lower opening to

theleft oftheblower controlshield.(see

Figure 15).

8. Insert the 4 wire harness into one of the

roundholesintherearof the blowercon-

trol shield and through the rectangular

holeinthefrontofshield(see Figure 15).

Snap

Bushing

Figure 14 - Installing Snap Bushings

Blower

Control

Shield

Figure 15 - Installing Blower Bracket Assembly

Switch Plate

4. Place brass trim on the shoulder screws

locatedonthesideandtopofthefireplace.

Firmlysnap thebrass trimover theshoul-

der screws on fireplace (see Figure 13).

5. Place mantel base close to wall in de-

sired fireplace location.

6. Install gas line. See Connecting To Gas

Supply, page 12

7. Carefully place fireplace on mantel base

andcenterlefttoright.Checkforgasleaks.

See Checking Gas Connections, page 14.

8. Refer to instructions provided with the

mantelforpermanentattachmenttowall.

9. Slide mantel around fireplace. Be care-

ful not to damage wall or mantel.

10. Adjust assembly to remove any gaps.

From back side of fireplace, attach two

2" wood screws through base mount-

ing blocks attached to bottom sides of

mantel into base (see instructions pro-

vided with mantel).

11. Attach remaining two 3" wood screws

from hardware pack through openings

inside of fireplace sides into the mantel.

See Figure 12, page 9, for screw hole

location.

Figure13-AttachingBrassTrimtoFireplace

AUTO

OFF

Shoulder

Screws

Assembled

Brass Trim

AUTO

OFF

Wire Harness

Blower Bracket

Assembly

Screw

Power

Cord

Blower

Control

Shield Shield Cover

Wire

Harness

Switch

Heat

Deflector

Wiring

Routing Hole

Blue Red

CAUTION: Label allwiresprior

to disconnection when servicing

controls. Wiring errors can cause

improperanddangerousoperation.

CAUTION: Verify proper op-

eration after servicing.

INSTALLING BLOWER

ASSEMBLY - GA3450T

Andere Handbücher für CF26PR

Inhaltsverzeichnis

Andere Comfort Glow Kamin im Innenbereich Handbücher

Comfort Glow

Comfort Glow ELCG 125 Montageanleitung

Comfort Glow

Comfort Glow 23-800-001 Kurzanleitung

Comfort Glow

Comfort Glow CDV37N Kurzanleitung

Comfort Glow

Comfort Glow Comfort Glow CHDV34NA Kurzanleitung

Comfort Glow

Comfort Glow QSF8208R Montageanleitung

Comfort Glow

Comfort Glow CGCFTP Kurzanleitung

Comfort Glow

Comfort Glow CGFB32CA Circulating Louvered Originalbetriebsanleitung

Comfort Glow

Comfort Glow CHDV32NR Kurzanleitung

Comfort Glow

Comfort Glow EF6021R Montageanleitung

Comfort Glow

Comfort Glow CDV37N/PA Kurzanleitung

Comfort Glow

Comfort Glow CGFB32CC Kurzanleitung

Comfort Glow

Comfort Glow CF26NT Kurzanleitung

Comfort Glow

Comfort Glow CGFB36C Kurzanleitung

Comfort Glow

Comfort Glow Freestanding Electric Fireplace EF5802R Montageanleitung

Comfort Glow

Comfort Glow EF5675R Montageanleitung

Comfort Glow

Comfort Glow EF6033R Montageanleitung

Comfort Glow

Comfort Glow GLD2470R Bedienungsanleitung

Comfort Glow

Comfort Glow CGCFTN Kurzanleitung

Comfort Glow

Comfort Glow CF26PRA Kurzanleitung

Comfort Glow

Comfort Glow Vent-Free Gas and Electric Hearth Bedienungsanleitung

Comfort Glow

Comfort Glow CS26NT Kurzanleitung

Comfort Glow

Comfort Glow 901910-01A.pdf Kurzanleitung

Comfort Glow

Comfort Glow CPVSA18R Kurzanleitung

Comfort Glow

Comfort Glow EF5566R Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch