Command access PM300 Bedienungsanleitung
Page 1
INSTALLATION INSTRUCTIONS
PM300/PM300D
Doc # 20075-A
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
A.
Includes
A. 12” Retrot Wiring Harness
B. PM300 Module
C. 6’ Power Lead.
D. 3/4”Velcro
E. Wire Connectors
Tools Required
• Wire Stripper
The PM300 is a power booster interface module that ts inside of an electric latch pullback exit device.
When installed in the exit device, it typically allows for a much longer wire run from the power supply to the
exit device (typically up to 700’ with 18/2 wire) .
B.
C.
E.
**Please See Last Page for Technical Information**
D.
Page 2
24 VDC
Solenoid
To the power supply
PM300
How to hook it up for Command Access & Von Duprin Devices:
The unit comes with an easy plug-in 3 prong connector that connects directly to Command Access and Von Duprin solenoids.
There is a second easy plug-in 2 prong connector that connects to the 6’ power lead. The 6’ power lead should be connected to
the positive and negative leads from the power supply.
Module
Ceiling Tile
Module
LPM1 Series Installation
Example
Exit Device Installation
Example
STANDARD PLACEMENT
Optional Placement
Standard Placement
Optional Placement
DOUBLE
GANG
BOX
Module
CAT
PM300 Flow Diagram
Note: For LPM1 series PM300 must be paired with a
Command Access PS210, 220/220B, PS440B, P1, or PS5-4
power supply.
Recommended Mode
Page 3
Cut wires from Adams Rite Circuit board and remove board.
Tape back the two Blue wire.
A.
Adams Rite wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
How to hook it up for other Manufactures Devices:
The unit comes with an easy plug-in 3 prong wire harness that to retrots to the existing solenoid. There is a second easy plug-in
2 prong wire harness that connects to the power from the power supply. The harness should be connected to the positive and
negative leads from the power supply. Generic examples and specic retrots are shown below.
B.
Connect White and Red wires from solenoid to White wire from harness. Next, connect Black wire from
solenoid to Black wire from harness. Next, connect PM300.
Harness White (PM300-Yellow).
C.
PM300
Harness Black (PM300 Green).
Primary
Solenoid
Primary
Solenoid
Primary
Solenoid
Black
Red
White
Remove Circuit Board
Blue
Recommended Mode
Page 4
White #1
White
#2
Black #1
Harness White (PM300 Yellow)
Harness Black (PM300 Green)
Black #2
Precision pushpad and housing
Red #1
Black #1
Black #2
Black #2
Harness White (PM300 -Yellow)
Harness Black (PM300-Green)
Connect Red #1 solenoid wire to White harness wire. Next, connect Black #1 to Black harness wire.
Disregard the two Secondary Black wires. Next, connect PM300.
Corbin/Russwin wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
Precision wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
Primary
Solenoid
Secondary
Solenoid
Remove
B.
PM300
Connect primary White #1 wire to White harness wire. Next connect White #2 wire to Black harness wire.
Disregard both Black #2 wires. Next, connect PM300.
A.
PM300
Black #2
Red #1
Black #1
Black #2
Cut wires to disconnect solenoid from circuit board. Remove circuit board.
A.
Recommended Mode
Recommended Mode
Page 5
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
TECHNICAL INFORMATION
PM300/PM300D
• Wires: Input to PM300 non-polarized Black (+)(-) • Operating Voltage Range: 22-30 VDC
Power Supply Options for PM300 and PM300D in Standard Mode:
The PM300 works best with the Command Access PS210, PS220/220B, PS440B, PS480B, PS1, PS2, & PS5 series
regulated power supplies. The PM300 also works with most Regulated power supplies rated at 24VDC and
1.5A or higher. Although we do not recommend using power supplies that we have not thoroughly tested
with the PM300. Please check our compatibility chart in link below for a list of other manufactures power
supplies.
Models:
Power Supply Options for PM300 and PM300D in High Output Mode:
In High Output mode, the PM300 is designed for & MUST BE powered by the Command Access PS210,
PS220/220B, PS440B, PS1, and PS5-4 power supplies only.
Standard model designed to work with 24 VDC regulated power supplies. 12” retrot wiring
harness for other manufactures, such as, Adams Rite, Corbin/Yale, Precision, and more.
-PM300
PM300D - Same as PM300 above with the added feature of a .5 second delay.
Wire Run Guidelines:
For best results we recommend that your maximum wire run not exceed the following:
18ga.= 700’ 16ga. = 1000’ 14ga. = 1250’ 12ga. = 1500’.
Specications:
PM300 Compatibility Chart
• Fuse: Glass 3.5 - 5A, Resettable 1A trip
• Relay: 5A or greater
• Fuse: Resettable 2A trip
• Relay: 10A or greater
Standard Mode High Output Mode
• Output from PM300: Yellow=Pull Coil; Orange= Hold Coil; Green=Common
Note: High Output is recommended for sluggish devices, vertical rods, & overcoming door misalignment.
Scan me
Switch
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Command access Aufnahmegeräte Handbücher
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
